• 한국지반신소재학회논문집
• /
• 제20권4호
• /
• pp.113-124
• /
• 2021

도시화 및 경제성장에 따라 기존 매립지 등 기피 시설로 인식되어 있는 지상 환경기초시설 및 에너지생산 시설의 지하화가 중요한 사회적 이슈로 대두되고 있다. 대규모 플랜트 시설을 지하에 안전하게 건설하기 위해서는 제한적인 공간 레이아웃의 활용성을 높이고, 불필요한 기둥을 최소화해야 한다. 본 논문에서는 플랜트 시설을 지하화 할 경우 발생하는 작업의 제약여건, 조립 및 철거, 공정 계통의 연계성, 유지 보수 등의 문제를 해결하기 위하여 플랜트 모듈화 공법(파이프랙)에 대해 검토하였다. 복합플랜트의 지하 고집적 배치, 공간 레이아웃 활용성 향상 및 구조물 안정성 확보를 위해 다양한 하중조건(지진하중, 장치하중, 토압하중 등)을 적용한 플랜트 모듈 해석을 수행하였다. 또한, 작용하중과 부재가 견딜 수 있는 설계강도비 값을 검토하고 모듈 형상에 따른 안정성을 고려한 파이프랙 소재를 추출하였다. 다양한 경계조건에서의 해석 결과를 바탕으로 지하복합플랜트 건설 시 필요한 기본모듈의 최소 설치 간격 및 모듈 배치(안)에 관한 시사점을 도출하였다.

• Wind and Structures
• /
• 제5권5호
• /
• pp.393-406
• /
• 2002

Aerodynamic pressures and forces were measured on a model of a solar panel containing six slender, parallel modules. Of particular importance to system design is the aerodynamically induced torque. The peak system torque was generally observed to occur at approach wind angles near the diagonals of the panel ($45^{\circ}$, $135^{\circ}$, $225^{\circ}$ and $315^{\circ}$) although large loads also occurred at $270^{\circ}$, where wind is in the plane of the panel, perpendicular to the individual modules. In this case, there was strong vortex shedding from the in-line modules, due to the observation that the module spacing was near the critical value for wake buffeting. The largest loads, however, occurred at a wind angle where there was limited vortex shedding ($330^{\circ}$). In this case, the bulk of the fluctuating torque came from turbulent velocity fluctuations, which acted in a quasi-steady sense, in the oncoming flow. A simple, quasi-steady, model for determining the peak system torque coefficient was developed.

• Korean Journal of Mathematics
• /
• 제28권4호
• /
• pp.699-715
• /
• 2020

In this paper, we give estimates of the Hankel determinant H₂(1) in a novel class 𝓝 (𝜀) of analytical functions in the unit disc. In addition, the relation between the Fekete-Szegö function H₂(1) and the module of the angular derivative of the analytical function p(z) at a boundary point b of the unit disk will be given. In this association, the coefficients in the Hankel determinant b₂, b₃ and b₄ will be taken into consideration. Moreover, in a class of analytic functions on the unit disc, assuming the existence of angular limit on the boundary point, the estimations below of the modulus of angular derivative have been obtained.

• 한국군사과학기술학회지
• /
• 제12권6호
• /
• pp.704-710
• /
• 2009

In this study, a comparison study of flutter analysis for the AGARD 445.6 wing with wind turnnel test data has been conducted in the subsonic, transonic and supersonic flow regions. Nonlinear aeroelastic using FSIPRO3D which is a generalized user-friendly fluid-structure analyses have been conducted for a 3D wing configuration considering shockwave and turbulent viscosity effects. The developed fluid-structure coupled analysis system is applied for aeroelastic computations combining computational structure dynamics(CSD), finite element method(FEM) and computations fluid dynamics(CFD) in the time domain. MSC/NASTRAN is used for the vibration analysis of a wing model, and then the result is applied to the FSIPRO3D module. the results for dynamic aeroelastic response using different turbulent models are presented for several Mach numbers. Calculated flutter boundary are compared with the wind-tunnel experimental and the results show very good agreements.

• 전자공학회논문지D
• /
• 제36D권11호
• /
• pp.33-44
• /
• 1999

3차원 위상변이 마스크의 단차 효과를 분석하기 위해 투명 경계조건, 주기적인 경계조건, 및 연속조건을 가진 경계요소법을 광 리소그래피 공정 시뮬레이션에 새로이 적용하였으며, 해석적인 해와 참고문헌의 결과와 비교함으로써 구현된 모듈의 정확성을 검증하였다. 또한, 기존의 rigorous coupled wave analysis에 의한 방법에 비해 수렴성과 계산 시간 측면에서 경계요소법을 이용하는 것이 더 효율적임을 확인하였다. 끝으로 비교적 간단한 위상변이 마스크와 다층-위상변이 마스크에 대한 최적 설계 과정을 기술하였다.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.395-400
• /
• 2005

The ship hull part is always exposed to severe corrosive environments. Therefore, it should be protected in appropriate ways to reduce corrosion problems. So there are two effective methods in order to protect the corrosion of ship hull. One is the paint coating as a barrier between steel and electrolyte (seawater) and the other is the cathodic protection(CP) supplying protection current. In the conventional design process of the cathodic protection system the required current densities of protected materials have been used. However, the anode position of field or laboratory experiment for obtaining the required current density for CP is significantly different from anode position for real structures. Therefore, the recent CP design must consider the optimum anode position for potential distribution equally over the ship hull. The CP design companies in the advanced countries can obtain the potential distribution results on the cathodic materials by using the computer analysis module. This study would show how to approach the potential analysis in the field of corrosion engineering. The computer program can predict the under protection area on the structure when the boundary condition and analysis procedure are reasonable. In this analysis the polarization curve is converted to the boundary condition in material data.

