• 오토저널
• /
• 제11권3호
• /
• pp.29-36
• /
• 1989

A multidimensional numerical simulation for flows in an engine with axisymmetric geometry was performed. Three kinds of differencing schemes, namely, skew upwind differencing scheme (SUDS), interpolated upwind differencing scheme (IUDS), upwind differencing scheme (UDS), are used in a comparative study. Simultaneously, the effects of the artificial dampings and the grids on numerical results are estimated. Compared with the measurements, the calculations with SUDS and proper artificial damping show very similar qualitative tendency with observed results. But there are some discrepancies due to numerical errors and unclear boundary conditions.

• 대한기계학회논문집
• /
• 제16권9호
• /
• pp.1744-1759
• /
• 1992

본 연구에서는 conchas-spray 코드를 근간으로 하여 기관 실린더 내의 난류유 동과 난류연소 현상을 경제적이고 정확하게 해석할 수 있는 다차원 수치해석 프로그램 을 개발하므로, 전기점화 기관의 흡입, 압축, 연소 과정에 대한 수치해석의 가능성을 제시하고, 스월수 0.0, 0.6, 1.2와 2.4의 파라미터 연구를 통하여 스월이 난류유동 및 난류연소에 미치는 영향을 파악하였다.

• 오토저널
• /
• 제13권1호
• /
• pp.66-74
• /
• 1991

A multidimensional numerical simulation of turbulent combustion in a constant volume bomb is implemented to clarify the effects of swirl on combustion. This simulation includes the ICED-ALE numerical technique, the skew-upwind differencing scheme, the modified .Kappa.-.epsilon. turbulence model, and the combustion model of the Arrhenius type and the turbulence-mixing-control type. The calculations of the turbulent combustion with swirl are carried out. It shows that the results agree with the measurements allowably. Therefore, the effects of swirl on turbulent combustion are examined through the parametric study of swirl.

• Nuclear Engineering and Technology
• /
• 제54권9호
• /
• pp.3567-3579
• /
• 2022

This paper provides an assessment of fluid transport and mixing processes inside the primary circuit of the test facility ROCOM through the numerical simulation of Test 2.1 with the system code ATHLET. The experiment represents an asymmetric injection of cold and non-borated water into the reactor coolant system (RCS) of a pressurized water reactor (PWR) to restore core cooling, an emergency procedure which may subsequently trigger a core re-criticality. The injection takes place at low velocity under single-phase subcooled conditions and presents a major challenge for the simulation in lumped parameter codes, due to multidimensional effects in horizontal piping and vessel arising from density gradients and gravity forces. Aiming at further validating ATHLET 3-D capabilities against horizontal geometries, the experiment conditions are applied to a ROCOM model, which includes a newly developed horizontal pipe object to enhance code prediction inside coolant loops. The obtained results show code strong simulation capabilities to represent multidimensional flows. Enhanced prediction is observed at the vessel inlet compared to traditional 1-D approach, whereas mixing overprediction from the descending denser plume is observed at the upper-half downcomer region, which leads to eventual deviations at the core inlet.

• Journal of Mechanical Science and Technology
• /
• 제16권3호
• /
• pp.344-353
• /
• 2002

A reliable computational heat transfer model has been investigated to define the heat transfer characteristics of a spray column direct contact heat exchanger, which is often utilized in the process involving counterflows for heat and mass transfer operations. Most of the previous studies investigated are one-dimensional unsteady solutions based on rather fragmentary experimental data. Development of a multidimensional numerical model and a computational algorithm are essential to analyze the inherent multidimensional characteristics of a direct contact heat exchanger. The present study has been carried out numerically and establishes a solid simulation algorithm for the operation of a direct contact heat exchanger. Operational and system parameters such as the speed and direction of working fluid droplets at the injection point, and the effects of aspect ratio and void fraction of continuous fluid are examined thoroughly as well to assess their influence on the performance of a spray column.

• 자원환경지질
• /
• 제54권2호
• /
• pp.247-257
• /
• 2021

The study area has been contaminated with explosive materials and heavy metals for several decades. For the design of the pump and treat remediation method, groundwater flow before and during groundwater pumping in a contaminated aquifer system was simulated, calibrated, and predicted using a generalized multidimensional hydrological numerical model. A three-dimensional geologic formation model representing the geology, hydrogeology, and topography of the aquifer system was established. A steady-state numerical simulation with model calibration was performed to obtain initial steady-state spatial distributions of groundwater flow and groundwater table in the aquifer system before groundwater pumping, and its results were illustrated and analyzed. A series of transient-state numerical simulations were then performed during groundwater pumping with the four different pumping rates at a potential location of the pumping well. Its results are illustrated and analyzed to provide primary reference data for the pump and treat remediation method. The results of both steady-state and transient-state numerical simulations show that the spatial distribution and properties of the geologic media and the topography have significant effects on the groundwater flow and thus depression zone.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1999년도 춘계 학술대회논문집
• /
• pp.1-10
• /
• 1999

