• 한국구조물진단유지관리공학회 논문집
• /
• 제10권4호
• /
• pp.153-159
• /
• 2006

현재, 폴리머는 보수용 모르타르의 혼화재료로 주로 사용되고 있으며, 이러한 보수용 모르타르에는 폴리머 이외에 각종 혼화재료가 첨가되어 있다. 본 연구에서는 폴리머의 배합비율에 따라 보수용 모르타르에 미치는 영향과 동일한 EVA계 폴리머가 제조사가 다른 제품에 따라 미치는 영향을 비교하고자 모르타르의 굳기 전 특성 및 역학적 특성에 대하여 시험을 통하여 분석하였다. 시험결과 보수용 모르타르에 폴리머의 배합비율이 증가될수록 역학적 특성(압축강도, 휨 강도, 부착강도)이 개선되었으며, 또한 건조수축도 증가하였다.

• 대한건축학회논문집:구조계
• /
• 제34권5호
• /
• pp.13-18
• /
• 2018

In this research, regarding the type three blast furnace slag (BS) regulated by KS F 2563 and supplied to actual ready mixed concrete plant, the fineness on specification and actually measured fineness by Blain test were compared, and by applying the hydrometer method used for early prediction of concrete strength, the feasibility of the hydrometer method for acquisition inspection of BS was analyzed. Additionally, the influence of various fineness of BS on properties of cement mortar was also assessed. According to the experimental results of this research, correlation of fineness values between specification and actually measured data were not matched. In the case of the rapid evaluation method using hydrometer, a good relation was shown between the fineness data obtained from hydrometer and Blain test. furthermore, from the cement mortar properties test, there was a good relation was obtained between fineness data from rapid evaluation method by hydrometer and cement mortar properties, while there was no clear relation between fineness data from specification and cement mortar properties. Hence, as a qulity controlling method of BS fineness, a rapid evaluation method using hydrometer is suggested as a new method.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 추계 학술논문 발표대회
• /
• pp.131-132
• /
• 2014

In this study, an experiment was carried out using graphite, conductive nickel powder, copper bar, carbon fiber for evaluate the exothermic properties and heating reproducibility of the cement mortar containing conductive material. As a result, the conductive materials that interfere with heating reproducibility are present, and the optimal conductive materials exist in each input voltage.

• Advances in concrete construction
• /
• 제10권5호
• /
• pp.381-391
• /
• 2020

This study aimed to develop reference materials (RMs) for mortar that can simulate the initial flow characteristics with constant quality over a long period. Through the previous research on the development of RMs for cement paste, the combination of limestone, glycerol, and water was used as the basic matrix for developing RMs for mortar in this study. In addition, glass beads of three particle sizes (0.5, 1.0, and 2.0 mm) and ISO standard sand were selected as tentative candidates to derive fine aggregate substitutes. The mixture of glass beads could simulate the initial flow characteristics of mortar, but under the same mixing ratio, replicates showed an unstable tendency to indicate inconsistent values due to the generation of electrostatic properties between materials and equipment. On the other hand, the mixture using ISO standard Sand not only simulates the constant flow characteristics for a long period of time, but also shows stable results with little error in replicates. Therefore, limestone, glycerol, ISO standard sand, and water were finally determined as components that met the required properties of RMs for mortar. The effect of each component on the flow characteristics of RMs was analyzed. It was found that glycerol increased the cohesion between the particles of standard sand, resulting in a constant increase both in the plastic viscosity and yield stress. Both limestone and standard sand had a dominant effect on the yield stress. The relationships between various mortar mixing ratios and the corresponding mixing ratios of RMs were established. In addition, the results of the verification experiment showed that the rheological properties of the RMs obtained through the relationships correlated with various water/cement ratios and the fine aggregate volume fractions of mortar obtained with same manner. In other words, the RMs for mortar developed in this study can be used as standard samples because they can simulate the initial flow characteristics of mortar of various mixing ratios for a long period without any chemical changes.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2002년도 학술.기술논문발표회
• /
• pp.29-36
• /
• 2002

High fluid concrete unlike OPC concrete is made with various material, and the phase of fresh concrete is considerably different. In order to understand fluidity phase and mix properties of high fluid concrete, concrete is required to access as suspension structure which consists of aggregate and paste. The focus of this paper is to analyze the test results and quantify the effect of mix proportions of molar and fineness modulus of ,and on the properties of fresh mortar. The effect of water-binder ratio, sand-binder ration, content; of ggbs (by mass of total cementitious materials), and various contents of water reducing agent on the yield stress and plastic viscosity of the mix is studied. Based on the experimental results, the following conclusion; can be drawn: (1) The mixing time needed (or high fluid mortar was approximately two times more than that of ordinary portland mortar. (2) The fluidity phase of mortar could be explained by yield stress of mix and the fluidity of mortar. (3) As the content of ggbs increased, yield stress of mortar was decreased and plastic viscosity of it was increased. (4) For the high fluid mortar, it was appeared that sand-binder ratio should be below 1.5.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회 논문집(I)
• /
• pp.237-242
• /
• 1998

