• Journal of the Korean Society for Marine Environment & Energy
• /
• v.13 no.2
• /
• pp.83-90
• /
• 2010

The hydrodynamic interaction of two floating bodies in waves freely floating or connected by a rigid link is studied by using a boundary element method in the frequency-domain. The exact two-body hydrodynamic coefficients of added mass, wave damping and exciting force are calculated from the radiation-diffraction potential solution of the improved Green integral equation associated with the free surface Green function. The irregular frequencies in the conventional Green integral equation make it difficult to predict the physical resonance of the fluid in the gap between two bodies floating side by side. However, the improved Green integral equation employed in this study is free of irregular frequencies and always yields the exact solution of the multi-body radiation-diffraction potential boundary value problem. The 6 degree-of-freedom motions of two bodies freely floating side by side or connected parallel by a rigid link have been calculated for the incident wave frequencies ranging from 0.1 to 5 radians per second in head, left and right bow quartering seas. The 6-component load of the rigid link have also been presented.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.2
• /
• pp.105-111
• /
• 2009

The powers used in the motor drive system are mostly DC sources like batteries. Even AC powers in some systems are generated from DC sources by the inverter. It is can be forecasted that the DC-link communications will be widely used in various industrial fields. In this paper a novel BLDC motor drive system using DC-link communications is proposed. The characteristic of this system Is that the communication only needs 2 DC lines. There are not additional lines to translate the reference signals. And the reliability o3 the system is ensured especially under some terrible circumstances. The number of lines can be minimized when the DC-link communication method is applied in the multi motor control system and the slip ring design also can be simplified when this method is applied in rotation machines. The proposed motor system is clarified by the PSIM and MATLAB simulations and tested through the hardware prototype.

• Journal of KIISE:Information Networking
• /
• v.32 no.2
• /
• pp.215-219
• /
• 2005

Generally, the mobile nodes in MANET have the limited power capacity available for actual communications. Thus, the power management is very important for packet routing or forwarding. Although MTPR, MBCR and MMBCR are proposed to treat the problem of power consumption, there have been few researches resolving the link breakdown that is occurred by the power exhaustion during transmission. In this sense, the reliable scheme should be required to ensure the routing connectivity. In this paper, we propose three schemes to enforce the routing connectivity. If the signal strength is dropped below a signal threshold, the candidate route is previously selected to prepare the link breakdown. Also, on multi-channel, we propose the lifetime increment scheme of a node that it manage its available power to the needed power of a new link. The simulation results show the enforcement of the link connectivity and the performance improvements of the delay time through the effective connection management.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.1
• /
• pp.3-8
• /
• 2006

This paper deals with an automated computer-aided process planning and die design system by which designer can determine operation sequences even if they have a little experience in process planning and die design for axisymmetric products. An attempt is made to link programs incorporating a number of expert design rules with the process variables obtained by commercial FEM softwares, DEFORM and ANSYS, to form a useful package. The system can provide a flexible process based on either the reduction in the number of forming sequences by combining the possible two processes in sequence, or the reduction of deviation of the distribution on the level of the required forming loads by controlling the forming ratios. Especially in die design module optimal design technique and horizontal split of die insert were investigated for determining appropriate dimensions of components of multi-former die set. Results obtained, using the modules, enable the design and manufacture of a die set for a multi-former to be more efficiently performed.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.8-17
• /
• 2015

This paper analyses the power flow of a three-feeder/multi-bus distribution system by a custom Generalized Power Quality Conditioner (GUPQC). The GUPQC has been realized by three voltage source converters (VSCs) coupled back-to-back through a common DC-link capacitor on the DC-side. One feeder was controlled by the shunt compensator, whereas each of the other two feeders was controlled by the proposed novel series compensator. The GUPQC has the capability to simultaneously compensate voltage and current quality problems of a multi-bus/three-feeder distribution system. Besides that, the power can be transferred from one feeder to other feeders to compensate for poor power quality problems. Extensive simulation studies were carried out by using MATLAB/SIMULINK software to establish the ability of the GUPQC to improve power quality of the distribution systems under distorted supply voltage conditions.

• Proceedings of the IEEK Conference
• /
• 2004.06a
• /
• pp.301-304
• /
• 2004

In this paper, we propose a method to find the optimal direction of the multi beam between each station on the point-to-point link by genetic algorithm. In the proposed method, maximum value in optimal direction on each station is used as a fitness function. The beam of millimeter wave generates a lot of multi-peak because of much influence of noise. About each gene, we simulated this method using 16bit, 32bit, and 32bit split algorithm. 32bit split uses 16bit gene information. Each antenna makes 32bit gene information by adding gene information of two antennas having 16bit gene. Through the proposed method, we could have gotten a good output without 32bit gene information.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.279-282
• /
• 2007

Typically a wireless sensor network consists of a number of nodes that sense surrounding environment and collaboratively work to process and route the sensing data to a sink or gateway node. We propose an architecture with support of multiple routers in IPv6-based Low-power Wireless Personal Area Network (6LoWPAN). Our architecture provides traffic load balancing and increases network lifetime as well as self-healing mechanism so that in case of a router failure the network still can remain operational. Each router sends its own Router Advertisement message to nodes and all the nodes receiving the messages can select which router is the best router with the minimum hop-count and link information. We have implemented the architecture and assert our architecture helps in traffic load balancing and reducing data transmission delay for 6LoWPAN.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.11B
• /
• pp.1540-1545
• /
• 2001

This paper is concerned with the reverse link performance of multi-code CDMA systems in multipath fading environments. The degree of orthogonality loss among multiple spreading code channels is characterized as the orthogonality factor. It depends on various system parameters including multipath power profiles of propagation channels and the number of Paths resolved at a Rake receiver. The effect of the parameters on the system performance is then investigated in terms of bit error rate and required signal quality. The results show that multipath delay power profiles dominantly affect mutual interference among multi-code channels and multipath combining gain by bandwidth expansion is not so great due to the increase of the mutual interference. Moreover, the orthogonality factor is derived as the value of between (1/m) and 1.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.5
• /
• pp.439-444
• /
• 2012

In this study, we address the formation control problem of coupled unicycle-type mobile robots, each of which can interact with its neighboring robots by communicating their position outputs. Each communication link between two mobile robots is assumed to be established according to the given time-varying interconnection topology that switches within a finite set of connected fixed undirected networks and has a non-vanishing dwell time. Under this setup, we propose a distributed formation control algorithm by using the dynamics extension and feedback linearization methods, and by employing a consensus algorithm for linear multi-agent systems which provides arbitrary fast convergence rate to the agreement of the multi-agent system. Finally, the proposed result is demonstrated through a computer simulation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.4
• /
• pp.865-872
• /
• 1998

This paper proposes a multiuse detection system in a multi-cell M-ary Frequency Shift Keying(MFSK)/frequency hopping(FH)-Code Division Multiple Access(CDMA) environment, in which the channel model is an OR-channel and in the reverse link. We have proposed a multiuse detection system in a single cell. However, this sitye is not adequate to detect multiuser in a multi-cell environment. Therefore, we propose a multiuser detection system based on 3 level OR decision with two threholds. The proposed detection system can delete interference as well as intra-cell interference, receive the weakened desired signal and reject the false alarm. computer simulation shows the performance improvement.