This paper briefly introduces the work done up to 1998 during the past twenty years for numerical modeling of ocean process focussing on the neighbouring seas of Korean Peninsula. Modeling of global ocean dynamics has also been performed as a pathway to understand the regional ocean dynamics. The ocean simulation produces a vast amount of multidimensional multivariate dataset therefore adoption of scientific and technical visualization techniques were essential to properly understand the physics involved.

• 대한토목학회논문집
• /
• 제32권2B호
• /
• pp.123-130
• /
• 2012

천수방정식의 수치모형에 MLP(Multi dimensional Limiting Process)기법을 적용한 후 수치모의를 통해 MLP의 수치 진동 제어 성능을 검증하였다. MLP기법은 2, 3차원에서 기존의 TVD 제어자(limiter)들보다 안정적이며 정확한 수치모의를 가능하게 한다. 다차원에서 정확하고 안정적인 수치모의가 가능하도록 개발된 MLP기법은 압축성 유체를 표현하는 2, 3차원 오일러 방정식에 적용되어 기존의 제어자들에 비해 그 뛰어난 성능이 검증된 바 있다. 하지만 천수방정식에 적용된 예는 없으며, 이에 본 연구는 천수방정식에 MLP를 적용하고 천수방정식 수치모형 검증에 주로 사용되는 수치모의를 통해 MLP의 진동 제어 성능을 검증하였다. 모의 결과, MLP는 2차원 천수방정식에 있어서도 기존의 제어자들과 비교하여 수치진동을 보다 잘 제어하는 것으로 판단된다. MLP 사용으로 인해 불연속면 근처에서 정확도가 향상되었고 수치진동이 발생하지 않아 보다 안정적인 모의가 하게 되었다.

• International Journal of Automotive Technology
• /
• 제6권6호
• /
• pp.579-584
• /
• 2005

Unsteady state free natural gas jets injected from several types of injectors were numerically simulated. Simulations showed good agreements with the schlieren experimental results. Moreover, injections of natural gas in intake manifolds of a single-valve engine and a double-valve engine were predicted as well. Predictions revealed that large volumetric injections of natural gas in intake manifolds led to strong impingement of natural gas with the intake valves, which as a result, gave rise to pronounced backward reflection of natural gas towards the inlets of intake manifolds, together with significant increase in pressure in intake manifold. Based on our simulations, we speculated that for engines with short intake manifolds, reflections of the mixture of natural gas and air were likely to approach the inlets of intake manifolds and subsequently be inbreathed into other cylinders, resulting in non-uniform mixture distributions between the cylinders. For engines with long intake manifolds, inasmuch as the degrees of intake interferences between the cylinders were not identical in light of the ignition sequences, non-uniform intake charge distributions between the cylinders would occur.

• 한국토양환경학회지
• /
• 제1권1호
• /
• pp.89-102
• /
• 1996

지하의 유체 유동 및 물질 변환을 해석하기 위하여 다중다상이론을 이용한 통합 모형을 개발하였다 종합적 지배식은 4개의 상내의 화합물들의 물질 및 힘평형 관계를 고려하여 유도되었다. 복합한 이동 및 변환 현상을 설명하고, 공간적 차원을 변동적으로 나타내기 위하여 관계된 모든 변수 및 식들을 함축적이면서 조직적으로 표현하였다. 도출된 비선형시스템은 다차원 유한요소프로_I램으로서 해를 구하였다. 본 개발된 프로그램은 역동적으로 메모리 용량을 조절하여 일이삼차원 문제를 PC부터 SP2슈퍼컴퓨터까지 여러 종류의 기종에서 해석할 수 있다. 계산시간과 저장용량을 줄이기 위하여 시스템식을 분리시키고, 슈퍼컴의 벡터 및 병렬처리를 이용하여 띠행렬의 해를 구하였다. 유속이 우세한 경우의 수치해석상의 불안정한 문제를 해결하기 위하여 상류가중, 질량묶음, 요소별 파라미터 평가법 등을 적용하였다. 일차원 이동문제에 대하여 유한요소법과 유한차분법의 수치해의 안정성 조건을 검토하였다. 구체적인 지하수 유동 및 오염문제에 대한 모델링 예는 본 논문집의 연계 논문에 수록하였다.