• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.9 s.252
• /
• pp.842-849
• /
• 2006

An experimental study has been conducted to investigate the effects of a multi air-staged burner on NOx formation and heat transfer in a 15kW large-scale laboratory furnace adopted the reburning process. The reburn fuel as well as burnout air was injected from each nozzle attached at the wall of the cylindrical furnace. Fuel in both main burner and reburn nozzle was LPG (Liquefied Petroleum Gas). The paper reports the influences on NOx reduction of reburn fuel fraction in reburning zone. Temperature distribution inside the overall region as well as total heat flux at the wall of the furnace has been measured to examine the heat transfer characteristics due to the reburning process. For comparison, the reburning effects were examined for a combustor with two types of burner; a regular single staged burner and a multi-air staged burner. A gas analysis was also performed to evaluate an appropriate condition for NOx emission in a primary zone for the excess air ratio of 1.1. As a result, combustion efficiency expected to become more efficient due to the reduction of heat loss in burnout zone decrease when multi air-staged burner in furnace adopted reburning technology was used.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.4
• /
• pp.585-595
• /
• 2008

Process design of multi-stage forging for a bolt with nonaxisymmetric washer cam has been studied by using finite element method. For shape complexity of the bolt, it is impossible to manufacture in a single stage forging. To design multi-stage forging for the bolt the forging load and fiber flow of each step have been analyzed by using commercial finite element code DEFORM-3D. Simulated results have been compared with experimental ones. Multi-stage forging process has been designed with four stages. The workpiece should be eccentric shape until third forging stage. And then bolt head and washer of eccentrical shape is created in last stage. As a results, It was predicted that shape of product would be good and effective strain would be uniformly distributed in the product. Also, it was predicted whether defects would exist or not by reviewing the fiber flow.

• Transactions of Materials Processing
• /
• v.24 no.3
• /
• pp.187-193
• /
• 2015

The objective of the current study is to determine cross-sectional profile of intermediate dies in order to improve the plastic strain homogeneity which directly affects not only the dimensional accuracy but also the mechanical properties of final product by redesigning the intermediate dies using the conventional electric field analysis (EFA) method. Initially, the multi-pass shape wire drawing was designed by using the equivalent potential lines from EFA. The area reduction ratio was calculated from the number of passes in multi-pass shape wire drawing but constrained by the capacity of the drawing machine and the drawing force. In order to compensate for a concentration of strain in a region of the cross section of the wire, the process for multi pass wire drawing from initial round material to an intermediate die was redesigned again using the electric field analysis. Both drawing process designs were simulated by the finite element method in which the strain distribution and standard deviation plastic strain of the cross section of drawn wires were examined.

• Transactions of Materials Processing
• /
• v.17 no.3
• /
• pp.170-181
• /
• 2008

The shape of rectangular cup used for Ni-MH(Nickel-coated Metal Hydrogen) battery for hybrid car looks quite simple, but the forming process of extruding and setting up process design are highly difficult. Furthermore, there are few concrete reports on the rectangular deep drawn cup as part of hybrid vehicles till now. In this study, process design for rectangular cup in the multi-stage deep drawing process is carried out, and FE analysis is also preformed based on the result of the process design. From the simulation result, some unexpected problems such as earing, wrinkling and excessive thickness changes of the intermediate blank occurred. To overcome these failures, a series of modification for punch shape in the forming process design are completed and applied. Considering the modified punch shape in the multi-stage deep drawing process, additional FE analysis is also carried out and the simulation result is verified in view of the deformed shape, thickness change and effective strain distribution. The result of FE analysis with the improved process design confirmed not only reducing thinning of wall and possibilities of failure but also improving the quality of drawing product through the modification of punch shape.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.1
• /
• pp.3-8
• /
• 2006

This paper deals with an automated computer-aided process planning and die design system by which designer can determine operation sequences even if they have a little experience in process planning and die design for axisymmetric products. An attempt is made to link programs incorporating a number of expert design rules with the process variables obtained by commercial FEM softwares, DEFORM and ANSYS, to form a useful package. The system can provide a flexible process based on either the reduction in the number of forming sequences by combining the possible two processes in sequence, or the reduction of deviation of the distribution on the level of the required forming loads by controlling the forming ratios. Especially in die design module optimal design technique and horizontal split of die insert were investigated for determining appropriate dimensions of components of multi-former die set. Results obtained, using the modules, enable the design and manufacture of a die set for a multi-former to be more efficiently performed.