• 한국실내디자인학회논문집
• /
• 제19권1호
• /
• pp.137-147
• /
• 2010

The purpose of this study is to research a method of creating a new type of boundary by repeated disposition of single unit of modularized membrane successively. In the contemporary architectural indoor space, more highly dimensional analysis of boundary is required and the necessity of establishing boundary of a new concept that may satisfy cultural value, social value and artistic value as a whole as well as aesthetic and functional merit has been increased. In order to create a membrane that may fulfil the requirements of the diversified programs of space like this, an approach of complicated mechanism and high-dimensional calculation are required. At this time, digital GA modelling, parametric modelling technique may expand its range of possibility. One thing to be noted at this juncture is that indefinite expandability involved in digital modelling technique, modelling by grid of absolute and relative coordinates and convenience of systematization may surpass limitation of analogue or simple numerical calculation being progressed in the past. And in order to create solid process including unit modelling or pattern formation, Precise calculation process of computer is necessitated inevitably.

• Geomechanics and Engineering
• /
• 제24권3호
• /
• pp.267-280
• /
• 2021

The research presented in this paper deals with dynamic stability analysis of the graphene nanoplatelets (GPLs) reinforced composite spinning disk. The presented small-scaled structure is simulated as a disk covered by viscoelastic substrate which is two-parametric. The centrifugal and Coriolis impacts due to the spinning are taken into account. The stresses and strains would be obtained using the first-order-shear-deformable-theory (FSDT). For Poisson ratio, as well as various amounts of mass densities, the mixture rule is employed, while a modified Halpin-Tsai model is inserted for achieving the elasticity module. The structure's boundary conditions (BCs) are obtained employing GPLs reinforced composite (GPLRC) spinning disk's governing equations applying principle of Hamilton which is based on minimum energy and ultimately have been solved employing numerical approach called generalized-differential quadrature-method (GDQM). Spinning disk's dynamic properties with different boundary conditions (BCs) are explained due to the curves drawn by Matlab software. Also, the simply-supported boundary conditions is applied to edges 𝜃=𝜋/2, and 𝜃=3𝜋/2, while, cantilever, respectively, is analyzed in R=R_i, and R₀. The final results reveal that the GPLs' weight fraction, viscoelastic substrate, various GPLs' pattern, and rotational velocity have a dramatic influence on the amplitude, and vibration behavior of a GPLRC rotating cantilevered disk. As an applicable result in related industries, the spinning velocity impact on the frequency is more effective in the higher radius ratio's amounts.

• 전자공학회논문지A
• /
• 제32A권9호
• /
• pp.114-120
• /
• 1995

It is important to test the various kinds of interconnect faults between chips on a card/module. When boundary scan design techniques are adopted, the chip to chip interconnection test generation and application of test patterns is greatly simplified. Various test generation algorithms have been developed for interconnect faults. A new interconnect test generation algorithm is introduced. It reduces the number of test patterns by half over present techniques. It also guarantees the complete diagnosis of mutiple interconnect faults.

• 한국CDE학회논문집
• /
• 제11권1호
• /
• pp.49-56
• /
• 2006

In this study, the modeling support system was developed which can make easy and fast FE-modeling and verify the results of static and durability analysis for the lower arm, one of the important parts in automobile suspension module. It took into account of the whole complicated design processes verifying the durability coefficients evaluated by fatigue analysis, which should be used to satisfy a design criteria. To guide the FE-modeling the drive page was constructed by using HTML and XML, which was based on expert's know-hows. It is able to integrate the processes to design the lower arm in practice, so that the standardization of its FE-Modeling is achieved, consequently. The 3 dimensional CAD's geometrical data were changed automatically into pre-defined shell elements under the concept of mesh-offset technique, and then welding elements were treated to connect between target and basic surfaces constructed by the shell elements. This system has also a user interface to control boundary and load ing conditions applied in performing of the static and durability analysis, in which many load cases can be applied simply with the MPCs driven by just few mouse clicks. These were implemented on the platform of MSC.Patran and utilized ANSYS, MSC.Nastran and MSC.Fatigue as the solver of the analysis performed. The developed system brings not only significant decreasing of man-hours required in FE-modeling process, but also obtaining of satisfied qualities in analyzed results. It will be integrated in a part of virtual prototyping module of the developing e-engineering framework.