• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.478.1-478.1
• /
• 2014

We investigated $MoO_3$ graded ITO electrodes for organic solar cells (OSCs) without PEDOT:PSS buffer layer. The effect of $MoO_3$ thickness on the electrical, optical, and structural properties of $MoO_3$ graded ITO anodes prepared by RF/DC magnetron co-sputtering system using $MoO_3$ and ITO targets was investigated. At optimized conditions, we obtained $MoO_3$ graded ITO electrodes with a low sheet resistance of 13 Ohm/square, a high optical transmittance of 83% and a work function of 4.92 eV, comparable to conventional ITO films. Due to the existence of $MoO_3$ on the ITO electrodes, OSCs fabricated on $MoO_3$ graded ITO electrode without buffer layer successfully operated. Although OSCs fabricated on ITO anode without buffer layer showed a low power conversion efficiency of 1.249%, OSCs fabricated on $MoO_3$ graded ITO electrode without buffer layer showed a outstanding cell performance of 2.545%. OSCs fabricated on the $MoO_3$ graded ITO electrodes exhibited a fill factor of 61.275%, a short circuit current of 7.439 mA/cm2, an open circuit voltage of 0.554 V, and a power conversion efficiency of 2.545%. Therefore, $MoO_3$ graded ITO electrodes can be considered a promising transparent electrode for cost efficient and reliable OSCs because it could eliminate the use of acidic PEDOT:PSS buffer layer.

• Journal of the Korean Chemical Society
• /
• v.30 no.4
• /
• pp.345-351
• /
• 1986

Monoxo-bridged binuclear molybdenum(V) complex, $[Mo_2O_3\;(bipy)_2\;(NCS)_4]$ in aqueous acetone mixture produces the corresponding dioxo-bridged binuclear molybdenum(V) complex, $MoO_4(bipy)_2(NCS)_2$. The rate of conversion of $[Mo_2O_3(bipy)_2(NCS)_4]$ to $MoO_4(bipy)_2(NCS)_2$ has been measured by spectrophotometric method. The rate of formation of dioxo-bridged binuclear molybdenum(V) complexes with solvent water follows the rate law, rate = k$[Mo_2O_3(bipy)_2(NCS)_4]\;[H_2O]$. The reaction mechanism for the formation of dioxo-bridged complex is discussed. The observed negative volume of activation shows that the complex is strongly attracted to the solvent molecules at transition state.

• Journal of the Korean Chemical Society
• /
• v.14 no.2
• /
• pp.141-145
• /
• 1970

The reduction of Mo-thiocyanate (V) complex on dropping mercury electrode has been studied at ionic strength 0.6 with pH less than 2.3. D-C polarogram obtained from acidic solutions are reversible, diffusion controlled current. The electrode reaction of Mo-thiocyanate(V) may be represented as follows. $MoO(SCN)_3\;+\;2H^+\;+\;2e\;{\to}\;Mo(SCN)_2{^+}\;+\;H_2O\;+\;SCN^-$From this reaction, the half wave potential assumed to be $E_{1/2}\;=\;E_0'\;-\;0.059\;pH\;-\;0.03\;log{\;frac{[Mo(SCN)_2{^+}][SCN^-]}{[MoO(SCN)_3]}}$Considering the dissociation of this complex, however, it was estimated that the electrode reaction may be written by. $MoO^{+3}\;+\;3SCN^-\;+\;2H^+\;+\;2e\;{\to}\;Mo(SCN)_2{^+}\;+\;SCN^-\;+\;H_2O$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.232-235
• /
• 1999

In this paper, We described the effect of $MoO_3$ Addition and firing temperature on the microwave dielectric properties of $BiNb0_4$ ceramics. The specimens prepared by conventional mixed method was addicted by 0 - 0.03 wt% $MoO_3$ and fired at 860 - $950^{\circ}$ for 3hr. Density increased when $MoO_3$ is below O.Olwt% but decreased when over O.Olwt%. $BiNb0_4$ ceramics addicted with CuO 0.03wt % and $MoO_3$ 0.01 wt% showed microwave dielectric properties, Dielectric constant 37.5, Quality factor[Qx$f_0$]5500, Temperature coefficient of resonance frequency 15ppm/$^{\circ}$

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.94-97
• /
• 2002

Phase transitions of the $Sm_{2}(MoO_{4})_{3}$ single crystal were studied through thermal analysis, x-ray methods and SEM/EDS. $Sm_{2}(MoO_{4})_{3}$ undergoes the ferroelastic and ferroelectric phase transition at $198^{\circ}C$. With increasing temperature, the second phase transition occurs at $928^{\circ}C$. From TG analysis, the mass loss of $Sm_{2}(MoO_{4})_{3}$ exhibits an anomalous behavior at about $650^{\circ}C$ and the curves increased monotonically to $1132^{\circ}C$. SEM and EDS show that the escape of ${MoO_{4}^{2-}$ tetrahedra from the lattice of $Sm_{2}(MoO_{4})_{3}$ increase above $928^{\circ}C$, so $Sm_{2}(MoO_{4})_{3}$ has a very rough surface and internal cracks.

