• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.176-179
• /
• 2001

When the preform is composed of more than two layers with different in-plane permeability in resin transfer molding, effective average permeability should be determined for the flow analysis in the mold. The most frequently used averaging scheme is the weighted average scheme, but it does not account for the transverse flow between adjacent layers. A new averaging scheme is proposed predicting the effective permeability of the multi-layered preform, which accounts for the transverse flow effect. The new scheme is verified by measuring the effective permeability of the multi-layered preforms and the difference in each flow front position.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.175-180
• /
• 2006

The acoustical properties of multi-layered treatments of materials used in applications, such as automotive liners, generally cannot be directly measured by a one-time test in a standing wave duct. Therefore, we have to consider predicting them by the four-pole transfer matrix method. This method requires performing TCM or TLM for measuring the transfer matrix of each layer and calculating the total transfer matrix of the whole multi-layered material. The final predicted absorption ratios and transmission losses of the multi-layered treatments strongly depend on the measured transfer matrix of each layer. All these functions have been included in a new designed acoustical software.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.190-193
• /
• 2004

This paper presents studies on the creation time of scanning path using rapid prototype device. In the case of Jewellery, it needs to take time too much at the whole process of rapid prototype in accordance with heigh of the multi-layered. When increases the number of polygon by heigh of the Multi-layered, it has proper influence on the creation time of scanning path. Therefore, we can get the spending time and the number of polygon for the creation during increase the heigh of the multi-layered. These values are showed by the quantitative. We try to analyze relation between these and heigh of the multi-layered.

• Journal of Electrical Engineering and Technology
• /
• 제4권4호
• /
• pp.531-537
• /
• 2009

Lightning has a broad frequency spectrum from DC to a few MHz. Consequently, the high frequency performance of grounding systems for protection against lightning should be evaluated, with the distributed parameter circuit model in a uniform soil being used to simulate grounding impedances. This paper proposes a simulation method which applies the distributed parameter circuit model for the frequency-dependent impedance of vertically driven ground rods by considering multi-layered soil structures where ground rods are buried. The Matlab program was used to calculate the frequency-dependent ground impedances for two ground rods of different lengths. As a result, an increase of the length of ground rod is not always followed by a decrease of grounding impedance, at least at a high frequency. The results obtained using the newly proposed simulation method considering multi-layered soil structures are in good agreement with the measured results.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2008년도 하계학술대회 논문집
• /
• pp.643-645
• /
• 2008

Stainless steel 304 and 316 plates were deposited with the multi-layered coatings of titanium film (0.1um) and gold film (1-2um) by an electron beam evaporation method. The XRD patterns of the stainless steel plates modified with the multi-layered coatings showed the crystalline phases of the external gold film and the stainless steel substrate. Surface microstructural morphologies of the stainless steel bipolar plates modified with multi-layered coatings were observed by AFM and FE-SEM images. The external gold films formed on the stainless steel plates showed microstructure of grains of about 100nm diameter. The grain size of the external surface of the stainless steel plates increased with the gold film thickness. The electrical resistance and water contact angle of the stainless steel bipolar plates covered with multi-layered coatings were examined with the thickness of the external gold film.

• 한국전기전자재료학회논문지
• /
• 제18권10호
• /
• pp.950-955
• /
• 2005

For the insulation design of a high temperature superconducting(HTS) cable, three kinds of design method were proposed, which used AC and impulse withstand voltage and partial discharge inception strength. However, the designed insulation thickness by AC and impulse could not be applied to cable fabrication process due to much low electrical breakdown strength. The effect of the multi-layered insulation paper was not considered on the previous insulation design and the insulation thickness by partial discharge inception strength could be applied only. In this paper, the electrical breakdown characteristic, which considered the effect of multi-layered of LPP, was investigated to design the insulation thickness.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.223-224
• /
• 2006

This paper present a new disk-type piezoelectric transformer. The input side of the transformer has a crescent-shaped electrode and the output side has a focused poling direction. This transformer has multi-layered structure. The piezoelectric transformers operated m each transformer's resonance vibration mode. The electrodes and poling directions on commercialy available piezoelectric ceramic disks were designed so that the planar or shear mode coupling factor ($k_p,\;k_{15}$) becomes effective rather than the transverse mode coupling factor ($k_{31}$). The Resonance frequency is 65.22[kHz] and maximum voltage step-up ratio is 149. Multi-layered transformer has better efficiency and step-up ratio than the single-layered transformer.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.665-672
• /
• 2000

The problems of discontinuous layer interface are very important in the algorithm and programming for the analysis of multi-layered consolidation using a numerical analysis, finite difference method(F.D,M.). Better results can be obtained by the process for discontinuous layer interface, since it can help consolidation analysis to model the actual ground Explicit method is simple for analysis algorithm and convenient for use except for applying the operator Crank-Nicolson method represents implicit method, which have different analysis method according to weighting factor. This method uses different algorithm according to dimension. And, this paper uses alternative direction implicit method. The purpose of this paper provides an efficient computer algorithm based on numerical analysis using finite difference method which account for multi-layered soils with confined aquifer to determine the degree of consolidation and excess pore pressures relative to time and positions more realistically.

• 한국공작기계학회논문집
• /
• 제16권5호
• /
• pp.183-190
• /
• 2007

It is well known that abrasive waterjet(AWJ) was developed as a kind of high-density energy processing technologies. AWJ is used to obtain the better cutting quality of various materials such as metals, ceramics, glass and composite materials within a short manufacturing time because of the characteristics of heatless and noncontact processing. However, AWJ device still has some problems to obtain the high quality of thin workpiece. In this paper, we investigated the optimal microcutting conditions of AWJ, such as maximum pressure, cutting speed and standoff distance of thin multi-layered materials. The experimental results show that AWJ has possibilities and potential to apply to the microcutting of thin multi-layered materials for IT industrial applications.

• 멤브레인
• /
• 제9권2호
• /
• pp.126-131
• /
• 1999

당뇨병 환자의 혈당치 측정을 위하여 다층젤라틴 필름으로 만들어진 진단막을 제조하였다. 플라즈마와 혈액 속의 글루코우즈의 농도 변화에 따른 최대확산속도를 측정하였다. 여러 가지 온도에서 3일, 2주, 4주 보관후 온도가 글루코우즈의 확산속도에 미치는 영향을 조사하였다. 다층 젤리탄 진단막의 안정성을 상대습도 80%에서 측정하였다.