• Journal of Animal Environmental Science
• /
• v.14 no.2
• /
• pp.75-80
• /
• 2008

High concentration of $NH_3$, $CO_2$, and lots of dust are found in modern densely raising stall system, as results, they provide a negative influence on animal and lamer health, and production ability. Therefore, it is necessary to keep clean the inside of stall air to increase the productivity. A wet type air cleaner has been developed to clean the stall air. The work principle is that the inside air are sucked through the fan, and the rotating discs make a water into a fineness spray and blows into the stall. The spray can take the dust, $NH_3$, and odor from the stall inside air and give back to the circulating water, which can be refreshed in 2 hours interval. In the Present study, we measured the $NH_3$, dust, odor, temperature and humidity in a swine stall that were installed two wet air cleaners with 700 fattening swine with on-mode and off-mode of wet air cleaners. In fall, the concentrations of $NH_3$ in off-mode stall were maximum 24 ppm and minimum 16 prm, and the average was 18.2 ppm. However in on-mode stall the $NH_3$ concentrations were maximum 7ppm and minimum 1ppm, and the average was 2.7ppm. The concentration of $NH_3$ in on-mode was 74% lower than off-mode stall. Odor was measured by olfactometer. In the off-mode stall, the odor unit was 3,800 OU/$m^3$, but in the on-mode stall the odor unit was 2,100 OU/$m^3$ Odor removal efficiency was about 45% in on-mode stall. The dust measure was divided into 3 categories, $PM_{10}$, $PM_{2.5}$ and $PM_{1.0}$. Whereas the $PM_{10}$ showed no significant differences between the tests, $PM_{2.5}$ and $PM_{1.0}$ in the fine particle range reduced remarkably in the on-mode.

• Particle and aerosol research
• /
• v.17 no.3
• /
• pp.43-54
• /
• 2021

Size distributions of atmospheric particulate matter (PM) and its water-soluble organic and inorganic components were measured between January and February 2021 at an urban site in Gwangju in order to identify the major factors that determine their size distributions. Their size distributions during the study period were mainly divided into two groups. In the first group, PM, NO₃^-, SO₄^2-, NH₄⁺ and water-soluble organic carbon (WSOC) exhibited bi-modal size distributions with a dominant condensation mode at a particle size of 0.32 ㎛. This group was dominated by local production of secondary water-soluble components under atmospheric stagnation and low relative humidity (RH) conditions, rather than long-range transportation of aerosol particles from China. On the other hand, in the second group, they showed tri-modal size distributions with a very pronounced droplet mode at a diameter of 1.0 ㎛. These size distributions were attributable to the local generation and accumulation of secondary aerosol particles under atmospheric conditions such as atmospheric stagnation and high RH, and an increase in the influx of atmospheric aerosol particles by long-distance transportation abroad. Contributions of droplet mode NO₃^-, SO₄^2-, NH₄⁺ and WSOC to fine particles in the second group were significantly higher than those in the first group period. However, their condensation mode contributions were about two-fold higher in the first group than in the second group. The significant difference in the size distribution of the accumulation mode of the WSOC and secondary ionic components between the two groups was due to the influx of aerosol particles with a long residence time by long-distance transport from China and local weather conditions (e.g., RH).

• Fashion & Textile Research Journal
• /
• v.2 no.2
• /
• pp.146-149
• /
• 2000

This study has been investigated the comparison of the seam strength of hand sewing with machine sewing using two kinds of sewing thread. On machine sewing, thread is used for sale, on hand sewing, thread is used for every fabric weft yarn. Breaking strength, efficiency and breaking mode of seams were examined under various sewing conditions using three kinds of fabric and three kinds of stitch type. The results obtained are as follows: The seam strength is not affected by sewing mechanism, but affected by a breaking mode : The type of slipped mode has a higher seam strength of hand sewing than that of machine sewing. When fabrics and threads were broken by a higher seam strength of machine sewing than that of hand sewing. Fabrics having low density using plain seam slipped more easily, so seam strength was greatly lesser. Fabrics having higher density had higher to seam strength. We should choose appropriate seams based on production, economy and aesthetics.

