• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.12
• /
• pp.1130-1135
• /
• 2015

The bond pull test is the most widely used technique for the evaluation and control of wire bond quality. The wire being tested is pulled upward until the wire or bond to the die or substrate breaks. The inspector test strength of wire by manually and it takes around 3 minutes to perform the test. In this paper, we develop a 3D vision system to measure 3D position of wire. It gives 3D position data of wire to move a hook into wires. The 3D measurement method to use here is a confocal imaging system. The conventional confocal imaging system is a spot scanning method which has a high resolution and good illumination efficiency. However, a conventional confocal systems has a disadvantage to perform XY axis scanning in order to achieve 3D data in given FOV (Field of View) through spot scanning. We propose a method to improve a parallel mode confocal system using a micro-lens and pin-hole array to remove XY scan. 2D imaging system can detect 2D location of wire and it can reduce time to measure 3D position of wire. In the experimental results, the proposed system can measure 3D position of wire with reasonable accuracy.

• The korean journal of orthodontics
• /
• v.46 no.2
• /
• pp.104-110
• /
• 2016

Objective: Traditional retainers (both metal and fiber-reinforced composite [FRC]) have limitations, and a retainer made from more flexible ligature wires might be advantageous. We aimed to compare an experimental design with two traditional retainers. Methods: In this prospective preliminary clinical trial, 150 post-treatment patients were enrolled and randomly divided into three groups of 50 patients each to receive mandibular canine-to-canine retainers made of FRC, flexible spiral wire (FSW), and twisted wire (TW). The patients were monitored monthly. The time at which the first signs of breakage/debonding were detected was recorded. The success rates of the retainers were compared using chi-squared, Kaplan-Meier, and Cox proportional-hazard regression analyses (${\alpha}=0.05$). Results: In total, 42 patients in the FRC group, 41 in the FSW group, and 45 in the TW group completed the study. The 2-year failure rates were 35.7% in the FRC group, 26.8% in the FSW group, and 17.8% in the TW group. These rates differed insignificantly (chi-squared p = 0.167). According to the Kaplan-Meier analysis, failure occurred at 19.95 months in the FRC group, 21.37 months in the FSW group, and 22.36 months in the TW group. The differences between the survival rates in the three groups were not significant (Cox regression p = 0.146). Conclusions: Although the failure rate of the experimental retainer was two times lower than that of the FRC retainer, the difference was not statistically significant. The experimental TW retainer was successful, and larger studies are warranted to verify these results.

• Journal of Korea Multimedia Society
• /
• v.20 no.3
• /
• pp.511-519
• /
• 2017

This Paper introduces the design and communication method between PLC (Programmable Logic Controller) and Arduino based on MODBUS Protocol. MODBUS connection can be established in a new or existing system very easily, therefore we used this protocol in our proposed system. In the field of automatic devices, multi-function serial port such as RS232, RS422, RS485, and so on creates a great convenience to the developer. This proposed system used RS485 as a key mediator for data exchanging on a connected network. We also believe that it will reduce the development cost in various automated industry because this system can be reused or can be implemented any such PLC installed machines. RS485 is used as a communication interface between PLC (as a slave) and Arduino (as a master), through which a reliable network is created for safe and fast communication. Furthermore, RS485 allows multiple devices(up to 32) to communicate at half duplex on a single pair of wires and provides a long connectivity area (up to 1200 meters) as compare to other device, which makes it a user-friendly for various devices in the automated industry. Moreover, Arduino can play as a mediator by connecting third party device and setup a communication network with PLC.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.587-590
• /
• 2012

Recently, the demand for the miniaturization of package substrates has been increasing. Technical innovation has occurred to move package substrate manufacturing steps into CMP applications. Electroplated copper filled trenches on the substrate need to be planarized for multi-level wires of less than $10{\mu}m$. This paper introduces a chemical mechanical planarization (CMP) process as a new package substrate manufacturing step. The purpose of this study is to investigate the effect of surfactant on the dishing and erosion of Cu patterns with the lines and spaces of around $10/10{\mu}m$ used for advanced package substrates. The use of a conventional Cu slurry without surfactant led to problems, including severe erosion of $0.58{\mu}m$ in Cu patterns smaller than $4/6{\mu}m$ and deep dishing of $4.2{\mu}m$ in Cu patterns larger than $14/16{\mu}m$. However, experimental results showed that the friction force during Cu CMP changed to lower value, and that dishing and erosion became smaller simultaneously as the surfactant concentration became higher. Finally, it was possible to realize more globally planarized Cu patterns with erosion ranges of $0.22{\mu}m$ to $0.35{\mu}m$ and dishing ranges of $0.37{\mu}m$ to $0.69{\mu}m$ by using 3 wt% concentration of surfactant.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.9
• /
• pp.28-43
• /
• 1999

In this paper, we present a gridless router for MultiChip Modules (MCM). Because our router uses corner stitching data structures, not a routing grid, to represent the routings status, it allows arbitrary location of pins, and routes variable-width wires, without a considerable waste of area from bulky vias. A routing speed is a very important factor because a gridless routing approach is known its computation is hard and complex, and MCM routing problem has so large routing area and layers. Our router completes the routing faster than the most of previously reported grid-based routers, with comparable routing result, by using SEGRAs routing algorithm whose very fast speed is proved, and the characteristics of the effective data structure.

