• Advances in aircraft and spacecraft science
• /
• v.1 no.3
• /
• pp.291-310
• /
• 2014

An advanced model for the linear flutter analysis is introduced in this paper. Higher-order beam structural models are developed by using the Carrera Unified Formulation, which allows for the straightforward implementation of arbitrarily rich displacement fields without the need of a-priori kinematic assumptions. The strong form of the principle of virtual displacements is used to obtain the equations of motion and the natural boundary conditions for beams in free vibration. An exact dynamic stiffness matrix is then developed by relating the amplitudes of harmonically varying loads to those of the responses. The resulting dynamic stiffness matrix is used with particular reference to the Wittrick-Williams algorithm to carry out free vibration analyses. According to the doublet lattice method, the natural mode shapes are subsequently used as generalized motions for the generation of the unsteady aerodynamic generalized forces. Finally, the g-method is used to conduct flutter analyses of both isotropic and laminated composite lifting surfaces. The obtained results perfectly match those from 1D and 2D finite elements and those from experimental analyses. It can be stated that refined beam models are compulsory to deal with the flutter analysis of wing models whereas classical and lower-order models (up to the second-order) are not able to detect those flutter conditions that are characterized by bending-torsion couplings.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.7
• /
• pp.892-897
• /
• 2018

Due to population aging, an increase in the number of patients with chronic illnesses, and an increase in the number of single-person households, monitoring of health status in everyday life without the need for a hospital has become very important. For this reason, researches on various health care devices have been attempted, among which wearable devices are attracting much attention. In this paper, we propose a new ring-type wearable device for next generation healthcare. On the inner side of the ring, a metal electrodes for GSR measurement and an optical sensor for measurement of pulse wave signals of two wavelengths of red and near-infrared light were mounted. In addition, it was equipped with an acceleration sensor, and information about the degree of motion could be obtained. In this paper, it is shown that a health monitoring device can be implemented in the form of a ring, and the measured signals can be used to calculate heart rate, oxygen saturation, sleep time and sleep efficiency. Through the advanced algorithm, it is expected that we can extract various health information, especially sleep related health information by using the ring device, and it is also expected that it can contribute to the implementation of wearable healthcare effectively.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.8
• /
• pp.50-57
• /
• 2003

Controlling rotorcraft to fly precisely through multiple, irregularly, and closely spaced waypoints is a common and practical mission. However, finding an optimal trajectory for this kind of mission is quite challenging. Usability of traditional approaches such as inverse control or direct methods to this kind of problem is limited because of either limitation on the specification of the constraints or requirement of extensive computation time. This paper proposes a method that can easily compute the full trajectory and control history for rotorcraft to pass through waypoints while satisfying other general constraints of states such as velocities and attitudes on each waypoint. The proposed method is applied to rotorcraft guidance problems of slalom and linear trajectory in the middle of general curved trajectory. The algorithm is test for various situations and demonstrates its usability.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.11
• /
• pp.1332-1340
• /
• 2009

The front end wheel loader is widely used for the loading of materials in mining and construction fields. It has repetitive digging, loading and dumping procedures. The bucket is subjected to large resistance force from the soil during scooping. We considered the soil reaction force characteristics from scooping procedure, the protection by overload and automatic scooping mode algorithm. The main topic of this paper is the analysis of the soil reaction force characteristics. The analysis of soil mechanics is carried out and the developed soil model is verified by experimental results from the simplified experimental equipment. A simplified model of the soil shape and bucket trajectory is used to determine the scooping direction based on an estimation of the resistance force applied on the bucket during the scooping motion. In the future, this model will be used for the generation of an appropriate path for the wheel loader automation.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.5
• /
• pp.242-248
• /
• 2002

It is important to develop new effective technologies to increase the interruption capacity and to reduce the size of a UB(Gas Circuit Breakers). Major design parameters such as nozzle geometries and interrupting chamber dimensions affect the cooling of the arc and the breaking performance. But it is not easy to test real GCB model in practice as in theory. Therefore, a simulation tool based on a computational fluid dynamics(CFD) algorithm has been developed to facilitate an optimization of the interrupter. Special attention has been paid to the supersonic flow phenomena between contacts and the observation of hat-gas flow for estimating the breaking performance. However, there are many difficult problems in calculating the flow characteristics in a GCB such as shock wave and complex geometries, which may be either static or in relative motion. Although a number of mesh generation techniques are now available, the generation of meshes around complicated, multi-component geometries like a GCB is still a tedious and difficult task for the computational fluid dynamics. This paper presents the CFD program using CFB-CAD integration technique based on Cartesian cut-cell method, which could reduce researcher's efforts to generate the mesh and achieve the accurate representation of the geometry designed by a CAD tools.

