• 전력전자학회논문지
• /
• 제3권3호
• /
• pp.206-213
• /
• 1998

본 논문에서는 유도전동기의 속응 토크제어를 위한 파라미터 변동의 적응보상기법을 제안하였다. 제어성능을 현저히 저하시키는 원인으로 작용하는 파라미터의 변동을 보상하기 위하여 본 논문에서는 모델기준 적응제어(MRAC)방식을 적용하여 회전자 저항값 변동을 추정 보상한다. 본 적응제어방식은 실측 순시무효전력과 추정 순시무효전력의 오차관계에서 실시간으로 회전자 저항값 변동을 추정 보상하는 방식이다. 본 방식은 전동기 파라미터를 사용하지 않고 실측 순시무효전력을 기준모델로 적용하기 때문에 전동기 등 등가모델에서 구한 기존의 다른 기준모델에 비해 강인한 시스템이 된다. 추정된 회전자 저항값을 이용하여 자속관측기를 구성하고 이를 직접베터 제어방식에 적용하였으며, 시뮬레이션 및 실험을 통하여 속응 토크제어가 원활히 수행됨을 입증하였다.

• Journal of Power Electronics
• /
• 제6권3호
• /
• pp.235-244
• /
• 2006

Recently, speed sensorless vector control for synchronous reluctance motors (SYRMs) has deserved attention because of its advantages. Although rotor angle calculation using flux estimation is a straightforward approach, the DC offset can cause an increasing pure integrator error in this estimator. In addition, this method is affected by parameter fluctuation. In this paper, to control the motor at the low speed region, a modified programmable cascaded low pass filter (MPCPLF) with sensorless online parameter identification based on a block pulse function is proposed. The use of the MPCLPF is suggested because in programmable, cascade low pass filters (PCLPF), which previously have been applied to induction motors, the drift increases vastly wl)en motor speed decreases. Parameter identification is also used because it does not depend on estimation accuracy and can solve parameter fluctuation effects. Thus, sensorless speed control in the low speed region is possible. The experimental system includes a PC-based control with real time Linux and an ALTERA Complex Programmable Logic Device (CPLD), to acquire data from sensors and to send commands to the system. The experimental results show the proposed method performs well, speed and angle estimation are correct. Also, parameter identification and sensorless vector control are achieved at low speed, as well as, as at high speed.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제2권2호
• /
• pp.184-189
• /
• 2013

This paper proposes a method for improving the performance of a position sensorless control system for a slotless surface permanent magnet synchronous motor (SPMSM) in a very low-speed region. In position sensorless control based on a motor model, accurate motor parameters are required because parameter errors would affect position estimation accuracy. Therefore, online parameter identification is applied in the proposed system. The error between the reference voltage and the voltage applied to the motor is also affect position estimation accuracy and stability, thus it is compensated to ensure accuracy and stability of the sensorless control system. In this study, two voltage error compensation methods are used, and the effects of the compensation methods are discussed. The performance of the proposed sensorless control method is evaluated by experimental results.

• 조명전기설비학회논문지
• /
• 제16권5호
• /
• pp.45-52
• /
• 2002

본 논문에서는 데이터 수집 보드로부터 호스트 컴퓨터로 시리얼 통신 채널을 통하여 전송된 BLDC(Brushless DC)모터의 입력과 출력 정보를 이용하여 모터의 저항값을 추정함으로써 고장을 검출하는 고장검출 시스템을 제안하였다. 프레임 크기가 고정된 프로토콜을 설계하고, 주기적으로 통신이 이루어지도록 하여 시리얼 통신 채널에서 발생되는 대역폭 제한으로 인한 시간지연문제를 해결하였으며, 저항값을 추정하기 위하여 간략화된 BLDC모터 모델과 순환형 최소자승법 알고리즘을 사용하였다. 제안된 고장 검출 방법은 실험을 통하여 성능을 확인하였다.

• 전기학회논문지P
• /
• 제61권4호
• /
• pp.199-205
• /
• 2012

This paper propose a improved parameter estimations of five-phase squirrel-cage induction motor(IM) for speed control system on field oriented control(FOC). In order to high performance control of ac the motors using a FOC and DTC(direct torque control) algorithm, there are required precise motor parameters for slip calculation, flux observer, controller gain, rotor position and speed estimation, and so on. We are suggest a estimation method of the motor parameters that developing five-phase squirrel-cage IM have a stator of concentrated winding for experimental. There are results of stator winding test, no-load test, locked rotor test, and obtained equivalent circuits using manufactured experimental apparatus. For presenting the superior performance of the speed control system in adapted the parameters, experimental results are presented using a 32-bit fixed point TMS320F2812 DSP with 1.5[KW] IM.

• International Journal of Control, Automation, and Systems
• /
• 제1권3호
• /
• pp.308-314
• /
• 2003

This paper presents a serial communication based fault diagnosis scheme for a brushless DC (BLDC) motor using parameter estimation and Bayes classifier. The presented scheme consists of a smart network board, and a fault detection and isolation (FDI) master. The smart network board is installed near the BLDC motor drive system to acquire motor data and transmit motor data to the FDI-master via serial communication channel. The FDI-master estimates BLDC motor resistance to detect symptom of faults, and assign symptom to fault type using Bayes classifier. In this scheme, since communication time delay has a serious effect on performance, periodic and fixed communication protocol is designed. Hence, the delay time is priory known. By experiment result, presented scheme was verified.

• 전력전자학회논문지
• /
• 제24권2호
• /
• pp.92-98
• /
• 2019

Accurate estimation of motor parameters is required in some motor control applications. For example, the value of stator resistance is required for stator flux-oriented control mostly used in doubly fed induction generator systems. Stator resistance is not a constant value and continuously changes due to the rise in temperature during motor operation. Estimation errors degrade the control performance. Hence, this study proposes a simple stator resistance estimation method. In this scheme, the differential components of voltage and current values are used to eliminate the dead-time effect, and Kalman filter algorithm is applied to reduce the error according to measurement noise. Simulation and experimental results obtained with a permanent magnet motor show the validity of the proposed algorithm.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 B
• /
• pp.549-551
• /
• 1999

Recently, Several type of motors are used more widely in Fan system because of their low cost and high reliability. Therefore, the importance of fault detection and isolation of fan system significantly increases. The motor is a important factor bring out the fan system fault. So the problem of a fault detection for motor based on a parameter identification will be considered in this paper. After an introduction into fault detection with parameter estimation, a mathematical model for motor with special emphasis on motor itself. In the fault detection system, current and motor speed are used as parameter. Finally, simulation results are used to demonstrate the efficiency of the fault detection system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.19-20
• /
• 2012

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 A
• /
• pp.58-60
• /
• 1999

This paper presents dynamic performance prediction using Matlab / simulink after parameter estimation of synchronous reluctance motor considering iron loss. Test motor is 3 phase SynRM with the segmental rotor, rating power is 0.175KW. Experiment equipment is consists of testing motor, dynamometer, vector invertor dynamocontroller, and power analyser. The stator iron loss and rotor iron loss are modelled by additional windings on three-phase winding axis. These windings are transformed into d-q axis, and are represented as equivalent eddy current windings. P-Q circle diagram method and single phase standstill method are used to measure motor parameters considering iron loss.