• Korean Chemical Engineering Research
• /
• v.50 no.5
• /
• pp.879-884
• /
• 2012

In this present study, Aspergillus niger NRRL 567 was cultivated on an inert support material and the effects of various fermentation parameters including temperature, nutrient solution pH, inoculation level, and moisture content were observed and optimized by one-factor-at-a-time (OFAT) and response surface methodology (RSM), sequentially. It was found that the incubation temperature of $30^{\circ}C$ with 75% moisture content, nutrient solution pH of 7.1 and inoculation level of $4.0{\times}10^6$ spores/ml were the most favorable. Again, fermentation parameters were optimized using RSM. The determined optimum condition is $26.5^{\circ}C$, pH 9.9, 75.1%, and $6.0{\times}10^6$ spores/ml. Under this optimized condition, A. niger NRRL 567 produced 118.8 g citric acid/kg dry peat moss at 72 hr. Maximum citric acid production of optimized condition by RSM represented a 1.6-fold increase compared to that obtained from control experiment.

• Korean Chemical Engineering Research
• /
• v.52 no.3
• /
• pp.302-306
• /
• 2014

The present study was carried out to optimize fermentation parameters for the production of cellulolytic enzymes through solid substrate fermentation of Trichoderma reesei and Aspergillus niger grown on wheat straw. A sequential optimization based on one-factor-at-a-time method was applied to optimize fermentation parameters including temperature, pH, moisture content and particle size. The results of optimization indicated that $40^{\circ}C$, pH 7, moisture content 75% and particle size between 0.25~0.5 mm were found to be the optimum condition at 96 hr fermentation. Under the optimal condition, co-culture of T. reesei and A. niger produced cellulase activities of 10.3 IU, endoglucanase activity of 100.3 IU, ${\beta}$-glucosidase activity of 22.9 IU and xylanase activity of 2261.7 IU/g dry material were obtained. Cellulolytic enzyme production with optimization showed about 72.6, 48.8, 55.2 and 51.9% increase compared to those obtained from control experiment, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.3
• /
• pp.258-267
• /
• 2017

In this study, pitch pine (Pinus rigida, PIR) and Mongolian oak (Quercus mongolica, QUM) pellets were fabricated with bark or/and drying waste liquor (DWL) of larch (Larix kaempferi, LAK) as an additive. Based on the results of fuel characteristics of the pellets, optimal conditions for producing the high-quality pellets were provided. In the analysis of chemical composition, bark contained holocelluose and lignin of 90% and over. DWL had 0.1% solid assumed to sugars which are generated from the oven-drying of LAK logs. QUM showed high ash content (2.2%) by containing of bark in the sawdust. Bark and DWL of LAK had high ash content of 4% and over. Calorific values of all specimens and additives were higher than that of the $1^{st}$-grade standard of wood pellets designated by NIFOS (18.0 MJ/kg). PIR and QUM pellets were fabricated with additive of 2 wt% based on the solid weight of oven-dried sawdust using a piston-type flat-die pelletizer, and thus ash content and calorific value of the pellets did not affect by the use of additive. Durability of the pellets increased with the use of additive. Durabilties of pellets, which were fabricated with bark as an additive and DWL as a controller of moisture content for sawdust, did not differ from those of pellets without additives and were lower than those of pellets either with bark or DWL. However, use of both bark and DWL for the production of wood pellets might be favorable because it can make a profit from the collection process of DWL. Based on the results of fuel characteristics of the pellets, QUM and PIR pellets were produced by a flat-die pelletizer. Moisture content (MC), bulk density and durability of the pellets improved with the use of additive. Particularly, sawdust MC of 10% and the addition of bark or DWL for PIR as well as sawdust MC of 12% and the addition of bark for QUM might be optimal conditions for the production of high-quality pellets. Except for the ash content of QUM pellets, other properties of PIR and QUM pellets exceeded the $1^{st}$-grade wood pellets standards of NIFOS.