• Korean Journal of Agricultural Science
• /
• v.38 no.1
• /
• pp.183-190
• /
• 2011

The paper is to analyze multi-attributes for expanding new renewable energy in agricultural sectors which have environmental, technical, economic, and social factors consisting of 15 attributes which have both positive and negative impacts. We applied the analytic hierarchy process (AHP) to data from opinion polls. As a result of the AHP survey, the overall results indicate that the respondents more weight on economical factor than environmental, technical, and social factors for expanding new renewable energy. At the lowest level, a comparison of individual 15 attributes within three factors shows that fixed cost highest in multi-attributes, followed by operating cost, technical superiority. To achieve the public acceptance about expanding new renewable energy in agricultural sectors, the policy-makers should take all relevant factors into account through the decision-making process by the public opinions.

• Elastomers and Composites
• /
• v.52 no.4
• /
• pp.272-279
• /
• 2017

The heterocoagulation of latex is a simple and useful method to fabricate various polymer nanocomposites in which a precise control of the colloid stability is essential. In this work, a multi-layered graphenes (MLGs)/poly(styrene-co-butyl acrylate) (P(S-co-BA)) nanocomposite having an excellent dispersion of MLGs was prepared via the sudden heating heterocoagulation process. The P(S-co-BA) component was obtained by emulsion polymerization. This process can effectively shorten the process and particles growth steps. The colloid stability of these dispersions was controlled by factors such as ionic charge, temperature, and reaction times. The influence of these factors on heterocoagulation was evaluated and the properties of the nanocomposites were investigated. The conductivity of the MLGs/P(S-co-BA) nanocomposites increased from -11.53 to -5.70 S/cm for an increase in MLG content from 0.01 to 5 wt%. Moreover, percolation threshold was observed in the case of 0.01 wt% MLGs.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.05a
• /
• pp.85-88
• /
• 2001

Examination of the die design is carried out for a multi-stage rectangular cup drawing process with the large aspect ratio with the aid of the finite element analysis. The analysis considers the deep drawing process with the ironing process for the thickness control in the cup wall. Simulation is performed to investigate the deformation mechanism in the initial design and the modified design. The analysis clarifies that the irregular cross section and the irregular contact condition produces unfavorable deformation. The analysis results show that the modified design improves the quality of a deep-drawn product with the low possibility of failure. The analysis result also shows good agreement with the experimental one.

• Transactions of Materials Processing
• /
• v.29 no.2
• /
• pp.97-102
• /
• 2020

Wire drawing is a metalworking process used to reduce the cross-section of a wire by pulling the wire through multi-stage drawing dies. The aim of this study is to fabricate a drawing wire using 2 stage drawing process. The finite element analysis of wire drawing was conducted to validate the efficiency of the designed process and the experiment was performed to validate the designed wire drawing process using 2 stage tungsten carbide die. Dry lubricant with powder was applied for producing a wire of desired diameter. Finally, a drawing wire using 2 stage die for cold rolling mill was developed.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.6
• /
• pp.97-103
• /
• 2008

In this paper, the Post Process for the manifold complex processing using CAD/CAM Software of two and a half Dimensions(2.5D) has been developed to maximize the application of the manifold manufacturing machine. Many companies are currently making use of high price systems to improve manufacturing process using the multi-axial complex manufacturing machine. In accordance with the requirements, the utilization of CAD/CAM Software for the manifold complex manufacturing machine is earnestly demanded. However, the experts who have experience in manifold manufacturing machine are insufficient. Consequently the outcomes of the Post Process for 2.5D CAD/CAM Systems have been dealt in order to be smoothly operated by those who have basic skills and be understood in process drawings. CNC program functions can be specially used as they are, when drawn up. The Post Process for the original point designation and transformation of coordinates has been developed and applied. The results gave proof of practical manufacturing outcomes.