• Journal of the Korean Ceramic Society
• /
• v.31 no.10
• /
• pp.1115-1122
• /
• 1994

ZT/PZT/ZT multi-layered thin films were deposited on silicon substrate by co-sputtering method for FEMFET device application. Effects of Pb/(Zr+Ti) ratio, films thickness, annealing conditions and substrate temperature on the ferroelectric behavior of the multi-layered films were studied. The best memory device characteristics with leakage current of 2$\times$10-8 A/$\textrm{cm}^2$ and breakdown field of about 1 MV/cm could be obtained with ZT(250 $\AA$) / PZT(1000 $\AA$)/ZT(750 $\AA$) multi-layered thin film deposited at 35$0^{\circ}C$ and post-annealed at $700^{\circ}C$ for 120 sec by RTA(Rapid Thermal Annealing).

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1129-1132
• /
• 1995

In the preparation of the layered $BaTiO_3$ thin films with high performance, the new stacking method using the continuous cooling of the substrate was introduced. Amorphous/polycrystalline $BaTiO_3$ layered structure was confirmed by SEM and index of refraction. The layered $BaTiO_3$ thin films formed by the new stacking method showed such a high dielectric constant that the layered structure could not be explained by a stacking structure of the two defined layers but could only be explained by multi-layered structure, i.e. amorphous/micro crystalline/polycrystalline structure. The layered $BaTiO_3$ thin film with a thickness of 240 nm showed higher capacitance per unit area and breakdown strength than the double layered $BaTiO_3$ thin film prepared by the conventional stacking method. And well defined ferroelectric hysteresis leer was observed in the layered $BaTiO_3$ thin film with a thickness of 200 nm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.5
• /
• pp.426-430
• /
• 2000

We have studied the field emission characteristics of multi-layered diamond-like-carbon (DLC) films deposited by vertical electrodes type plasma enhanced chemical vapor deposition with CH$_4$ and H$_2$ mixture. We deposited a thin layer of DLC on the p$^{+}$-Si substrate and then turned off plasma before another deposition of a new DLC layer. The thickness and the number of DLC layers are varied. The emission characteristics of multi-layered DLC films were compared with conventional one. The multi-layered DLC film shows higher emission current than conventional one.e.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.2
• /
• pp.183-188
• /
• 2003

The micro-patterning of multi-layered thin films containing CdS and $Ta_2O_5$ layers on ITO substrate with various structures was successfully obtained by combining three different techniques: chemical solution depositions, sol-gel, and microcontact printing (μCP) methods using octadecyltrichlorosilane (OTS) as the organic thin layer template. $Ta_2O_5$ layer was prepared by sol-gel casting and CdS one obtained by chemical solution deposition, respectively. Parallel and cross patterns of multi-layers with $Ta_2O_5$ and CdS films were fabricated additively by successive removal of OTS layer pre-formed. This study presents the designed architectures consisting of the two types of feature having horizontal dimensions of 170 ㎛ and 340 ㎛ with constant thickness ca. 150 nm of each deposited materials. The thin film lay-out of the cross-patterning is composed of four regions with chemically different layer compositions, which are confirmed by Auger electron microanalysis.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.189.1-189.1
• /
• 2013

Titanium dioxide (TiO2) is a wide bandgap semiconductor possessing photochemical stability and thus widely used for photocatalysis. However, enhancing photocatalytic efficiency is still a challenging issue. In general, the efficiency is affected by physio-chemical properties such as crystalline phase, crystallinity, exposed crystal facets, crystallite size, porosity, and surface/bulk defects. Here we propose an alternative approach to enhance the efficiency by studying interfaces between thin TiO2 layers to be stacked; that is, the interfacial phenomena influencing on the formation of porous structures, controlling crystallite sizes and crystallinity. To do so, multi-layered TiO2 thin films were fabricated by using a sol-gel method. Specifically, a single TiO2 thin layer with a thickness range of 20~40 nm was deposited on a silicon wafer and annealed at $600^{\circ}C$. The processing step was repeated up to 6 times. The resulting structures were characterized by conventional electron microscopes, and followed by carrying out photocatalytic performances. The multi-layered TiO2 thin films with enhancing photocatalytic efficiency can be readily applied for bio- and gas sensing devices.

