• Journal of the Optical Society of Korea
• /
• v.16 no.1
• /
• pp.1-5
• /
• 2012

This paper describes a 150-Mb/s monolithic optical receiver for plastic optical fiber link using a standard CMOS technology. The receiver integrates a photodiode using an N-well/P-substrate junction, a pre amplifier, a post amplifier, and an output driver. The size, PN-junction type, and the number of metal fingers of the photodiode are optimized to meet the link requirements. The N-well/P-substrate photodiode has a 200-${\mu}m$ by 200-${\mu}m$ optical window, 0.1-A/W responsivity, 7.6-pF junction capacitance and 113-MHz bandwidth. The monolithic receiver can successfully convert 150-Mb/s optical signal into digital data through up to 30-m plastic optical fiber link with -10.4 dBm of optical sensitivity. The receiver occupies 0.56-$mm^2$ area including electrostatic discharge protection diodes and bonding pads. To reduce unnecessary power consumption when the light is not over threshold or not modulating, a simple light detector and a signal detector are introduced. In active mode, the receiver core consumes 5.8-mA DC currents at 150-Mb/s data rate from a single 3.3 V supply, while consumes only $120{\mu}W$ in the sleep mode.

• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.176-179
• /
• 1989

The optimization of the monolithic pin-FET receiver is discussed, with emphasis on the sensitivity and bandwidth. The amplifier circuit, bias resistance, total input capacitance, and transconductance of FET for the 2 Gbps transmission are calculated.

• ETRI Journal
• /
• v.31 no.5
• /
• pp.622-624
• /
• 2009

This letter presents a compact 2.5 Gb/s burst-mode receiver using the first reported monolithic amplifier IC developed with 0.25 ${\mu}m$ SiGe BiCMOS technology. With optimum avalanche photodiode gain, the receiver module can obtain a fast response, high sensitivity and wide dynamic range, satisfying the overhead timing and various power specifications for a 2.5 Gb/s next-generation passive optical network (PON), as well as a legacy 1.25 Gb/s PON in the upstream.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.8
• /
• pp.52-59
• /
• 2007

In this paper, we analyzed and measured implant isolation characteristics for a 1.25 Gbps monolithic integrated hi-directional (M-BiDi) optoelectronic system-on-a-chip, which is a key component to constitute gigabit passive optical networks (PONs) for a fiber-to-the-home (FTTH). Also, we derived an equivalent circuit of the implant structure under various DC bias conditions. The 1.25 Gbps M-BiDi transmit-receive SoC consists of a laser diode with a monitor photodiode as a transmitter and a digital photodiode as a digital data receiver on the same InP wafer According to IEEE 802.3ah and ITU-T G.983.3 standards, a receiver sensitivity of the digital receiver has to satisfy under -24 dBm @ BER=10-12. Therefore, the electrical crosstalk levels have to maintain less than -86 dB from DC to 3 GHz. From analysed and measured results of the implant structure, the M-BiDi SoC with the implant area of 20 mm width and more than 200 mm distance between the laser diode and monitor photodiode, and between the monitor photodiode and digital photodiode, satisfies the electrical crosstalk level. These implant characteristics can be used for the design and fabrication of an optoelectronic SoC design, and expended to a mixed-mode SoC field.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.3
• /
• pp.34-38
• /
• 2000

This paper describes design, fabrication, and performance of an ultra-high-speed and low-noise MMIC (Monolithic Microwave Integrated Circuit) preamplifier for a 10 Gb/s optical receiver. The transimpedance type 3-stage MMIC preamplifier for ultra-high-speed and low-noise was designed using an AlGaAs/InGaAs/GaAs P-HEMTs(Pseudomorphic High Electron Mobility Transistors) with 0.15${\mu}{\textrm}{m}$ length T-shaped gate. To obtain broadband characteristics, we used the inductor peaking technique, and the gate width was optimized for low noise performance. Measurements reveal that the fabricated preamplifier has the high transimpedance gain of 60 ㏈Ω and 9.15 ㎓ bandwidth with the noise figure of less than 3.9 ㏈.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.2
• /
• pp.1-8
• /
• 2004

This paper describes the design of monolithic optical transceiver circuitry being used as a part of the fiber optic modules. It has been designed in 0.6 ${\mu}{\textrm}{m}$ 2-poly 3 metal silicon CMOS analog technology and operates at 155.52 Mbps(STM-1) data rates. It drives laser diode to transmit intensity modulated optical signal according to 155.52 Mbps electrical data from system. Also, it receives 155.52 Mbps optical data that transmitted from other systems and converts it to electrical data using photo diode and amplifier. To avoid noise and interference between transmitter and receiver on one chip, layout techniques such as special placement, power supply separation, guard ring, and protection wall were used in the design. The die area is 4 ${\times}$ 4 $\textrm{mm}^2$ and the estimated power dissipation is less than 900 ㎽ with a single 5 V supply.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.9
• /
• pp.11-17
• /
• 2004

This paper describes the implementation of monolithic optical transceiver circuitry being used as a part of the fiber optic modules. It has been fabricated in 0.6 ${\mu}{\textrm}{m}$ 2-poly 3-metal silicon CMOS analog technology and operates at 155.52 Mbps(STM-1) data rates. It drives laser diode to transmit intensity modulated optical signal according to 155.52 Mbps electrical data from system. Also, it receives 155.52 Mbps optical data that transmitted from other systems and converts it to electrical data using photo diode and amplifier. To avoid noise and interference between transmitter and receiver on one chip, layout techniques such as special placement, power supply separation, guard ring, and protection wall were used in the design. The die area is 4 ${\times}$ 4 $\textrm{mm}^2$, and it has 32.3 ps rms and 335.9 ps peak to peak jitter on loopback testing. the measured power dissipation of whole chip is 1.15 W(230 mW) with a single 5 V supply.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.5 s.347
• /
• pp.48-53
• /
• 2006

This paper describes the electrical characteristics of monolithic optical transceiver circuitry being used in the fiber optic modules. It has been designed and fabricated, and compared with two chips version transceiver when operates at 155.52 Mbps data rates. To avoid noise and interference between transmitter and receiver on one chip, layout techniques such as special placement, power supply separation, guard ring, and protection wall were used in the design. To compare the two kind of fiber optic modules using each chip, single chip version has similar properties to two chip version in the electrical characteristics as noise and others.