• Journal of Microbiology and Biotechnology
• /
• v.32 no.12
• /
• pp.1547-1552
• /
• 2022

β-Amyrin is a pentacyclic triterpene widely distributed in leaves and stems worldwide. The ability of β-amyrin to induce the production of reactive oxygen species (ROS) in microorganisms suggests its potential as an antimicrobial agent. Thus, this study aimed to elucidate the antibacterial mode of action of β-amyrin. We treated Escherichia coli cells with β-amyrin and found that it triggered ROS accumulation. Excessive stress caused by ROS, particularly hydroxyl radicals, induces glutathione (GSH) dysfunction. GSH protects cells from oxidative and osmotic stresses; thus, its dysfunction leads to membrane depolarization. The resultant change in membrane potential leads to the release of apoptotic proteins, such as caspases. The activated caspases-like protein promotes the cleavage of DNA into single strands, which is a hallmark of apoptosis-like death in bacteria. Apoptotic cells usually undergo events such as DNA fragmentation and phosphatidylserine exposure, differentiating them from necrotic cells, and the cells treated with β-amyrin in this study were positive for annexin V and negative for propidium iodide, indicating apoptosis-like death. In conclusion, our findings suggest that the antibacterial mode of action of β-amyrin involves the induction of ROS, which resulted in apoptosis-like death in E. coli.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.842-846
• /
• 1997

Micro-hole drilling (holes less than 0.5 mm in diameter with aspect ratios larger than 10) is gaining increased attention in a wide spectrum of precision production industries. Alternative methods such as EDM, laser drilling, etc. can sometimes replace mechanical micro-hole drilling but are not acceptable in PCB manufacture because they yield inferior hole quality and accuracy. The major difficulties in micro-hold drilling are related to wandering motions during the inlet stage, high aspect ratios, high temperature,etc. However, of all the difficulties, the most undesirable one is the increase of drilling force as the drill penetrates deeper into hold. This is caused mainly by chip related effects. Peck-drilling is thus widely used for deep hole drilling despite the fact that it leads to low productivity. Therefore, in this paper, a method of cutting force regulation is proposed to achieve continuous drilling. A proportional plus derivative (PD) and a sliding modecontrol algorithm will be implemented for controlling the spinle rotational frequeency. Experimental results will show that sliding mode control reduces the nominal cutting force and its variation better than the PD control, resulting in a number of advantages such as an increase in drill life, fast stabilization of the wandering motion, and precise positioning of the hole.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.3
• /
• pp.411-419
• /
• 2004

Titania particles are widely used as a photocatalyst to treat various contaminants in air and water. Titania particles were formed by vapor-phase oxidation of titanium tetraisopropoxide (TTIP) in a tube furnace between 773 and 1,273 K. The effect of process variables such as furnace temperature, flow rate of carrier air, and flow rate of sheath air on powder size and phase characteristics was investigated using a scanning mobility particle sizer (SMPS), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The size distribution of synthesized titania particles was characterized with mode diameter and peak concentration. The mode diameter ranging from 20 to 80 nm decreased with increasing flow rates of sheath air and carrier air, and increased with increasing furnace temperature. The peak concentration increased with increasing flow rates of sheath air and carrier air The best synthetic condition for high production rate can be derived from the experimental data set represented by mode diameter and peak concentration. The crystal structure of synthesized titania particles was found to be anatase phase, ensuring high photocatalytic potential.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.8
• /
• pp.1110-1117
• /
• 2001

