• Design & Manufacturing
• /
• v.2 no.1
• /
• pp.7-10
• /
• 2008

Restriking method is to add to process in order to get the correct size and high precision accuracy of product which is formed in pre-process. This method is widely used at bending work and drawing work. Restriking die is particularly design and used as restriking process is performed. Therefore, production cost is increasing as one process or a two process are added. In this paper, punches and die block of square shell drawing die which could be performed drawing work and restriking process by using only one die are designed in order to solve these factors. The structure of sectional die which can integrate drawing die and restriking die was developed.

• Design & Manufacturing
• /
• v.8 no.1
• /
• pp.14-18
• /
• 2014

Even though 3D press die design gains more attention everyday in Korea, there are shortages of infrastructure and proper environments for it. What is most needed is human resources development and 3D die design standardization, on which the pace of 3D die design adoption depends. This study focuses on 3D press die design process by looking into an instance in which 3D die design system had been used to sell dies to a company "S" in Japan.

• Design & Manufacturing
• /
• v.8 no.1
• /
• pp.5-9
• /
• 2014

This study is about 3D design for parts supporting copper pipes of wall-mounted air-conditioners manufactured by company "D" in Japan. Domestic press die manufacturers are obsessed with 2D die design and are afraid of taking risk with developing 3D die design and die manufacture. This hinders paradigm shift. In this study, the strip layout, which was already completed in the previous study, is altered by adding restriking. Based on the modified strip layout, the 3D die design is done in 15 processes.

• Design & Manufacturing
• /
• v.9 no.2
• /
• pp.16-19
• /
• 2015

In this paper, The experimental study on the crack during press forming of the door latch assembly for a vehicle door is performed. Length to be inserted into the conventional mold upper die punch is 20 mm, wherein the cracks are generated on the product surface and causes a secondary quality problem. In this study, the length to be inserted in the mold upper die punch 0 mm, 10 mm, 20 mm, which was changed to perform the experiment. Through the experiment, the length inserted into the mold can be seen that the upper die punch of the press forming conditions optimized when the 0 mm.

• Design & Manufacturing
• /
• v.15 no.1
• /
• pp.66-71
• /
• 2021

In this study, die turning injection(DTI) mold design for manufacturing reservoir fluid tanks used for cooling in-vehicle batteries, inverters, and motors was conducted based on multi-field CAE. Part design, performance evaluation, and mold design of the reservoir fluid tank was performed. The frequency response characteristics through modal and harmonic response analysis to satisfy the automotive performance test items for the designed part were examined. Analysis of re-melting characteristics and structural analysis of the driving part for designing the rotating die of the DTI mold were performed. Part design was possible when the natural frequency performance value of 32Hz or higher was satisfied through finite element analysis, and the temperature distribution and deformation characteristics of the part after injection molding were found through the first injection molding analysis. In addition, it can be seen that the temperature change of the primary part greatly influences the re-melting characteristics during the secondary injection. The minimum force for driving the turning die of the designed mold was calculated through structural analysis. Hydraulic system design was possible. Finally, a precise and efficient DTI mold design for the reservoir fluid tank was possible through presented multi-field CAE process.

• Design & Manufacturing
• /
• v.2 no.5
• /
• pp.21-24
• /
• 2008

On this study, injection molding product of rectangular tray structure with thickness 0.25mm and aspect ratio(length/thickness) approximately 150 conducted. Technical aspects were reviewed on mold-die design and injection molding conditions. To have a thin-membraned plastic part, short-shot, shrinkage, twist, whitening and flash problems were considered and resolved. After measuring products, validity of this study and future improvement were discussed.

• Design & Manufacturing
• /
• v.7 no.1
• /
• pp.23-27
• /
• 2013

Orchard sprayers, wide area dusters and multipurpose control cars are flagship products of Hansung T&I Ltd. Spray pumps are one of the essential parts for these products. But conventional belt pulleys for spray pumps are heavy and expensive, and they bring down the quality as well as productivity of the end-products. Therefore, this study focuses on mold design for aluminum die casting belt pulley and mold manufacture.

• Design & Manufacturing
• /
• v.16 no.2
• /
• pp.39-45
• /
• 2022

Sheet Metal Forming by Press Forming Process takes a lot of time and cost from mold design to manufacturing. Therefore, all of die-makers are continuously conducting research to reduce the number of mold processes or the size of blanks to reduce costs. In the case of Forming complex shapes such as automobile component, wrinkles and cracks occur, so draw beads are used. Draw beads play an important role in suppressing the inflow of materials and minimizing the size of blanks. Factors that affect material flow include draw bead, blank holding pressure, lubricant, and surface roughness of punch and die. Most of the factors affect friction. In this study, after classifying circular beads and rectangular beads in cylindrical drawing molds using the AutoForm analysis program, the factors affecting the material inflow were considered.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.149-153
• /
• 2008

The cavity of mold is exposed to high pressure during injection molding operation. Injection molded articles with deep depth are often demanded as design variety increases. Mold becomes weak and deformation increases as the mold depth increases. Thus the injection molds for deep depth articles should be designed to hold out high pressure or stress and large deformation. Through this study, equation for mold design was examined and suggested novel method to determine equation for mold design with deep depth. Novel equation developed in this study was consisted with cantilever and two points bending while previous equation was modified from just cantilever bending. The validity of novel equation was verified through computer simulation.

• Design & Manufacturing
• /
• v.2 no.3
• /
• pp.40-44
• /
• 2008

Shaving in sheet metal forming is defined as a finish process to make the sheared surface clean which was blanked or pierced in the previous shearing stage. In this study the new shaving technique is applied to the progressive operation. The specimen is automatically fed by continuous movement of the strip. Which improve the positioning accuracy higher. For this study a square part which consist of blanking and piercing is selected for investigation and the progressive die which includes pre-piercing, pierce-shaving, half-blanking and blank-shaving etc is prepared for specimens of steel sheet(SPCC) and aluminum alloy sheet(AL5052). Experiments are carried out for several working variables such as shaving allowance, pre-shearing clearance and relative half-blanking depth. Consequently it was confirmed that the shaving by progressive die can be successfully employed to produce the clean parts requiring shaving process and optimum working conditions for shaving SPCC and AL5052 sheet metal are shaving allowance of 0.2mm(1.3% of thickness) and pre-shearing clearance of 5%.