• Korean Journal of Agricultural Science
• /
• v.42 no.1
• /
• pp.63-71
• /
• 2015

Path planning is an essential part for traveling and mowing of autonomous lawn mower tractors. Objectives of the paper were to analyze operation patterns by a skilled farmer, to extract and optimize waypoints, and to demonstrate generation of formatted planned path for autonomous lawn mower tractors. A 27-HP mower tractor was operated by a skilled farmer on grass fields. To measure tractor travel and operation characteristics, an RTK-GPS antenna with a 6-cm RMS error, an inertia motion sensing unit, a gyro compass, a wheel angle sensor, and a mower on/off sensor were mounted on the mower tractor, and all the data were collected at a 10-Hz rate. All the sensor data were transferred through a software program to show the status immediately on the notebook. Planned path was generated using the program parameter settings, mileage and time calculations, and the travel path was plotted using developed software. Based on the human operation patterns, path planning algorithm was suggested for autonomous mower tractor. Finally path generation was demonstrated in a formatted file and graphic display. After optimizing the path planning, a decrease in distance about 13% and saving of the working time about 30% was achieved. Field test data showed some overlap, especially in the turning areas. Results of the study would be useful to implement an autonomous mower tractor, but further research needs to improve the performance.

• The Journal of Korean Institute of Next Generation Computing
• /
• v.13 no.5
• /
• pp.39-50
• /
• 2017

Moving object tracking techniques can be considered as one of the most essential technique in the video understanding of which the importance is much more emphasized recently. However, irregularity of light condition in the video, variations in shape and size of object, camera motion, and occlusion make it difficult to tracking moving object in the video. Swarm based methods are developed to improve the performance of Kalman filter and particle filter which are known as the most representative conventional methods, but these methods also need to consider dynamic property of moving object. This paper proposes adaptive parameter control method which can dynamically change weight value among parameters in particle swarm optimization. The proposed method classifies each particle to 3 groups, and assigns different weight values to improve object tracking performance. Experimental results show that our scheme shows considerable improvement of performance in tracking objects which have nonlinear movements such as occlusion or unexpected movement.

• 전자공학회논문지 IE
• /
• v.43 no.4
• /
• pp.28-36
• /
• 2006

In this paper, an algorithm to classify the 4 motions of arm and a control system to position control the prosthesis are studied. To classify the 4 motions, we use flex sensors which is electrical resistance type sensor that can measure warp of muscle. The flex sensors are attached to the biceps brchii muscle and coracobrachialis muscle and the sensor signals are passed the sensing system. 4 motion of the forearm - flexion and extension, the pronation and supination are classified from this. Also position of forearm is measured from the classified signals. Finally, A two D.O.F prosthesis arm with RC servo-motor is designed to verify the validity of the algorithm. At this time, fuzzy controller is used to reduce the position error by rotary inertia and noise. From the experiment, the position error had occurred within about 5 degree.

• Journal of the Geological Society of Korea
• /
• v.54 no.5
• /
• pp.501-511
• /
• 2018

Geoparks are worth preserving in an environmentally and heritage. Monitoring and public attention are essential for the conservation and protection of geoparks. The use of Unmanned Aerial Vehicles and the Structure from Motion algorithm enables effective monitoring of geoparks that are difficult to manage due to their wide range of manpower, and various spatial data derived from SfM can be utilized to improve awareness of geoparks that have been lacking. In order to prove this, firstly, we created the 3D spatial data by using the UAV and the SfM algorithm, which is one of the National geoparks of the Hantan-Imjin River area. Using this 3D data for Virtual Reality and 3D printing. After that, we verified the possibility of promoting the geopark through a simple online survey. Finally, we propose a method to utilize all the generated data from each step to promote and research for geoparks.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.2
• /
• pp.99-105
• /
• 2019

Unlike typical a dynamic positioning (DP) system, a DP-assisted mooring system must determine a set point (SP) that can ensure a mooring tension safety range to prevent an excessive increase in mooring tension. In this paper, a new algorithm for determining the SP is suggested in order to reduce the tension on all the mooring lines. To determine the SP, a working area around the vessel is represented by a rectangular grid. Thus, the size of the grid area is limited considering the offset of a vessel with a mooring system. At each grid's nodes, the resultant tension from all the mooring lines is estimated using the time history of the tension and vessel's position. The results of static analyses for each grid position are used to estimate the global tension. Consequently, the SP is automatically selected as a position satisfying criterion for minimizing the total tension. In order to validate the suggested algorithm, a motion simulation with the control system in the time domain and a discussion of the results are presented.