• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.564-568
• /
• 2006

Smooth picture module is operated by vibration to tilt the light from the DMD (digital micro mirror device) of DLP projection TV, which makes the screen of the TV smoother and DMD chip cost lower. To satisfy the vibration characteristics of smooth picture module, it is designed by optimizing moment of inertia, spring constant and damping coefficient, using structural and fluid dynamic simulation that showed a good agreement with experimental data. To reduce the material cost and moment of inertia, engineering plastic is used and the reliability is estimated. A VCM (voice coil motor) type actuator for smooth picture has to satisfy performance requirements such as higher driving force, lower power consumption, and lower cost. The initial design and optimization for VCM was performed using FE analysis. It allowed us to optimize the design of magnetic circuit of the proposed actuator to obtain higher force while maintaining a lower cost.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2526-2528
• /
• 1999

Parameters of equivalent circuit of IPMSM are varied according to current magnitude and current phase angle. Especially, Parameter variation of IPMSM for an electric vehicle(EV) is critical. Because current magnitude is very large. and current phase angle range also is wide. So, variation characteristics of $L_d$ and $L_q$ of the IPMSM are analyzed and verified through experiments. And then new parameter estimator of $L_d$ and $L_q$ that is constructed by neural network technique is suggested Using numerical method, the advanced characteristics of current controller of vector control algorithm is verified.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1291-1293
• /
• 1998

Power MOSFETs are very important Devices in power circuit applications such as motor control, switch mode power supplies & telecommunicatioelectronics. In order to investigated the Avalanch Energy value of MOSFET due to Misalign. Some samples made under several different $P^+$ misalign and $N^+$ misalign. The relationship between evalanch energy value and misalign is investigated as well in this paper.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.85-87
• /
• 1993

SRM drive system is suitable for high performance drive over a wide speed range because of its outstanding instantaneous torque characteristics, controllability and simple drive structure. The realization of high efficiency SRM system is archived by design of optimal magnetic structure, and by development of switching drive circuit. So, this study describes the design standard of the winding number of stator pole for optimal magnetic structure.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.962-967
• /
• 1991

A counter balance valve is used as one part of hydraulic motor brake system. The function of this valve is to protect over-run or free falling of inertia load. But occasionally the brake system with counter balance valve makes some undesirable problems such as pressure surges or vibrations. In this study, for the purpose of easy estimation about dynamic characteristics of hydraulic system including counter balance valve, precise formulation describing fluid dynamics and valve dynamics under various boundary conditions were made. Dynamic characteristics were analysed by numerical integration using Runge-Kutta method, because the equations in this circuit with counter balance valve contain various nonlinear terms. Propriety of this analysis method is verified by experiment. For the purpose of obtaining fundamental data for preventing instability, this study experimented the effects of the spool taper, spring constant, cylindrical choke. And we developed double acting brake system integrated counter balance valve.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10b
• /
• pp.896-901
• /
• 1990

A simulation analysis is presented for the position control of a single-link flexible manipulator whose end-effector is subjected to an impulsive force. Arm is rotated by a d.c. servomotor at the shoulder so that the end point stays precisely at its initial position even if the end effector is thumped with the impulsive loading. A gap sensor is used to measure the tip displacement. The control torque based on the PD control law is applied to the motor through the driver circuit. The control strategy is tested by means of computer simulation for the one-link flexible-arm prototype in the authers' laboratory at Tohoku Univ.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.291-298
• /
• 2005

This paper describes the characteristic feather of propulsion system adopting mass production. The train formation is composed of 4 cars by 2 Motor cars and 2 Train cars. Acceleration rate must be 3.0 km/h/s or more when the car starts up to 35km/h by 16ton of passenger load. The system information supervision is easy because the system is controlled to perfect digital circuits, all information of an action is stored in a memory and is managed. The control system is composed of a fully digital circuit and a high level software such as C language. The DSP TMS320C31 is used for main processor and has the capability of 50MHz, 32bit floating point operation and has a C compiler. Therefore, the implementation of control algorithm and the change of function are easy. VVVF inverter using IGBT conducted variable combined test, environment test using chamber, interface test and field test etc.

• Journal of Industrial Technology
• /
• v.19
• /
• pp.1-7
• /
• 1999

This is the pre-study to pile up the basic technique for the electro-discharge machining in the field of micro-drilling. The machined chips are flowed out from the machining area by the flow arisen from the high speed rotation of the electrode. The cylindrical shape electrode, whose diameter is 0.5mm, is clamped by the three point clamping type clamper and the clamper is attached at the front shaft of the high speed rotating DC motor. The current for machining is controlled by pulse width modulation technique and the machining conditions such as frequency and duty ratio are changed to find out the effect of the variables for machined results.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.80-82
• /
• 2004

The single phase switched reluctance motor(SRM) is more simpler and robust in the structure than poly phase SRM. It has the merits that it reduces the switching elements and the energy density per volume is very high. Recently, it has been researched and developed in various types and starting method due to the technique of power electronics and the computer added design. This paper presents a analytical representation of the phase inductance of a single phase SRM, as function of position and current, taking into account the non-linearity of the magnetic circuit. the method is based on Fourier series expansion. Analytical expressions for the calculation of instantaneous phase inductance, flux linkage, coenergy and electromagnetic torque as a function of rotor position and winding currents are derived.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.65 no.2
• /
• pp.84-87
• /
• 2016

This paper deals with Energy Harvesting using a part of physical energy which is generated by pulldown actions. From a point of energy harvesting view, though it is difficult to regenerate constant energy during pulldown exercise unlike cyclic exercise and running machine exercise, it is possible to regenerate some energies to charge batteries for mobile phones. To investigate possibility of energy harvesting during pulldown exercise, a voltage regulation experiment was performed with a converter circuit and a motor which is attached to the exercise equipment. And we conclude that energy harvesting is possible although its small quantity during pulldown exercises.