• Corrosion Science and Technology
• /
• v.2 no.3
• /
• pp.141-147
• /
• 2003

Sputter-deposited Nb-Al-Cr alloys. $3-5{\mu}m$ thick, have been prepared on quartz substrates as oxidation-and sulfidation-resistant materials at high temperatures. The oxidation or the alloys in the $Ar-O_2$ atmosphere of an oxygen partial pressure of 20 kPa follows approximately the parabolic rate law, thus being diffusion controlled. Their oxidation rates are almost the same as or even lower than those ofthc typical chromia-forming alloys. The multi-lavered oxide scales are formed on the ternary alloys. The outermost layer is composed of $Cr_2O_3$, which is"mainly responsible for the high oxidation'resistance of these alloys. In contrast to sputter-deposited Cr-Nb binary alloys reported previously, the inner layer is not porous. TEM observation as well as EDX analysis indicates that the innermost layer is a mixture of $Al_2O_3$ and niobium oxide. The dispersion of $Al_2O_3$ in niobium oxide may be attributable to the prevention of the formation of the porous oxide layer. The sulfidation rates of the present ternary alloys arc higher than those of the sputter-deposited Nb-AI binary alloys, but still several orders of magnitude lower than those of conventional high temperature alloys. Two-layered sulfide scales are formed, consisting of an outer $Al_2S_3$ layer containing chromium and an inner layer composed of $NbS_2$ and a small amount of $Cr_2S_3$. The presence of $Cr_2S_3$ in the inner protective $NbS_2$ layer may be attributed to the increase in the sulfidation rates.

• Macromolecular Research
• /
• v.17 no.2
• /
• pp.91-98
• /
• 2009

Conjugated PPV-derived block copolymers containing 2-ethylhexyloxynaphthalene unit were synthesized and characterized in this study. The resulting polymers were soluble in common organic solvents and showed good thermal stabilities, The weight-average molecular weights ($M_w$) of the copolymers ranged from 246,000 to 475,000 with PDIs of $1.3{\sim}2.1$. The optical properties of these polymers, measured both in a chloroform solution and on a film, showed a maximum absorption at $405{\sim}476\;nm$ for Copolymers $I{\sim}VIII$. In the PL spectra, Copolymers $I{\sim}VIII$ showed maximum peaks at $510{\sim}566\;nm$. The HOMOs, LUMOs and band gaps of the PPV derivatives of Copolymers $I{\sim}VIII$ were $5.30{\sim}5.77$, $3.04{\sim}3.24$, and $2.5{\sim}2.2\;eV$, respectively, The multi-layered, light-emitting diodes of ITO/PEDOT/copolymers/LiF/Al exhibited turn-on voltages of $6{\sim}2.5\;V$ Copolymer VIII exhibited the maximum brightness of $3.657\;cd/m^2$. Particularly, Copolymer VII, with an identical composition of MEH-PPV and naphthalene-PPV, showed a maximum luminance efficiency and power efficiency of 2,63 cd/A and 1.06 lm/W, respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.1
• /
• pp.83-91
• /
• 2014

In this study, we synthesized two different silica monoliths by using sol-gel, solvent exchange, surface modification, ambient pressure drying processes, and surfactant-based templating technique followed by calcination process. All of the prepared two silica monoliths showed crack-free appearance with fairly good transparency, and furthermore were confirmed to have extremely high porosity, specific surface area, and mean pore size below 30 nm. The silica aerogel sample exhibited finer and more homogeneous nano-sized pore structure due to spring back effect caused by surface modification, which resulted in better thermal insulation performance. Based on measured thermal conductivities and theoretical relationship, multi-layered glass window system in which silica monolith prepared in this study was inserted as a middle layer was revealed to have superior thermal insulation performance compared to conventional air-inserted glass window system.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.1
• /
• pp.71-77
• /
• 2014

In this paper, we propose an improved numeric character recognition method which can recognize numeric characters well under low-illuminated and shade-illuminated environment. The LN(Local Normalization) preprocessing method is used in order to enhance low-illuminated and shade-illuminated image quality. The reading area is detected using line segment information extracted from the illumination-normalized meter images, and then the three-phase procedures are performed for segmentation of numeric characters in the reading area. Finally, an efficient hybrid classifier is used to classify the segmented numeric characters. The proposed numeric character classifier is a combination of multi-layered feedforward neural network and template matching module. Robust heuristic rules are applied to classify the numeric characters. Experiments using meter image database were conducted. Meter image database was made using various kinds of meters under low-illuminated and shade-illuminated environment. The experimental results indicates the superiority of the proposed numeric character recognition method.

• Journal of Digital Convergence
• /
• v.12 no.5
• /
• pp.395-401
• /
• 2014

As social network service becomes common, the consumers use many discount coupons with which they can purchase goods via social commerce. Although, the quantities of coupons offered from social commerce are currently on the sharp increase, customized coupon service that reflects user preference is not offered. This paper proposes a coupon service method reflecting user's subjective inclination targeting food coupons to offer customized coupon service for social commerce. Towards this end, this paper conducts hierarchization of the factors that become standard in selecting coupons including food types, food prices, discount rates and the number of buyers. And then, this study classifies, extracts and offers the coupons using Fuzzy-AHP, a decision making support method that reflects subjective inclination. From the user satisfaction results on the extracted coupons, the users are generally satisfied: very satisfactory with 45%, satisfactory with 33% and fair with 22%, and there was no experiment participant, who was dissatisfied.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.12
• /
• pp.1460-1466
• /
• 2010

In this paper, we analyzed the performance of radar target classification using the monostatic and bistatic radar cross section(RCS) for four different wire targets. Short time Fourier transform(STFT) and continuous wavelet transform (CWT) were used for feature extraction from the monostatic RCS and the bistatic RCS of each target, and a multi-layered perceptron(MLP) neural network was used as a classifier. Results show that CWT yields better performance than STFT for both the monostatic RCS and the bistatic RCS. And, when STFT was used, the performance of the bistatic RCS was slightly better than that of the monostatic RCS. However, when CWT was used, the performance of the monostatic RCS was slightly better than that of the bistatic RCS. Resultingly, it is proven that bistatic RCS is a good cadndidate for application to radar target classification in combination with a monostatic RCS.

