• 대한기계학회논문집
• /
• 제18권11호
• /
• pp.2817-2824
• /
• 1994

A torque split type multi-pass CVT(MPC) system consiting of CVT and planetary gear train with 4 clutches was suggested to overcome the inherent inferior acceleration performance of CVT. Also, a shifting algorithm of MPC was suggested for the two driving modes : (1) power mode and (2) economy mode. By using the shifting algorithm and the MPC vehicle dynamic model, numerical simulations were performed to estimate the performance of the MPC vehicle. Simulation results showed that comparing the performance of the conventional 4-speed automatic transmission, an improvement in acceleration can be obtained by MPC for the power mode and 31% improvement in fuel economy for the economy mode.

• Journal of Mechanical Science and Technology
• /
• 제18권1호
• /
• pp.114-121
• /
• 2004

In order to investigate the corrosion fatigue characteristics in the weld of multi-pass welded A 106 Gr B steel pipe, corrosion fatigue tests were performed under the various stress ratios and 3.5 wt% NaCl solution at room temperature. The corrosion fatigue characteristic curves were represented using crack closure concept. The obtained results are as follows : when the load frequency is 1.0 Hz, the crack opening point is transited in the region of $K_{max}$=20∼32 MPaㆍ $m^{1}$2/. In the low stress intensity factor range, the crack opening point is higher than that in air. However, in the high stress intensity factor range, it is lower than that in air. In the cases of 0.1 Hz and 0.01 Hz, the crack opening point gradually decreases to $K_{min}$ with $K_{max}$ increase.rease.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.730-735
• /
• 2000

The finite element analysis by the computer program SYSWELD in consideration of phase transformation was carried out to simulate the multi-pass welding process of SA106 Gr. C which is used for the main steam pipe in nuclear power plant. All the numerical results such as temperatures, the size of heat affected zone and the residual stresses were compared to the experimental results.

• 소성∙가공
• /
• 제21권5호
• /
• pp.291-297
• /
• 2012

In this paper, the effect of back tension in multi-pass drawing or wiredrawing on the central bursting defect is investigated using finite element predictions. A rigid-plastic finite element method was used together with the McClintock damage model. Central bursting defects under different back tension stress values ranging from 0% to 20% of the yield strength of the material were predicted and they were compared to understand the effect of the back tension stress values on the central bursting defect. It is found that the level of back tension has a strong influence on the cumulative damage. Thus, higher back tension raises the possibility of the central bursting defect occurring, even though it decreases the interfacial pressure between the die and the work piece.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.139-142
• /
• 2005

Cu-Ni-Zr-Ti bulk amorphous thin strips were produced by multi-pass warm rolling of the amorphous powder at temperatures in the supercooled liquid region. Process variables for rolling of the bulk amorphous strips were properly controlled to prevent onset of crystallization and failure during rolling up to three passes. During rolling of the amorphous powder, both the deformation and densification took place and the newly developed surface on the deformed amorphous particles enhances the consolidation leading to an increase in the strength. The strain state during rolling was analyzed by FEM.

• 한국정밀공학회지
• /
• 제20권3호
• /
• pp.194-201
• /
• 2003

This study presents the comparative filtration performance evaluation of automotive fuel filters based on the theory of Beta ratio. For the experiments, the fuel component's test stand incorporating the multi-pass filtration test circuit was developed. A mathematical description of filtration process in general was derived. And the theoretical basis of multi-pass test and the test procedure were described in detail. Experimental results revealed that domestic fuel filter tested could not maintain consistent Beta ratio, that is filtration efficiency, although it had the holding capacity of contaminants close to the specification at maximum pressure drop across the filter assembly. The results of experiments and simulations also showed that filtration system model could be refined including desorption ratio to estimate the variable Beta ratio in service life.

• 한국전자통신학회논문지
• /
• 제5권2호
• /
• pp.180-184
• /
• 2010

본 논문에서는 다중 채널 심장 전기도 주 증폭기의 중요한 부분인 필터를 설계하고 시뮬레이션을 통하여 성능을 분석하였다. 주 증폭기는 샘플/홀더, 가변 고역통과 필터, 노치 필터, 가변 저역통과 필터로 구성된다. 필터는 기존의 64 채널의 공간 분해능을 향상시키기 위하여 128채널을 고려하여 설계되었다.

• 한국재료학회지
• /
• 제21권6호
• /
• pp.320-326
• /
• 2011

Flat rolling of wire is an industrial process used to manufacture electrical flat wire, medical catheters, springs, piston segments and automobile parts, among other products. In a multi-step wire flat rolling process, a wire with a circular crosssection is rolled at room temperature between two flat rolls in several passes to achieve the desired thickness to width ratio. To manufacture a flat wire with a homogeneous microstructure, mechanical and metallurgical properties with an appropriate pass schedule, this study investigated the effect of each pass schedule (1stand ~ 4stand) on the microstructures, mechanical properties and widths of cold rolled high carbon steel wires using four-pass flat rolling process. The evolutions of the microstructures and mechanical properties of the widths of cold rolled wires during three different pass schedules of the flat rolling process of high carbon wires were investigated, and the results were compared with those for a conventional eight-pass schedule. In the width of cold rolled wires, three different pass schedules are clearly distinguished and discussed. The experimental conditions were the same rolling speed, rolling force, roll size, tensile strength of the material and friction coefficient. The experimental results showed that the four-pass flat cold rolling process was feasible for production of designed wire without cracks when appropriate pass schedules were applied.

• 한국ITS학회 논문지
• /
• 제13권4호
• /
• pp.30-37
• /
• 2014

단차로 하이패스시스템의 지 정체로 인한 교통 혼잡, 안전사고, 유지보수 등 매년 발생하는 문제를 해결하기 위해 무정차 다차로 고속주행기반 시스템의 개발이 필요하게 되었다. 하이패스 통신시스템은 단차로 환경에서 선입선출 방식이므로, 다차로 환경에서 발생하는 군집주행 및 차로전환 등 다양한 주행패턴을 처리할 수 없다. 본 논문에서는, 기존의 하이패스 단말기를 수용하면서 다차로 주행이 가능한 통신시스템을 개발했다. 능동형 RF/IR 통신 안테나를 이용해 중첩 영역은 넓히고, 오류범위를 최소화 하는 기술을 구현했다. 체험도로를 다차로 실 환경처럼 구축하여 테스트한 결과 하이패스시험기준을 통과했을 뿐 아니라, 속도별, 차로별, 차로전환별 주행시험 및 단말기 위치별 시험 결과 통신 정확도도 99.9%로 하이패스시스템의 성능을 만족했다. 무정차 다차로를 위한 통신시스템은 향후 고속도로 및 유료도로에서도 사용할 수 있을 뿐 아니라, 주차장에서도 활용할 수 있을 것으로 기대한다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 제4회 압출 및 인발가공 심포지엄
• /
• pp.37-44
• /
• 2001