• 한국전산유체공학회:학술대회논문집
• /
• 2004.10a
• /
• pp.19-24
• /
• 2004

A great deal of exhaust gas inside a combustion room goes out through exhaust pipe but residual gas, is called 'Blow by gas', enters the crankcase through a small gap between the piston and the cylinder wall. Here, if the crankcase isn't vented, this causes many bad effects such as lubricant oil contamination, corrosion by that and crankcase explosion by rising pressure. So most automobiles are constituted with a PCV(Positive Crankcase Ventilation) system to prevent previous problems. PCV valve is the most important part in this ventilation system. When companies are manufacturing new cases, engineers are designing it depending on their experiments than theoretical knowledges. Much efforts and times are needed for new development. This study will show quantitative results to increase the possibilities.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.3
• /
• pp.342-348
• /
• 2012

This paper presents a moving-magnet type linear actuator designed by using flux concentration type permanent magnet arrangement, which can generate higher magnetic flux density in air-gap. In this construction, detent force which is induced by both slot-effect and end-effect becomes larger due to strong attractive forces. To reduce cogging force we have employed a modular mover structure of two magnetic pole sections connected with a center yoke. The improved motor performance is demonstrated with the prototype machine.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.5
• /
• pp.547-553
• /
• 2004

A hemispherical asperity moving over a flat plane is simulated based on classical molecular dynamics. The asperity and the plane consist of silicon atoms whose interactions are governed by the Tersoff three-body potential. The gap between the asperity and the plane is maintained to produce attractive normal force in order to investigate the adhesive friction and wear. The simulation focuses on the influence of crystallographic orientation of the contacting surfaces and the moving direction. It is demonstrated that the adhesive friction and wear are lower when crystallographic orientations of the contacting surfaces are different, and also depend on the moving direction relative to the crystal1ographic orientation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.780-785
• /
• 2001

A moving-magnet type pickup actuator is proposed, which has the back-yoke to improve th sensitivity. Through the magnetic path analysis, we can find that the flux density is increased i the air gap by the pole assignment of magnet and the adding of back-yoke can reduce the flu leakage and induce 40％ up of flux density. Experimental results show that the sensitivity i improved in the tracking direction, however, the improvement doesn't occur in the focusing direction. Finally, the compensation performance is tested in HD-DVD system. And it is verifie that the actuator can compensate the disc tilt of ${\pm}$0.7$^{\circ}$.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.9
• /
• pp.138-148
• /
• 1996

In moving structures such as robots and feeders of production lines, vibrations may not be ignored. Recently it becomes a big problem to control the vibration in a motion because moving structures are in higher speed, larger size and lighter weight. In this study a nonlinear system was model- led and identified by using neural networks and the vibration in motions was controlled actively by using a neural network controller. To investigate vilidity of this method, an experimental apparatus was made and tested. The model was composed of a DC servomotor, a carrier and a flexible plate. Its motion was measured by a gap sensor and an encoder. Trapezoidal, cycloid and trapecloid type trajectories were used in this exper- riment. Computer simulations and experiments weredone for each trajectory.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.2
• /
• pp.53-59
• /
• 2002

This paper shows the experimental results controlling the height of surface and back bead in GMAW by analyzing the unexpected gaps between base metals produced in welding and by controlling welding velocity due to the variation of the gap between base metals in thin-plate welding. The back bead behavior and burn-through in I-type butt joint $CO_2$ welding of thin mild steel are analyzed in the views of short circuit time ratio and short circuit frequency. It is shown through experimental consideration that the short circuit time ratio method is more reasonable than the short circuit frequency method in analyzing the formulation of back bead under changing the gap between base metals. Based on the these results, welding manipulator is designed so as to satisfy the bead height control in real time by measuring the short circuit time ratio. To show the effectiveness of the developed bead formulation control system, the experiment is implemented under two welding conditions such as increasing gap from 0mm to 0.8mm and gradually increasing gap from 0mm to 1.2mm. The experimental results show that the bead formulation can be controlled uniformly in spite of the variation of the gap between base metals.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.8
• /
• pp.76-85
• /
• 2003

In this paper, a technical method for removing the solder from PCBs has been proposed to simplify the pulverizing process and to get higher quality of materials for recycling of the electronic parts in the Printed Circuit Boards (PCBs). There are several techniques to remove the solder from PCB, such as physical and chemical method, vibration, suction and blowing and so on. Among them, the suction technique turned out the best method by investigation. In the suction method, there are three variables for removing the solder. They are a temperature of the thermal wire, a velocity of moving PCB and a gap between PCB and thermal wire. To find the optimal variables for the system, an experiment has been conducted by a trial and error method. The optimal variables were found $220^{\circ}C$ of temperature, 11.58mm/s of velocity, 10mm of gap (A gap between suction hole and bottom of PCBs is 5mm). The result of the experiment shows that 50% of the solder were removed.

• Journal of Welding and Joining
• /
• v.19 no.3
• /
• pp.267-273
• /
• 2001

In this study, welding phenomena involved in formation of penetrators during high frequency electric resistance welding were investigated. High speed cinematography of the process revealer that a molten bridge between neighboring skelp edges forms at apex point and travels along narrow gap toward to welding point at a speed ranging from 100 to 400 m/min. The bridge while moving along the narrow gap swept away oxide containing molten metal from the gap, providing oxide-free surface for a forge-welding at upsetting stand frequency of the budge formation, travel distance and speed of the bridge were affected by the heat input rate into strip. The travel distance and its standard deviation were found to have a strong relationship with the weld defect density. Based on the observation, a new mechanism of the penetrator formation during HF ERW process is proposed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.05a
• /
• pp.140-143
• /
• 1992

This paper deals with the dielectric behaviors of $SF_{6}$ gas and prebreakdown growth caused by lightning impulse voltages in inhomogeneous field perturbed with a fixed needle-shaped protrusion on the electrode. The measuring interpretation of the external current induced by moving charges is described. The temporal growth of prebreakdown is obserbed by using a shunt and photomultiplier. The prebreakdown processes are initiated by the first streamer corona at a needle protrustion, the flashover of the main gap in the positive polarity is very sensitive to the local field and propagates into the gap with the leader mechanism. It is found that the dependence of the prebreakdown phenomena on the polarity of applied voltages is caused by the effect of space charges. In addition, the proposed measuring techniques are very useful to perform the measurements of avalanche currents, corona discharges in inhomogeneous fields ad partial discharges in voids.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1438-1440
• /
• 1998

In this work, simultaneous measur of space charge and conduction current was c out in LDPE with air gap by Pulsed-Electro-Aco Method. Also, effect of long time charging at con electric field on the formation of space charge conduction was investigated. From the experim results. we knew that the homo space charge formed near the dielectric surfaces and moving the bulk of dielectric as the electric field elevated. This was related with the deep traps b carriers and de trapping by Poole-field lowering conduction current was coincident with the Pool emission. From the long time charging experimen obtained the results that the negative space was moving into the dielectric bulk as the cha continued and the positive space charge accumulated at upper surface of LDPE.