• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.2060-2060
• /
• 2011

This paper was investigated the frequency property for optimal operating conditions of mono-crystalline Si solar cell. An internal impedance of mono-crystalline Si solar cell was influenced frequency. An optimal operating conditions of solar cell was under about 10[kHz].

• 한국전기전자재료학회논문지
• /
• 제24권8호
• /
• pp.654-658
• /
• 2011

This paper was investigated the electrical properties for optimal operating conditions of monocrystalline silicon solar cell. The output of electricity for monocrystalline solar cell was investigated according to the distances between solar cell and halogen lamp and to the resistances by the variable resistor.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 반도체 재료 센서 박막재료 전자세라믹스
• /
• pp.85-88
• /
• 2004

Mono-crystalline silicon(mono-Si) is both abundant in our environment and an excellent material for Si device applications. However, single crystalline silicon solar cell has been considered to be expensive for terrestrial applications. For that reason, the last few years have seen very rapid progress in the research and development activities of layer transfer(LT) processes. Thin film Si layers which can be detached from a reusable mono-Si wafers served as a substrate for epitaxial growth. The epitaxial films have a very high efficiency potential. LT technology is a promising approach to reduce fabrication cost with high efficiency at large scale since expensive Si substrate can be recycled. Low quality Si can be used as a substrate. Therefore, we propose one of the major technologies on fabricating thin film Si substrate using a LT. In this paper, we study the LT method using the electrochemical etching(ECE) and solid edge.

• 반도체디스플레이기술학회지
• /
• 제12권3호
• /
• pp.47-51
• /
• 2013

Current research trends of solar cells has focused on the high conversion efficiency and low-cost production technology. Passivation technology that can be easily adapted to mass production. Therefore, this study conducted experiments with aim of the following two methods for the fabrication of high-efficiency crystalline silicon solar cells. In the first task, an attempt is formation of local Al-BSF to a number of locally doped dots to increase the conversion efficiency of solar cells to reduce the loss of $V_{oc}$ overcome. The second major task, rear surface apply in $Al_2O_3/SiN_x$ stack layer, $Al_2O_3$ prominent negative fixed charge characteristics. As the result of task, Local Al-BSF and $Al_2O_3/SiN_x$ stack layer applied to the p-type single crystalline silicon solar cells, the average $V_{oc}$ of 644mV, $I_{sc}$ of 918mV and conversion efficiency of 18.70% were obtained.

• 한국결정성장학회지
• /
• 제24권2호
• /
• pp.47-53
• /
• 2014

태양전지용 규소에는 단결정, 다결정, mono-like의 세 가지 재료가 사용 중에 있다. 첫 번째로, 단결정은 수율향상의 과제에 집중되고 있으며, 이것은 고액 계면의 형상이 주요 요인으로 알려지고 있다. 이에 대한 연구가 전산모사 등으로 집중되고 있다. 또한 결정과 도가니의 회전 속도가 고액 계면의 형상에 영향을 미치는 것이 확인 되었다. 다결정의 경우에는 결정립계의 역할이 매우 중요하므로 이에 대한 연구가 진행되는데, 이들을 특히 전기적으로 비활성적인 쌍정 입계로 전환하는 연구가 진행되고 있다. 성장 조건을 변경시켜 쌍정 입계로 바꾸어서 재료의 전기적 성질을 향상시키는 결과를 확인하였다. 또한 성장 공정에서 발생될 수 있는 오염을 줄이기 위한 노력은 상부의 Ar 가스의 흐름을 상향 조절하여 불순물의 용입을 줄임이 확인되었다. 다음으로 mono-like인 경우에는 측면으로부터 성장 되어 들어오는 다결정이 단결정의 분율을 저하 시키는 주요 요인이 되고 있다. 이에 대한 해결책으로 하부의 냉각 속도를 높이고 상부와 측면에 단열재를 보강하는 방안이 제시되고 있고, 하부에 놓는 seed의 orientation을 조절하여 측면으로부터 성장 되어 들어오는 다결정을 억제하는 방안이 효과가 있음이 확인 되고 있다.

• 반도체디스플레이기술학회지
• /
• 제12권3호
• /
• pp.41-46
• /
• 2013

Efficient and inexpensive solar cells are necessary for photo-voltaic to be widely adopted for mainstream electricity generation. For this to occur, the recombination losses of charge carriers (i.e. electrons or holes) must be minimized using a surface passivation technique suitable for manufacturing. Recently it has been shown that aluminum oxide thin films are negatively charged dielectrics that provide excellent surface passivation of silicon solar cells to attract positive-charged holes. Especially aluminum oxide thin film is a quite suitable passivation on the rear side of p-type silicon solar cells. This paper, it demonstrate the interfacial microstructure and electrical properties of mono-crystalline silicon surface passivated by $Al_2O_3$ films during firing process as applied for screen-printed solar cells. The first task is a comparison of the interfacial microstructure and chemical bonds of PECVD $Al_2O_3$ and of PEALD $Al_2O_3$ films for the surface passivation of silicon. The second is to study electrical properties of double-stacked layers of PEALD $Al_2O_3$/PECVD SiN films after firing process in the temperature range of $650{\sim}950^{\circ}C$.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.43.1-43.1
• /
• 2010