Responses of the rumen fungus, Neocallimastix frontalis RE1, to long chain fatty acid (LCFA) were evaluated by measuring gas production, filter paper (FP) cellulose digestion and polysaccharidase enzyme activities. LCFA (stearic acid, $C_{18:0}$; oleic acid, $C_{18:1}$; linoleic acid, $C_{18:2}$ and linolenic acid, $C_{18:3}$) were emulsitied by ultrasonication under anaerobic condition, and added to the medium. When N frontalis RE1 was grown in culture with stearic, oleic and linoleic acid, the cumulative gas production, gas pool size, FP cellulose digestion and enzymes activities significantly (p<0.05) increased at some incubation times(especially, exponential phases of fungal growth, 48~120 h of incubation) relative to that for control cultures. However, the addition of linolenic acid strongly inhibited all of the investigated parameters up to 120 h incubation, but not after 168 and 216 h of incubation. These results indicated that stearic, oleic and linoleic acids tended to have great stimulatory effects on fungal cellulolysis, whereas linolenic acid caused a significant (p<0.05) inhibitory effects on the cellulolysis by the rumen fungus. These results are the first report of the effect of LCFAs on the ruminal fungi. Further research is needed to identify the mode of action of LCFAs on fungal strains and to verify whether or not ruminal fungi have ability to hydrate unsaturated LCFAs to saturated FAs. There was high correlation between cumulative in vitro gas production and fungal growth (94.78%), FP cellulose degradation (96.34%), CMCase activity(90.86%) or xylanase activity (87.67%). Thus measuring of cumulative gas production could be a useful tool for evaluating fungal growth and/or enzyme production by ruminal fungi.

• Microbiology and Biotechnology Letters
• /
• v.16 no.6
• /
• pp.450-456
• /
• 1988

For optimal production of L-tryptophan using a regulatory mutant of Escherichia coli the relationship between product formation and acid production was investigated. Experimental results showed that the production level of L-tryptophan was lowered as the specific acid production rate increased. In order to reduce the amount of acid produced during the fermentation, a controlled fed-batch fermentation was employed. In this fed-batch process, the feed rate of the nutrient feed medium was controlled in relation to the oxygen level in the culture and thus the growth of the cells was regulated in such n way that the oxygen demand of the culture could not exceed the oxygen sup-ply. When E. coli cells were cultivated in a controlled fed-batch mode of tormentor operation, the specific acid production rate was significantly reduced and L-tryptophan production was increased as much as five times that obtained in a conventional fed-batch fermentation.

• Journal of Drive and Control
• /
• v.14 no.2
• /
• pp.45-51
• /
• 2017

Semi-submersible drilling rigs are offshore plants that perform functions such as ocean exploration for oil and gas acquisition, drilling and production, and storage and unloading of crude oil and gas. Semi-submersible drilling rigs use watertight dampers as emergency buoyancy holders. Since the watertight damper is an emergency shutoff device, it is mainly driven by a pneumatic driving system that can operate without a power supply. The pneumatic driving system has highly non-linear characteristics due to compressibility of air and external disturbance such as static and Coulomb friction. In this paper, a new control algorithm is proposed for a watertight damper driving system based on the sliding mode control with a disturbance observer. To evaluate control performance and robust stability of the designed controller, the control results were compared with the results obtained using the state feedback controller. As a result, it was confirmed that the pneumatic driving system for driving the watertight damper using the sliding mode controller with a disturbance observer can obtain excellent control performance against the parameter changes and the disturbance input.

• Journal of Microbiology and Biotechnology
• /
• v.7 no.6
• /
• pp.409-416
• /
• 1997

Leuconostoc sp. LAB145-3A isolated from kimchi produced a bacteriocin which was active against food pathogens, such as Listeria monocytogenes, Enterococcus faecalis, and E. faecium. Bacteriocin production occurred during the early exponential phase of growth and was stable upto the late stationary phase of growth. Optimum conditions for bacteriocin production were $37^{\circ}C$ with an initial pH of 7.0. The bacteriocin of LAB145-3A was sensitive to proteases, but stable for solvents, pH change and heat treatment. It was stable even at autoclaving temperature for 15 min. The bacteriocin exhibited a bactericidal mode of action against Lactobacillus curvatus LAB170-12. The bacteriocin produced by Leuconostoc sp. LAB145-3A was purified by CM-cellulose cation exchange column chromatography and Sephadex G-50 gel filtration. The purification resulted in an approximate 10,000-fold increase in the specific activity. Approximately 4% of the initial activity was recovered. Purified bacteriocin exhibited a single band on the SDS-PAGE with an apparent molecular weight of 4,400 daltons. This bacteriocin was named leucocin K. Leuconostoc sp. LAB145-3A had two residential plasmids with molecular sizes of 23 kb and 48 kb. A comparison of plasmid profiles between LAB145-3A and its mutants revealed that the 23 kb plasmid (pCA23) was responsible for bacteriocin production and immunity to the bacteriocin in Leuconostoc sp. LAB145-3A.