• Journal of Internet Computing and Services
• /
• v.5 no.3
• /
• pp.45-56
• /
• 2004

In this paper, we propose ATM switch architecture including ALL type 2 switch which can efficiently transmit low-bit rate data, even if the network has many endpoints. We simulate the architecture of ATM switch fabric that is modeled in computer program and analyze the performance according to offered loads. ATM switch proposed in this paper can support cell switching for all types of m cells which consist of ALL type 1. ALL type 2, ALL type 3/4 and ALL type 5 cells. We propose two switch fabric methods; One supports the ALL type 2 cell processing per input port, the other global ALL type 2 cell processing for every input port. The simulation results show that the latter is superior to the former. But the former has a merit for easy implementation and extensibility. In this paper, the AAL Type 2 switch module which adapts the former method is designed using VHDL language and implemented in FPGA chip. The designed AAL Type 2 switch module operates at 52MHz. The proposed ATM switch fabric is widely applicable to mobile communication, narrow band services over ATM network and wireless ATM as well as general ATM switching fabric.

• Current Photovoltaic Research
• /
• v.7 no.4
• /
• pp.111-120
• /
• 2019

The output power of a crystalline silicon (c-Si) photovoltaic (PV) module is not directly the sum of the powers of its unit cells. There are several losses and gain mechanisms that reduce the total output power when solar cells are encapsulated into solar modules. Theses factors are getting high attention as the high cell efficiency achievement become more complex and expensive. More research works are involved to minimize the "cell-to-module" (CTM) loss. Our paper is aimed to focus on electrical losses due to interconnection and mismatch loss at PV modules. Research study shows that among all reasons of PV module failure 40.7% fails at interconnection. The mismatch loss in modern PV modules is very low (nearly 0.1%) but still lacks in the approach that determines all the contributing factors in mismatch loss. This review paper is related to study of interconnection loss technologies and key factors contributing to mismatch loss during module fabrication. Also, the improved interconnection technologies, understanding the approaches to mitigate the mismatch loss factors are precisely described here. This research study will give the approach of mitigating the loss and enable improvement in reliability of PV modules.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.3
• /
• pp.539-546
• /
• 2018

Recently, as the solar power generation market is rapidly increasing, interest is focused on research for minimizing the output of the solar cell module. The role of the power optimizer is important when inconsistencies occur in photovoltaic power generation. In the conventional system, centralized inverter method and microinverter method are mainly used. In this paper, we analyze the problem of power generation efficiency loss due to the incompatibility of existing system configuration methods. We also proposed a module - type power compensation method that can improve the mismatch caused by shading. The proposed module - based power optimizer is implemented and compared with the existing operation method. From the simulation result, it was confirmed that the efficiency of the proposed operation method is improved compared to the existing method.

• Current Photovoltaic Research
• /
• v.9 no.1
• /
• pp.17-21
• /
• 2021

In this study, the effect of water level and temperature on the power generation was investigated in a water tank with an aquavoltaic PV module to perform feasibility research for the development of salt farm aquavoltaic system. The silicon solar cell attached to the bottom of each water tank is a 1-cell mini module, and the underwater effects of the crystal phase (19.0~19.9% of single- & 17.9~19.9% of poly-crystalline) of the PV module were investigated, and power generation characteristics for water level (0~10 cm) and temperature (10~40℃) were analyzed. The deterioration coefficients according to the water level and temperature of each single- and poly-crystalline module were investigated at very similar levels such as, -2.01 %/cm and -2.02 %/cm, -0.50 %/℃ and -0.48 %/℃, respectively. Therefore, in salt farm aquavoltaic system, water levels need to maintain as low as possible, and heat-induced degradation is similar to those shown in general land, and no factors have been found to be affected by the underwater environment depending on the determination.

• Current Photovoltaic Research
• /
• v.4 no.3
• /
• pp.119-123
• /
• 2016

We discussed various cover glass substrates available for photovoltaic (PV) modules, and investigated the fabrication methods of light trapping structures for the efficiency enhancement of PV modules: wet and dry etching or laser and direct patternings. We also introduced the analysis of haze at etched glass surfaces as a function of wavelength and also presented a anti-reflection coating technology for PV module.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.04a
• /
• pp.27-30
• /
• 2009

In this paper, we introduce the status of certificate test on crystalline silicon photovoltaic module in Korea. Up to 3. 2009, about 149 models have passed certificate test under KS C IEC61215 standard. Most products are from Korea, Japan, China. And some are from USA, German and Taiwan. A few environmental test items' results and standard test methods will be discussed. The detail discussion will be shown in the following paper.

• 한국태양에너지학회:학술대회논문집
• /
• 2008.11a
• /
• pp.42-47
• /
• 2008

In this paper, we analyze the electrical characteristics of PV depending on distance among solar cells before and after lamination process. From the result, the PV module's maximum power increases about 3.37% when solar cells's distance is 10mm. And the maximum power increases up to 8.42% when solar cells's maximum distance is 50mm. It is assumed that PV module's surface temperature decreases because of increasing distance between solar cells that would give high power generation. Also, short distance between solar cell and frame result in contamination on glass. When considering reduced maximum power caused by contaminant, from that. we can fabricated PV module of lower cost with high performance.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.48.1-48.1
• /
• 2011

In this presentation, We monitored weather data, such as global irradiance, ambient temperature, temperature of PV module, relative humidity and windspeed for 2 years, for determining accelerated test condition. then, we determined the temperature limit of accelerated test through weather data and FEM analysis. Detailed procedures will be summarized in this work. After analysing outdoor stress such as thermal stress, we decided main failure modes and mechanisms of PV module, especially solder joint of ribbon wire. we carried out the measurement of material properties such as thermal expansion coefficient for planning of accelerated test. we designed accelerated test based on FEM analysis results. we carried out thermal cycling test with 1 cell mini module for 3 months. We monitored the change of electrical performance every 1 week such as Voc, Isc, Pmax, etc. and then, we analized the ribbon wire/electrode intefaces. Detailed results will be summarized in this work.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.23-24
• /
• 2011

In this paper, I performed the IEC test in crystalline photovoltaic module described in test standard. And sometimes I changed the test sequence and impact factors for testing modules. Comparing the current test trees in IEC 61215, some ideas are suggested in proper test sequence to guarantee the long-term durability for 25 years.. The detail discussion will be shown in the following paper.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.137-142
• /
• 2011

Individual solar cells must be connected together to give the appropriate current and voltage levels and they must also be protected from damage by the environment. [1] PV module consists of a glass/ polymer encapsulation/ solar cell string/ polymer encapsulation/ back sheet. Usually, encapsulation materials is used EVA(ethylene vinyl acetate), PVB(polyvinyl butyral), PO(polyolefin)sheet. This study is about fabrication of module using silicone material instead of above them. We got to know advantage that is fabrication time and efficiency of modules.