• 한국레이저가공학회지
• /
• 제17권3호
• /
• pp.15-18
• /
• 2014

In this paper, we studied a machining method using a diffractive beam splitter (DBS) and multi- pulse repeated radiation for breathable film. We fabricated micro-grooves on polypropylene (PP) films using multi-pulse radiation and one-shot radiation (radiating pulses at once) and a DBS. In the result, width and depth of the PP film using multi-pulse repeated radiation were more precisely controllable. Therefore, this method can be applicable to in manufacturing breathable film precisely at a high speed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.1056-1059
• /
• 2001

These days, as dynamic function and special properties to compare traditional material, $Al_20_3$ ceramic use all over the industry. But it is very difficult to process because of high hardness and brittleness. Therefore, in this paper, it was investigated that laser process parameter which can produce appropriate quality of $Al_20_3$ ceramic microhole machining.

• 대한기계학회논문집A
• /
• 제33권5호
• /
• pp.496-501
• /
• 2009

In micro electrochemical machining(micro-ECM), it is important to measure and control the potential of a tool electrode and a workpiece electrode because electrochemical reaction rate depends on the potential of the electrodes. When the electrode potential was measured against a reference electrode, the error of measured electrode potential could be minimized by proper tool electrode design. In this paper, multi-function electrodes consisting of a tool electrode and a reference electrode was fabricated by micro fabrication techniques. The machining conditions in micro-ECM using multi-function electrodes, such as pulse voltage parameters and electrode potential, were investigated.

• 한국자기학회지
• /
• 제13권3호
• /
• pp.115-120
• /
• 2003

스퍼터링 방법으로 FM/M/FM의 다층박막을 증착한 다음 초소형 박막 인덕터를 제작하기 위하여 반도체 공정을 대체할 수 있는 레이저 미세가공 기술을 개발하였다. TE $M_{00}$ 모드로 발진하는 CW Nd:YAG 레이저를 active Q-switching 하여 펄스폭이 200 ns인 극 초단 레이저 펄스를 얻었다. 레이저 미세가공 조건을 반복율 5 kHz, 펄스 당 에너지 5 mJ/pulse로 최적화 하여 분해능이 20 $\mu\textrm{m}$인 line patterning을 얻었다.

• Journal of Mechanical Science and Technology
• /
• 제17권6호
• /
• pp.816-824
• /
• 2003

In this study, variations of cutting performance with pulse time, open circuit voltage, wire speed and dielectric fluid pressure were experimentally investigated in Wire Electrical Discharge Machining (WEDM) process. Brass wire with 0.25 mm diameter and AISI 4140 steel with 10 mm thickness were used as tool and work materials in the experiments. The cutting performance outputs considered in this study were surface roughness and cutting speed. It is found experimentally that increasing pulse time, open circuit voltage, wire speed and dielectric fluid pressure increase the surface roughness and cutting speed. The variation of cutting speed and surface roughness with cutting parameters is modeled by using a regression analysis method. Then, for WEDM with multi-cutting performance outputs, an optimization work is performed using this mathematical models. In addition, the importance of the cutting parameters on the cutting performance outputs is determined by using the variance analysis (ANOVA).

• 한국세라믹학회지
• /
• 제42권6호
• /
• pp.377-383
• /
• 2005

Generally, the strength achieved of glass-ceramics is higher as is the fracture toughness, as compared with the original glass. This improvement is due to the microstructure consisting of very small crystals. In this study, Ag-doped $45SiO_2-24CaO-24Na_2O-4P_2O_5$ glasses were irradiated to strengthen by the crystallization using Femto second laser Pulses. Through the UV/VIS spectroscope, XRD, Nano-indenter and SEM etc., heat-treated and irradiation of laser pulses without heat-treated samples were analyzed. Two kinds of samples, heat-treated and laser irradiated without heat-treated samples, showed the peaks in the same wavelength near 360 nm. Especially, samples irradiated by 140 mW laser with XYZ stage having at the rate of 100$\~$l000 $\mu$m/s had the largest absorption peak among them, and heat-treated samples was shown lower absorption range than over 90 mW laser irradiated samples. Moreover, samples irradiated by laser had higher values ($4.4\~4.56{\times}10^{-3}(Pa)$) of elastic modulus which related with strength of glass than values of heat-treated samples and these are 1.2$\~$1 .5 times higher values than them of mother glass.