• Ocean Systems Engineering
• /
• v.5 no.1
• /
• pp.1-19
• /
• 2015

The water jetting system for a jack-up spudcan requires the suitable design considering the platform/spudcan particulars, environments, and soil conditions, either the surficial clay or surficial sand. The usage of water jetting depends critically on soil conditions. The water jetting is usually used for the smooth and fast extraction of the spudcan in the surficial clay condition. It is also required for inserting spudcan up to the required depth in the surficial sand condition, which is investigated in this paper. Especially, it should be very careful to use the water jetting during an installation of spudcan in the surficial sand condition, because there is a risk of overturning accident related to the punch-through. Therefore, in this study, the effect of water jetting flow rate and time on the change of soil properties and penetration resistance is analyzed to better understand their interactions and correlations when inserting the spudcan with water jetting in surficial sand condition. For the investigation, a wind turbine installation jack-up rig (WTIJ) is selected as the target platform and the multi layered soil (surficial sand overlaying clays) is considered as the soil condition. The environmental loading and soil-structure interaction (SSI) analysis are performed by using CHARM3D and ANSYS. This kind of investigation and simulation is needed to decide the proper water jetting flow rate and time of spudcan for the given design condition.

• Smart Structures and Systems
• /
• v.26 no.3
• /
• pp.331-343
• /
• 2020

In this paper, based on the CPT, motion equations for a sandwich plate containing a core and two integrated face-sheets have derived. The structure rests on the Visco-Pasternak foundation, which includes normal and shear modules. The piezo-magnetic core is made of CoFe₂O₄ and also is subjected to 3D magnetic potential. Two face sheets at top and bottom of the core are under electrical fields. Also, in order to obtain more accuracy, the effect of flexoelectricity has took into account at face sheets' relations in this work. Flexoelectricity is a property of all insulators whereby they polarize when subject to an inhomogeneous deformation. This property plays a crucial role in small-scale rather than macro scale. Employing CPT, Hamilton's principle, flexoelectricity considerations, the governing equations are derived and then solved analytically. By present work a detailed numerical study is obtained based on Piezoelectricity, Flexoelectricity and modified couple stress theories to indicate the significant effect of length scale parameter, shear correction factor, aspect and thickness ratios and boundary conditions on natural frequency of sandwich plates. Also, the figures show that there is an excellent agreement between present study and previous researches. These finding can be used for automotive industries, aircrafts, marine vessels and building industries.

• Journal of the Korean Magnetics Society
• /
• v.18 no.1
• /
• pp.43-47
• /
• 2008

[ $ZnO-Bi_2O_3-Al_2O_3-B_2O_3-SiO_2$ ] nano-glass has been prepared by sol-gel method. The mean particle size was 60.3 nm with narrow size distribution. The nano-galss has been used as a sintering aid for the densification of the NiZnCu ferrites. The ferrite was sintered with nano-glass sintering aids at $840{\sim}900^{\circ}C$, 2 h and the initial permeability, quality factor, density, and saturation magnetization were also measured. The initial permeability of 0.5 wt% nano-glass added toroidal sample for NiZnCu ferrites sintered at $900^{\circ}C$ was 193.3 at 1 MHz. The initial permeability and saturation magnetization were increased with increasing annealing temperature. As a result, $ZnO-Bi_2O_3-Al_2O_3-B_2O_3-SiO_2$ nano-glass systems were found to be useful as sintering aids for multilayer chip inductors.

• Lingua Humanitatis
• /
• v.1 no.2
• /
• pp.141-158
• /
• 2001

Criticism of today finds itself in an awkward situation, for it is now being transformed in the same way that literature and the arts were transformed by the avant-garde movements at the end of the 19th century and the beginning of the 20th century. It is characterized predominantly by a break with harmony and with the values of realism. As such, it is driven by a post-modem ethos, an artistic, social, and cultural phenomenon that veers toward open, fragmentary, and indeterminate forms. In this paper, I examine today's most urgent social and cultural issues with reference to artistic production and criticism, in order to illuminate the true nature of criticism. The outstanding questions in the world of art criticism are given in five categories: the lack of critical reality in argumentative criticism; the problem of artistic and literary production in global capitalism; the artistic mind and its consciousness of socio-historical ideology; anxiety of the rise of cyberjournalistic criticism; and the question of subordination to western systems in the field of interpretation and criticism. For my analysis, I have tried to formulate a three-dimensional critique structure that will help us organize the relationships between the points of argument: 1) criticism as a creative force behind the artist; 2) criticism as critique of artistic production; and 3) criticism as critique of other critics. This multi-layered structure will be appropriate to our task of interpretation and evaluation, as the proposed complex structure of criticism will be able to embrace the diverse aspects of our problematic argument. In the final analysis, my argument resolves itself into a question of art, more specifically into a question of criticism as a protective device of art in an age threatened by globalization and cultural monopolization.