• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.6C
• /
• pp.495-505
• /
• 2010

In this paper, the effect of Near-Far Problem (NFP) among distributed nodes in OFDMA-based Wireless Mesh Networks (WMNs) is analyzed by investigating statistical characteristics of Time Difference of Arrival (TDoA) and Desired-to-Undesired power Ratio (DUR). In order to overcome the effects of Inter-Symbol Interference (ISI), Inter-Carrier Interference (ICI), and Inter Link Interference (ILI), caused by TDoA in WMNs, we derive effective SINR for each subcarrier, and then, propose the optimal starting point of FFT window which can minimize BER for each subcarrier. In addition, we propose a subcarrier-based Zero Forcing - 2 Dimensional Ordered Successive Interference Cancellation (ZF-2DOSIC) technique for signal detection in WMNs with TDoA. It is verified by simulation that the effective SINR and uncoded BER performances of the proposed signal detection technique for OFDMA-based WMNs are significantly improved, compared with those of conventional technique.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.7 no.1
• /
• pp.1-21
• /
• 2013

The release of IEEE 802.15.4e specification significantly develops IEEE 802.15.4. The most inspiring improvement is the enhancement for medium access control (MAC) sublayer. To study the performance of IEEE 802.15.4e MAC, in this paper we first present an overview of IEEE 802.15.4e and introduce three MAC mechanisms in IEEE 802.15.4e. And the major concern here is the Time Slotted Channel Hopping (TSCH) mode that provides deterministic access and increases network capacity. Then a detailed analytical Markov chain model for TSCH carrier sense multiple access with collision avoidance (CSMA-CA) is presented. Expressions which cover most of the crucial issues in performance analysis such as the packet loss rate, energy consumption, normalized throughput, and average access delay are presented. Finally the performance evaluation for the TSCH mode is given and we make a comprehensive comparison with unslotted CSMA-CA in non-beacon enabled mode of IEEE 802.15.4. It can validate IEEE 802.15.4e network can provide low energy consumption, deterministic access and increase network capacity.

• The Journal of the Acoustical Society of Korea
• /
• v.31 no.7
• /
• pp.441-448
• /
• 2012

Spread spectrum provides the minimized inter-symbol interference, the low probability of intercept and the multiple access capability. This paper presents a direct sequence spread spectrum with carrier/timing recovery and equalizer which compensates the delay spread caused by multipath transmission. When the sea trials were performed in Korean East Sea, the bit error rates of QPSK and direct sequence spread spectrum are $1.46{\times}10^{-2}$ and $5.17{\times}10^{-4}$ at 3 km source-receiver range, respectively.

• Journal of Digital Contents Society
• /
• v.9 no.1
• /
• pp.61-67
• /
• 2008

In this paper, MAC algorithm for the IEEE 802.11 DCF improving the performance is proposed and analyzed by simulation. The MAC of IEEE 802.11 WLAN to control data transmission uses two control methods called DCF(Distributed Coordination Function) and PCF(Point Coordination Function). The DCF controls the transmission based on CSMA/CA(Carrier Sense Multiple Access with Collision Avoidance), that decides a random backoff time with the range of CW(Contention Window) for each station. Normally, each station increase the CW to double after collision, and reduces the CW to the minimum after successful transmission. The DCF shows excellent performance relatively in situation that competition station is less but has a problem that performance is fallen from throughput and delay viewpoint in situation that competition station is increased. This paper proposes an enhanced DCF algorithm that increases the CW to maximal CW after collision and decreases the CW smoothly after successful transmission in order to reduce the collision probability by utilizing the current status information of WLAN. To prove efficiency of proposed algorithm, a lots of simulations are conducted and analyzed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.3
• /
• pp.184-191
• /
• 2018

Orthogonal frequency division multiplexing(OFDM) is a multicarrier modulation(MCM) system that enables high-speed communications using multiple carriers and has advantages of power and spectral efficiency. Therefore, this study aims to complement the existing shortcomings and to design an efficient MCM system. The proposed system uses the inverse discrete wavelet transform(IDWT) operation instead of the inverse fast Fourier transform(IFFT) operation. The bit error rate(BER), spectral efficiency, and peak-to-average power ratio(PAPR) performance were compared with the conventional OFDM system through the OFDM system design based on wavelet transform. Our results showed that the conventional OFDM and Wavelet-OFDM exhibited the same BER performance, and that the Wavelet-OFDM using the discrete Meyer wavelet had the same spectral efficiency as the conventional OFDM. In addition, all systems of Wavelet-OFDM based on various wavelets confirm a PAPR performance lower than that of conventional OFDM.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.9
• /
• pp.1699-1709
• /
• 2015

Moving terminals like high-speed-train undergo high Doppler frequency shift, and this leads to carrier frequency offsets that have to be compensated to avoid degradation of communication performance. In multiple access mechanism like OFDMA, base-stations need complex hardware to compensate the uplink frequency offset. In this paper, we propose a method, which can reduce burden of the base-station and makes frequency offset estimation and compensation simple. This method contains transmitting new synchronization signal, estimating frequency offsets in base-station, transmitting feedback information to terminal, and compensating the offset in uplink transmission. Simulation results show the proposed method operates well in high Doppler frequency shift conditions of 500 km/h which is the requirements of 5G mobile communication.