• Korean Journal of Metals and Materials
• /
• v.49 no.2
• /
• pp.192-196
• /
• 2011

The multi-layered thin film with an ITO/Ag/ITO structure was produced on PET by using magnetron reactive sputtering method. First, 30 nm of ITO thin film was coated on PET by using normal temperature process. Then 20-52 nm of the Ag thin film was coated. Lastly, 30 nm of ITO thin film was coated on Ag layer. The sample of the 20 nm Ag thin film showed more than 70% transmission and a $2.7{\Omega}/{\Box}$ sheet resistance. When compared to the existing single-layered transparent conducting thin film, multi-layered film was found to be superior with about $5{\Omega}/{\Box}$ less sheet resistance. However, since the Ag layer became thinner, the band gap energy needs to be increased to more than 3.5 eV.

• Korean Journal of Optics and Photonics
• /
• v.12 no.5
• /
• pp.394-400
• /
• 2001

We studied thermal diffusion properties diffusion properties of multi-layered Ge-Sb-Te alloy thin films for optical recording media by solving the thermal equation. Based on the numerical analysis of optical energy distribution and absorption inside multi-layered films including temperature gradient and heat transfer simultaneously, we proposed the optimum parameters of the input laser power and the multi-layer structure as follow. i) Input laser power is 18 mW, ii) laser exposure time is 60 ns, iii) the thicknesses of the lower and the upper ZnS-SiO$_2$are 140 nm and 20~30 nm respectively, and iv) thickness of Ge-Sb-Te recording film is 20 nm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.535-536
• /
• 2008

Multi-layered thin films of ZnS/$Na_3AlF_6$/ZnS/Cr were deposited on glass substrate by evaporation process. ZnS and $Na_3AlF_6$ were selected as high and low refractive index material, and additionally Cr was chosen as mid reflective layer respectively. The multi-layered thin films were prepared in terms of different optical thickness and different staking sequence and layers. The optical properties were systematically characterized with different optical thickness of $Na_3AlF_6$ especially $0.25\lambda$ and $0.5\lambda$. In order to expect the experimental result, the simulation program, the Essential Macleod Program(EMP) was adopted. Based on the results taken by spectrophotometer at viewing angle $45^{\circ}$, the ZnS/$Na_3AlF_6$/ZnS/Cr multi-layered thin film shows purple colour range in $0.25\lambda$， bluish green in $0.5\lambda$, red purple in $0.75\lambda$, and purple in $1.0\lambda$ respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.4
• /
• pp.376-380
• /
• 2008

The optical properties of multi layered thin films with $Sb_2O_3/Na_3AlF_6/Sb_2O_3/Cr$ were simulated by using EMP(Essential Macleod Program). EMP is a comprehensive software package to design and analyse the optical characteristics of multi-layered thin film. $Sb_2O_3$ and $Na_3AlF_6$ were selected as a high refractive index and low refractive index material respectively. Additionally Cr was chosen as mid reflective material. Optical properties including color effect were systematically studied in terms of different optical thickness of low refractive index material. The optical thickness of $Na_3AlF_6$ was changed as 0.25, 0.5, 0.75 and $1.0\lambda$. The film with 0.25, 0.5, 0.75 and $1.0\lambda$ of optical thickness showed mixed color range between purple and red range, yellowish green and bluish green, purple and mixed color range of green and purple respectively.

• Journal of Surface Science and Engineering
• /
• v.48 no.4
• /
• pp.169-173
• /
• 2015

$CuInSe_2$ thin films which have been widely used for thin solar cells as a light absorber were prepared by hydrazine solution processing, and their microstructural properties were investigated. Hydrazine $CuInSe_2$ precursor solutions were prepared by dissolving $Cu_2S$, S, $In_2Se_3$ and Se powder in hydrazine solvent. Multilayer $CuInSe_2$ chalcopyrite phase thin films were prepared by repeating spin-coating process using the precursor solution. Unfortunately, the presence of the interfaces between each $CuInSe_2$ layer formed by multi-layer coating impeded grain growth across the interface. Here, by doing simple interface engineering to solve the limited grain growth issue, the large grained (${\sim}1{\mu}m$) $CuInSe_2$ thin films were obtained.