Covering mortar as a filter for permeable polymer concrete is necessary for good permeability from filtration continuously. Therefore, this paper is intended as an evaluation of the mechanical properties and permeability of permeable polymer concrete covered with polymer mortar as a filter. An optimum permeable polymer concrete is selected in various mix proportions, and three different polymer mortars were cast immediately following on the casting of the base permeable polymer concrete. And they are tested for compressive and flexural strengths, adhesion in tension, hardening shrinkage and permeability . From the test results, binder and filler contents in mix proportions had a great influence on the permeability of polymer concretes. The mechanical properties of permeable polymer concretes covered with polymer mortars using crushed stone are superior to other filters, and hardening shrinkage is the smallest in filters. It is apparent that adhesion between the base permeable polymer concrete and polymer mortar is affected by the degree of hardening shrinkage. From this study, proper mix proportions can be recommended in the consideration of properties of the permeable polymer concrete.

• 한국건축시공학회지
• /
• 제16권1호
• /
• pp.53-58
• /
• 2016

본 연구는 쓰레기 소각재 용융슬래그 미분말을 혼화재료로 사용하기 위한 연구로 소각재 용융슬래그 미분말을 혼입한 모르타르에 대한 연구를 수행한 것이다. 쓰레기 소각재 용융슬래그 미분말의 혼입율을 10, 20, 30, 40, 50%로 다양하게 한 후 굳지 않은 모르타르의 플로 특성과 재령 3, 7, 14, 28, 56일의 압축강도를 평가하였다. 실험결과 쓰레기 소각재 용융슬래그 미분말의 혼입율이 증가할수록 유동성이 증가하였고, 3일, 7일의 압축강도는 점진적으로 감소하였으나, 재령 28, 56일 압축강도는 증가하는 것을 알 수 있었다.

• 폴리머
• /
• 제32권6호
• /
• pp.555-560
• /
• 2008

폴리머를 혼입한 폴리머 시멘트 모르타르 및 콘크리트는 인장강도, 휨강도, 접착성, 수밀성, 내마모성 그리고 내약품성 등을 개선시키는데 우수한 효과가 있어 고성능이 요구되어지는 건축 구조물의 외장재, 바닥 마감재, 포장재, 방수재, 장식 코팅재, 그리고 보수재 등의 용도로 많이 사용되고 있다. 또한, 기존의 시멘트 콘크리트의 취약성을 보완하는 측면뿐만 아니라 보다 내구적이고 안정적인 구조재료의 역할을 할 수 있어 다양한 용도의 개발이 이루어지고 있다. 본 연구에서는 폴리머를 건축재료인 시멘트 콘크리트에 적용하기 위한 기초적 실험으로써 폴리머 시멘트 모르타르를 제작하여 그 특성을 파악하고 건축재료로서의 폴리머 이용 가능성을 확인하고자 하였다. 폴리머를 시멘트 모르타르에 혼입하여 적용해 본 결과, 보통 시멘트 모르타르에 비해 폴리머 시멘트 모르타르의 강도와 내구성 증진효과가 높게 나타나는 것을 알 수 있었다.

• 콘크리트학회지
• /
• 제8권6호
• /
• pp.163-172
• /
• 1996

최근 많은 양의 폐타이어가 발생됨에 따라 사회적 문제로 대두되고 있는 실정이며, 이에 대한 재활용은 각 분야에서 활발하게 연구되고 있다. 건설 분야에서는 폐타이어를 냉각 분쇄하여 만든 분말을 시멘트 콘크리트에 혼입하여 사용하는 연구가 많이 수행되고 있다. 시멘트 콘크리트에 폐타이어 분말을 혼입하여 사용할 때는 폐타이어 분말과 시멘트경화체 사이에서 접착성의 문제로 기초적 성질이 저감된다. 본 연구에서는 시멘트 모르터 내부에서 폐타이어 분말의 접착력을 증진시키기 위하여 시멘트 혼화용 폴리머 중의 하나인 스티렌 부타디엔 고무(SBR)라텍스를 사용하여 기초적 성질을 개선하고자 하였다. 실험결과 SBR 코팅 폐타이어 분말을 혼입한 시멘트 모르터는 코팅하지 않은 폐타이어 분말을 사용한 경우보다 기초적 성질이 개선되는 것으로 나타났으며, 또한 폴리머 시멘트비 10%를 사용한 SBR 라텍스 혼입 폴리머 시멘트 모르터의 경우에도 기초적 성질이 개선되었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.671-676
• /
• 1998

This study deals with the effect on penetration properties of siliceous ion througth the mortar applicated by the waterproofing coating materials of siliceous seler liquid type. The tests of properties for reinforcing effect in mortar substrate surface layer are five kinds of water permeability, absorption, compressive strength, surface layer strength, pH content and chemical attack effect. Water permeability of mortar coated siliceous sealer in very than that of plane mortar. compressive strength of mortar coated siliceous sealer in larger than that of plane mortar about 10%.