• Resources Recycling
• /
• v.31 no.1
• /
• pp.29-36
• /
• 2022

The hydrogen reduction behavior of molybdenum oxides was studied using a horizontal-tube reactor. Reduction was carried out in two stages: MoO₃ → MoO₂ and MoO₂ → Mo. In the first stage, a mixed gas composed of 30 vol% H₂ and 70 vol% Ar was selected for the MoO₃ reduction because of its highly exothermic reaction. The temperature ranged from 550 to 600 ℃, and the residence time ranged from 30 to 150 min. In the second step, pure H₂ gas was used for the MoO₂ reduction, and the temperature and residence time ranges were 700-750 ℃ and 30-150 min, respectively. The hydrogen reduction behavior of molybdenum oxides was found to be somewhat different between the two stages. For the first stage, a temperature dependence of the reaction rate was observed, and the best curve fittings were obtained with a surface reaction control mechanism, despite the presence of intermediate oxides under the conditions of this study. Based on this mechanism, the activation energy and pre-exponential were calculated as 85.0 kJ/mol and 9.18 × 10⁷, respectively. In addition, the pore size within a particle increases with the temperature and residence time. In the second stage, a temperature dependence of the reaction rate was also observed; however, the surface reaction control mechanism fit only the early part, which can be ascribed to the degradation of the oxide crystals by a volume change as the MoO₂ → Mo phase transformation proceeded in the later part.

• Journal of Korean Society for Atmospheric Environment
• /
• v.8 no.1
• /
• pp.58-67
• /
• 1992

For removing $NO_x$ and $SO_x$ from the flue gases emitted from stationary sources, $V_2O_5-MoO_3/TiO_2$ catalysts were prepared by the conventional impregnation method (aqueous solution) and a sort of surface fixation method(nonaqueous solution) as reported excellent reproducibility catalysts. And these catalysts observed their catalytic activities as well as their surface properties. V-Mo-O oxide, prepared from nonaqueous solution of $VOCl_3$ and $Mo(CO)_6$ and aqeous solution method, was supported as amorphous state by XRD and SEM measurements. The infrared spectra of fresh and used catalysts showed that in used catalysts, V=O bands decreased and new bands of vanadium oxysulfate bands were very sensitive. So the catalysts prepared from nonaqueous solution may bring about the high activity. Results from catalytic activity measurements at 350$^\circ$C, in the presence of $SO_2, NO$ conversion was more increased than in absence of $SO_2$. As the $MoO_3$ was added to $V_2O_5/TiO_2 system, SO_2$ conversion increased. It found that from the results, $V_2O-5-MoO_3/TiO_2$ catalysts prepared from an nonaqueous solution may bring about the high activity for both the reaction of NO and $SO_2$ removal.

• Korean Journal of Materials Research
• /
• v.9 no.11
• /
• pp.1144-1147
• /
• 1999

The effect of the heat treatment on electrochromic properties of $\textrm{MoO}_3$ thin films is investigated by studing optical modulation, optical density, response time, and cyclic voltammetry. From the results of XRD analysis, heat-treated at $450^{\circ}C$ in air for 1 hour Moo3 thin films are found to be crystalline while as-deposited and heat- treated at low temperature ($\leq\;300^{\circ}C$) film are amorphous. The electrochromic devices using as-deposited $\textrm{MoO}_3$ films exhibit good electrochromic properties compared to those using the heat treated $\textrm{MoO}_3$ films. It has shown that the heat-treatment affected the reversible color change and the electrochromic properties of $\textrm{MoO}_3$ films.

• Journal of the Korean Ceramic Society
• /
• v.32 no.9
• /
• pp.1085-1091
• /
• 1995

Molybdenum disilicide (MoSi2) was synthesized from Mo, MoO3, Si and Al powders by self-propagating high temperature synthesis (SHS). The effect of processing parameters such as Mo/MoO3 molar ratio, Ar gas pressure in the reactor and pressing pressure of compacts in synthesis of MoSi2 were investigated. h-MoSi2 was transformed into t-MoSi2 with increasing the Mo/MoO3 mole ratio, and only t-MoSi2 phase was identified above 3.5 : 1 (molar ratio). The synthesized phases did not change with the variation of Ar gas pressure and pressing pressure of compacts. It was found that the combustion temperature was above 2,50$0^{\circ}C$. The products were separated into MoSi2 (s) and $\alpha$-Al2O3 by the difference of their specific grativities. Bending strength, hardness and density of sintered specimen exhibited 82 MPa, 5.368 GPa and 5.43 g/㎤, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.12
• /
• pp.1363-1368
• /
• 1998

Mo/γ-Al2O3 catalysts were prepared by impregnation method in various conditions to identify the states of surface Mo species. TPR (Temperature-Programmed Reduction) and Raman spectroscopy were applied to analyze the surface Mo species. TPR analysis revealed that MoO3 was reduced to Mo through MoO2, the intermediate state and the increase of Mo loading enhanced the reducibility of Mo oxide till the formation of monolayer coverage. High temperature calcination induced oxygen defects in MoO3 giving their unstable states for easier reduction. Raman spectroscopy analysis showed that the increase of Mo loading induced the polymeric Mo oxide.