• Asian-Australasian Journal of Animal Sciences
• /
• v.24 no.12
• /
• pp.1690-1698
• /
• 2011

Feedlot and in vitro ruminal experiments were conducted to assess the effects of saponin-containing surfactant applied during tempering of barley grain on cattle growth performance and on ruminal fermentation. In the feedlot experiment, treatments with three barley grain/barley silage based diets were prepared using barley grain at 7.7% moisture (dry, D), after tempering to 18% moisture (M), or after tempering with a saponin-based surfactant included at 60 ml/t (MS). Each treatment was rolled at settings determined previously to yield optimally processed barley. A total of 180 newly weaned British${\times}$Charolais steers were fed three diets in 18 pens for a 63-d backgrounding period and 91-d finishing period to determine feed intake, growth rate and feed efficiency. Cattle were slaughtered at the end of the experiment to measure the carcass characteristics. Tempering reduced (p<0.001) volume weight and processing index, but processing characteristics were similar between MS and M. Tempering increased (p<0.05) growth during backgrounding only, compared with D, but did not affect feed intake in either phase. During backgrounding, feed efficiency was improved with tempering, but during finishing and overall this response was only observed with the surfactant. Tempering did not affect carcass weight, fat content or meat yield. Surfactant doubled the proportion of carcasses grading AAA. In the in vitro experiment, barley (500 mg; ground to <1.0 mm or steam-rolled) was incubated in buffered ruminal fluid (40 ml) without or with surfactant up to 20 ${\mu}l/g$ DM substrate for 24 h. Surfactant increased (p<0.05) apparent DM disappearance and starch digestibility but reduced productions of gas and the volatile fatty acid and acetate:propionate ratio, irrespective of barley particle size. Compared with feeding diets prepared with non-tempered barley, tempering with surfactant increased the feed efficiency of feedlot steers. This may have arisen from alteration in processing characteristics of barley grain by surfactant rather than its direct effect on rumen microbial fermentation.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.6
• /
• pp.721-731
• /
• 2019

Air drying depends on species, density, dimension of wood, the geographical location of the air drying yard, and the meteorological factors of air drying site. If there are four seasons with large difference in temperature and humidity like in Korea, the research of the meteorological factors is required in air drying site. In this study, effective air drying days (EADD) of 24 regions in Korea were calculated by using the average monthly temperature, relative humidity, and wind speed. The EADD in 24 regions in Korea was ranged from 239 days to 291 days, with an average 265 days. This result is 5 days increased compared to the average of EADD calculated using the meteorological factors from 1955 to 1984. The results of multiple regression analysis on the EADD and meteorological factors showed that EADD affected in the order of temperature, relative humidity, and wind speed. As a result of dividing Korea into 4 zones of EADD, the zones of EADD were moved northward compared to previous study due to global warming. As basic data for predicting the moisture content (MC) distribution of Korean red pine logs during air drying conducted in Seoul, the average monthly temperature, relative humidity and wind speed for three years from 2016 to 2018 were presented, and the corresponding changes of the equilibrium MC were analyzed.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.50 no.6
• /
• pp.406-410
• /
• 2005

This study was conducted to establish the efficient protocols of the germination and cryopreservation of dehisced Korean ginseng seeds for long-term germ­plasm conservation. $GA_3$ and BA treated on seed for 24 hr facilitated germination at 5 and $10^{\circ}C$. Germination percentage of desiccated seeds was decreased under moisture content (MC) of below $7.2\%$. Dehisced ginseng seeds were dried under airflow of laminar floor cabinet and seed drying room. The high levels (more than $90\%$) of germination after cryogenic exposure were obtained after drying under vertical airflow of laminar floor for 12-30 hours (MC $10.6{\~}7.2\%$). Decrease in germination percentage of ginseng seeds due to desiccation damage and freezing injury was observed at MC of below $7.2\%$ and of above $12.1\%$, respectively. Therefore, MC of ginseng seeds need to be controlled with a range of $8{\~}10\%$ to avoid damages from both desiccation and freezing.

• Agricultural and Biosystems Engineering
• /
• v.3 no.2
• /
• pp.59-64
• /
• 2002

Odor generated during composting of livestock manure is mainly due to ammonia emission. Biofiltration is a desirable method to control composting odor. This study was conducted to analyze the efficiency of using fresh compost as a biofilter. A mixture of cattle manure and recycled compost was composted in a bin equipped with a suction-type blower. The exhaust gas was filtered through the fresh compost. Residence time was controlled by the flow rate of exhaust gas and the depth of filtering materials. At the aeration rate of 30 L/min(experiment I), ammonia reduction rate varied from 100% to -15% for biofilter A(residence time 56.5 s) and almost 100% for biofilter B(residence time 113 s). At the aeration rate of 30 L/min, the cumulative ammonia reduction rate was 80.5% for biofilter A and 99.9% for biofilter B. At the aeration rate of 50 L/min(experiment II), the lowest reduction rate showed a negative value of -350% on the 8th and 9th day for biofilter A(residence time 33.9 5), and 50% on the loth day for biofilter B(residence time 67.8s). At the aeration rate of 50 L/min, the cumulative ammonia reduction rate was 82.5% fur biofilter A and 97.4% for biofilter B. Filtering efficiency was influenced by residence time. The moisture content(MC) and total nitrogen(T-N) of the filtering material were increased by absorbing moisture and ammonia included in the exhaust gas, while pH was decreased and total carbon(T-C) remained unchanged during the filtering operation.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.3
• /
• pp.1-8
• /
• 1998