• Journal of Navigation and Port Research
• /
• v.31 no.10
• /
• pp.833-837
• /
• 2007

In this study, we have fabricated a gain flattened erbium-doped optical fiber amplifier. Gain flattening filters were realized by the strain-induced long period fiber gratings, which are made of periodically arrayed metal wires. Using the filter of $550{\mu}m$ period, spontaneous emission amplified at C-band wavelength by a 980nm pumping laser was flattened within 1dB of gain ripple. The performance of the simultaneous multi channel amplification was measured using a fabry-perot laser diode. Amplification ratio was above 20dB. This amplifier can be applied to the long distance transmission system based on a wavelength division multiplexing for boosting an attenuated signal.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.3
• /
• pp.70-79
• /
• 2020

The main objective of this research to develop an IoT based wireless contactless ultrasonic system (ICUS) and its application to concrete structure. The developed system consists of 16 mems, 2Mhz digitizer, amplifying circuit, FPGA, and wifi module, enabling to measure leaky surface waves from concrete specimens without physical coupling process and wires. Multi-channel analysis is performed to improve the accuracy of data analysis, and the velocity of leaky surface waves and acoustics are derived. Field inspection of railroad concrete sleepers is conducted to evaluate the performance of the system and to compare the results with conventional ultrasonic pulse velocity (UPV). As a result of the field inspection, UPV was limited to evaluate damages. This is because crack pattern of railroad sleepers is parallel to ultrasonic ray path and accessibility of the railroad at the field is disadvantageous to contact-based UPV. On the other hand, ICUS possibly detect the damages as reduction of dynamic modulus by up to 59% compared to non-damaged specimen.

• Journal of Welding and Joining
• /
• v.31 no.6
• /
• pp.84-89
• /
• 2013

The demand of LNG tank and the constituting material, i.e., the Al5083 thick plate, increased due to the rapid growth LNG market. To weld the Al5083 thick plate, the gas metal arc welding (GMAW) of high current is necessary to increase manufacturing productivity incurred by the multi pass welding. However, the arc welding vaporizes the volatile element such as magnesium (Mg). This phenomenon changes the Mg composition of the weld metal and the mechanical properties. The study investigated the weldability of Al5083 alloys after conducting high current GMAW. The Al5083 alloy was welded by using different size of welding wires and high current (800-950A). As the arc current increased from 800A to 950A, the mechanical strength decreased and the secondary dendrite arm spacing (SDAS) increased. Even though the arc current increased SDAS, the mechanical strength decreased due to the Mg loss in the weldment. The large diameter of welding wire decreased the dilution of the weld, therefore increasing the Mg content and the strength of the weld. For the reason, the content of Mg in welds was a major parameter to determine the mechanical property for the high current GMAW. For the arc current between 800A and 950A, the yield strength of the weldments showed a relationship with the weight percent of Mg content ($X_{Mg}$): Y.S = 27.9($X_{Mg}$)-11.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.2
• /
• pp.254-259
• /
• 2008

Mesh WLANs, which consist of wireless mesh routers connecting each other in a mesh topology and self-operate after their autoconfiguration, have several advantages in convenience, swiftness and flexibility of deployment and operation over existing WLANs the expansions of which are done by connecting the APs with wires. However, many technical issues still remain to be solved. Among them, network performance degradations due to the interference between the adjacent hops in multi-hop mesh WLANs, and the reusability of the existing wireless network protocols are critical problems to be answered. This work evaluates the VoIP support performance of IEEE 802.11a/g-based mesh WLANs with multiple wireless interfaces with simulations. The results show that there exit an unfairness in VoIP packet delay performances among mobile routers located at different hops, and that although the capacity of the admitted calls can be increased by increasing the size of voice packet payload it is far less than the expected one. This suggests that the existing 802.11 MAC protocols have their limitation when applied in mesh networks and their enhancement or even a newer one nay be required.

• Imaging Science in Dentistry
• /
• v.52 no.2
• /
• pp.155-164
• /
• 2022

Purpose: The aim of this study was to systematically screen the literature for studies reporting cosmetic material in the oral and maxillofacial complex to shed light on the types of cosmetic materials, their radiographic appearance, and possible complications. Materials and Methods: Five electronic databases were reviewed for eligible studies. The general search terms were "cosmetic," "filler," "face," and "radiograph." Demographics, material types, clinical and radiographic presentation, and complications were recorded. Results: Thirty-one studies with 53 cases met the inclusion criteria. The mean age was 52.6±15.4 years with a 4 : 3 female-to-male ratio. The most common material was calcium hydroxyapatite (CaHa) (n=14, 26.4%), found incidentally. The materials were generally located within the upper cheek and zygoma (n=35, 66.0%), radiographically well-defined (n=44, 83%), and had no effects on the surrounding structures (n=27, 50.9%). The internal structure was radiopaque (calcification, hyperdensity) for gold wires, CaHa, bone implants, and secondary calcification or ossification. Outdated cosmetic materials or non-conservative techniques were infiltrative, had effects on the surrounding structures, and presented with clinical signs, symptoms, or complications. Conclusion: Conventional radiography, cone-beam computed tomography, and multi-detector computed tomography are useful to differentiate several cosmetic materials. Their magnetic resonance imaging appearance was highly variable. The infrequent inclusion of cosmetic materials in the differential diagnosis implies that medical and dental specialists may be unfamiliar with the radiographic appearance of these materials in the face.