In the crystalline silicon solar cells, the full area aluminum_back surface field(BSF) is routinely achieved through the screen-printing of aluminum paste and rapid firing. It is widely used in the industrial solar cell because of the simple and cost-effective process to suppress the overall recombination at the back surface. However, it still has limitations such as the relatively higher recombination rate and the low-to-moderate reflectance. In addition, it is difficult to apply it to thinner substrate due to wafer bowing. In the recent years, the dielectric back-passivated cell with local back contacts has been developed and implemented to overcome its disadvantages. Although it is successful to gain a lower value of surface recombination velocity(SRV), the series resistance($R_{series}$) becomes even more important than the conventional solar cell. That is, it is a trade off relationship between the SRV and the $R_{series}$ as a function of the contact size, the contact spacing and the geometry of the opening. Therefore it is essential to find the best compromise between them for the high efficiency solar cell. We have investigated the optimal design for the local back contact by using PC1D simulation.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2012년도 춘계학술발표대회 논문집
• /
• pp.243-247
• /
• 2012

The paper focuses on an anti-reflection (AR) coating deposited by PECVD in silicon solar cell fabrication. AR coating is effective to reduce the reflection of the light on the silicon wafer surface and then increase substantially the solar cell conversion efficiency. In this work, we carried out experiments to optimize double AR coating layer with silicon nitride and silicon oxide for the silicon solar cells. The p-type mono crystalline silicon wafers with $156{\times}156mm^2$ area, 0.5-3 ${\Omega}{\cdot}cm$ resistivity, and $200{\mu}m$ thickness were used. All wafers were textured in KOH solution, doped with $POCl_3$ and removed PSG before ARC process. The optimized thickness of each ARC layer was calculated by theoretical equation. For the double layer of AR coating, silicon nitride layer was deposited first using $SiH_4$ and $NH_3$, and then silicon oxide using $SiH_4$ and $N_2O$. As a result, reflectance of $SiO_2/SiN_x$ layer was lower than single $SiN_x$ and then it resulted in increase of short-circuit current and conversion efficiency. It indicates that the double AR coating layer is necessary to obtain the high efficiency solar cell with PECVD already used in commercial line.

• 한국재료학회지
• /
• 제27권2호
• /
• pp.107-112
• /
• 2017

The BCBJ (Back Contact and Back Junction) or back-lit solar cell design eliminates shading loss by placing the pn junction and metal electrode contacts all on one side that faces away from the sun. However, as the electron-hole generation sites now are located very far from the pn junction, loss by minority-carrier recombination can be a significant issue. Utilizing Medici, a 2-dimensional semiconductor device simulation tool, the interdependency between the substrate thickness and the minority-carrier recombination lifetime was studied in terms of how these factors affect the solar cell power output. Qualitatively speaking, the results indicate that a very high quality substrate with a long recombination lifetime is needed to maintain the maximum power generation. The quantitative value of the recombination lifetime of minority-carriers, i.e., electrons in p-type substrates, required in the BCBJ cell is about one order of magnitude longer than that in the front-lit cell, i.e., $5{\times}10^{-4}sec$ vs. $5{\times}10^{-5}sec$. Regardless of substrate thickness up to $150{\mu}m$, the power output in the BCBJ cell stays at nearly the maximum value of about $1.8{\times}10^{-2}W{\cdot}cm^{-2}$, or $18mW{\cdot}cm^{-2}$, as long as the recombination lifetime is $5{\times}10^{-4}s$ or longer. The output power, however, declines steeply to as low as $10mW{\cdot}cm^{-2}$ when the recombination lifetime becomes significantly shorter than $5{\times}10^{-4}sec$. Substrate thinning is found to be not as effective as in the front-lit case in stemming the decline in the output power. In view of these results, for BCBJ applications, the substrate needs to be only mono-crystalline Si of very high quality. This bars the use of poly-crystalline Si, which is gaining wider acceptance in standard front-lit solar cells.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권10호
• /
• pp.447-450
• /
• 2003

This paper presents a process optimization of antireflection (AR) coating on crystalline Si solar cells. Theoretical and experimental investigations were performed on a double-layer AR (DLAR) coating of MgF$_2$/CeO$_2$. We investigated CeO$_2$ films as an AR layer because they have a proper refractive index of 2.46 and demonstrate the same lattice constant as Si substrate. RF sputter grown CeO$_2$ film showed strong dependence on a deposition temperature. The CeO$_2$ deposited at 40$0^{\circ}C$ exhibited a strong (111) preferred orientation and the lowest surface roughness of 6.87 $\AA$. Refractive index of MgF$_2$ film was measured as 1.386 for the most of growth temperature. An optimized DLAR coating showed a reflectance as low as 2.04% in the wavelengths ranged from 0.4${\mu}{\textrm}{m}$ to 1.1${\mu}{\textrm}{m}$. We achieved the efficiencies of solar cells greater than 15% with 3.12% improvement with DLAR coatings. Further details on MgF$_2$, CeO$_2$ films, and cell fabrication parameters are presented in this paper.