• Clinical and Experimental Pediatrics
• /
• v.45 no.7
• /
• pp.917-922
• /
• 2002

An unbalanced translocation is frequently the result of inheritance of an unbalanced haploid set from a parent with a balanced translocation. Families in which one parent is a balanced translocation carrier fall into the following classes : Those in which none of the possible abnormal offsprings is viable; Those in which one type of offspring, usually the one with the smaller deletion, is born alive; Those in which two types of abnormal offspring are viable. We report a neonate whose karyotype was 46,XX,der(2)t(2;7)(q21;p21.2),der(20)t(2;20)(q21;p13). She was small for her gestational age and had multiple anomalies such as exophthalmos, corneal opacity, short neck, tongue tie, clinodactyly, atrial septal defect, patent ductus arteriosus and ventriculomegaly. Moreover, her mother's karyotype was 46,XX,der(2)t(2;7)(q21;p21.2),del(16)(q22.1),der(20)t(2;20)(q21;p13) but her father had normal karyotype. The same derivative chrosomes were found between mother and her infant, except for del(16)(q22.1) in her mother and these same unbalanced translocations in a two-generation family are extremely rare.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.5B
• /
• pp.429-436
• /
• 2011

The G-PON is an efficient solution to implement the FTTH and have GEM frame to accomodate various protocols like Ethernet frames, IP packets, and TDM signals. Above all, the Ethernet is one of the most widely used 2nd layer protocol in the campus, the subscriber access, and the carrier service. So G-PON system has to provide an Ethernet interface with top priority. In this paper, we implement a gigabit Ethernet adapter based on Ethernet over GEM in the ITU-T G.984.3 to accommodate Ethernet protocol in the G-PON TC chip. The adapter maps each Ethernet frame to a single or multiple GEM frames and has several functions including generation of the GEM header, encapsulation of frames and the SAR. In particular, the adapter have converter (LUT) MAC address to port-ID which is a key to identify logical connections though it is not defined in specification but important. We implement the adapter with a FPGA and verify the functions of segmentation and reassembling, MAC address learning, and throughput with the logic analyzer and the Ethernet analyzer.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.2
• /
• pp.56-59
• /
• 2011

The characterization of the chemical mechanical polishing (CMP) process for undensified phophosilicate glass (PSG) film is reported using design of experiments (DOE). DOE has been used by experimenters to understand the relationship between the input variables and responses of interest in a simple and efficient way, and it typically is beneficial for determining the appropriatesize of experiments with multiple process variables and making statistical inferences for the responses of interest. The equipment controllable parameters used to operate the machine consist of the down force of the wafer carrier, pressure on the back side wafer, table and spindle speeds (SS), slurry flow (SF) rate, pad condition, etc. None of these are independent ofeach other and, thus, the interaction between the parameters also needs to be understoodfor improved process characterization in CMP. In this study, we selected the five controllable equipment parameters the most recommendedby process engineers, viz. the down force (DF), back pressure (BP), table speed (TS), SS, and SF, for the characterization of the CMP process with respect to the material removal rate and film uniformity in percentage terms. The polished material is undensified PSG which is widely used for the plananization of multi-layered metal interconnects. By statistical modeling and the analysis of the metrology data acquired from a series of $2^{5-1}$ fractional factorial designs with two center points, we showed that the DF, BP and TS have the greatest effect on both the removal rate and film uniformity, as expected. It is revealed that the film uniformity of the polished PSG film contains two and three-way interactions. Therefore, one can easily infer that process control based on a better understanding of the process is the key to success in current semiconductor manufacturing, in which the size of the wafer is approaching 300 mm and is scheduled to continuously increase up to 450 mm in or slightly after 2012.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.12
• /
• pp.1079-1085
• /
• 2013

Due to the limited power supply resources, it is essential that the minimization of algorithmic operation and the reduction of the hardware logical-resources in the design of the satellite transponder. It is also required that the transponder process the signals of various bandwidth efficiently, that is suitble for the SDR-based implementation. This paper proposes a variable rate down sampler which can provide variable bandwidth and data rate for carrier, ranging and sub-band command signals respectively. The proposed down sampler can provide multiple $2^M$ decimated outputs from a single half band filter with recursive arithmetic architecture, which can minimize the hardware resources as well as the arithmetic operations. The algorithm for hardware implementation as well as the analysis for the passband flatness and aliasing is presented and varified by the FPGA implementation.