Western redcedar timber, 26 by 26cm in cross section and by 200cm long, was dried in a laboratory radio-frequency/vacuum kiln under 65torr of ambient pressure and a fixed frequency of 6.78MHz for the potential rapidly dry large timber. All process data were collected and saved in a computer through a data acquisition system. The temperature in the middle of timber was higher than temperature at the quarter point of timber length and thickness. Temperature gradients developed in the longitudinal and transverse direction of timber. The pressure in the middle of timber was higher than pressure at the quarter point of timber length. The pressure in the middle of timber was lower in the early stage of drying, and higher in the latter stage of drying than pressure at the quarter point of timber thickness. Power density was very highest during heating period and then gradually decreased. The drying curve was approximately linear and the total drying time was 27 hours from an initial moisture content(MC) of 48.6 percent to a final Me of 19.2 percent with only a few mild internal checks in the middle location of timber.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.6
• /
• pp.481-489
• /
• 2011

This study was conducted to evaluate the pressure treatment characteristics of Japanese red pine and Japanese larch skin timber with ACQ-2, CUAZ-2 and CuHDO-1. The effect of moisture content (MC) on preservative treatability was investigated for Japanese red pine sapwood and Japanese larch heartwood, and fixation characteristics of CCA alternatives was also evaluated. Japanese red pine sapwood, which was dried below 30 percent MC, was fully penetrated with preservatives, and minimum requirement of preservative retention for the hazard class H3 was achieved. Through measuring preservative retention gradient in Japanese red pine sapwood, it was confirmed that the retention gradient of CuHDO-1 was steeper than that of both ACQ-2 and CUAZ-2. In particular, it was intensified at a higher MCs of wood samples (25∼30%). Japanese larch heartwood did not meet the minimum requirement of penetration and retention for the hazard class H3 over the range of pretreatment MCs tested. With presteaming under $121^{\circ}C$ for 12 hours, the treatability of Japanese larch heartwood was enhanced to meet the minimum requirement for the hazard class H3. The fixation rate of copper was much more faster under drying condition compared with nondrying condition; more than 95% of copper were fixed in 3~6 days and 1 day under drying conditions in Japanese red pine sapwood and Japanese larch heartwood, respectively. After 3-week fixation period at ambient temperature, the amount of mobile copper in treated wood sample that remains available for leaching from treated wood was the highest in the wood samples treated with ACQ-2, followed by CuHDO-1 and CUAZ-2. It was proportional to the amount of copper in treating solution.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.37 no.3
• /
• pp.201-207
• /
• 2017

Hay-making is one of the most common forage preservation practices in livestock operations. The objective of hay-making is to minimize nutrient loss by shortening field drying time. Measuring the impacts of cutting height of forage crop is necessary to optimize hay production balancing yield and quality, in order to obtain substantial biomass increase through harvest of regrowth. This experiment was conducted to investigate the impact of cutting height of rye (Secale cereale L.) on drying rate and hay quality. Heading stage rye was harvested at 8cm or 15cm stubble heights. Hay was daily tedded at 09:00 and sampled at 09:00, 13:00 and 17:00 to determine moisture content (MC). After two month of preservation, CP (crude protein), ADF (acid detergent fiber), NDF (neutral detergent fiber), IVDMD (in vitro dry matter disappearance), TDN (total digestible nutrient), RFV (relative feed value), DM (dry matter) loss, visual scores and total fungi count were determined for estimation of hay quality. Cutting height at 15cm could enhance the drying rate and CP content (p<0.05), but also increases DM loss (p<0.05) compared to cutting at 8cm. Cutting heights did not affect ADF, NDF, IVDMD, TDN and RFV value (p>0.05). Visual scores of rye hays cutting at 8cm and 15cm, ranged from 83 to 85. Cutting at 8cm tended to maintain higher core bale temperature and fungal count than cutting at 15cm during preservation, but there was no significant difference.