• 반도체디스플레이기술학회지
• /
• 제2권4호
• /
• pp.31-35
• /
• 2003

We present a formation technique of thin film heater for heat transfer components. Thin film structures of Cr-Si have been prepared on top of alumina substrates by magnetron sputtering. More samples of Mo thin films were prepared on silicon oxide and silicon nitride substrates by electron beam evaporation technology. The electrical properties of the thin film structures were measured up to the temperature of $500^{\circ}C$. The thickness of the thin films was ranged to about 1 um, and a post annealing up to $900^{\circ}C$ was carried out to achieve more reliable film structures. In measurements of temperature coefficient of resistance (TCR), chrome-rich films show the metallic properties; whereas silicon-rich films do the semiconductor properties. Optimal composition between Cr and Si was obtained as 1 : 2, and there is 20% change or less of surface resistance from room temperature to $500^{\circ}C$. Scanning electron microscopy (SEM) and Auger electron spectroscopy (AES) were used for the material analysis of the thin films.

• 한국표면공학회지
• /
• 제46권1호
• /
• pp.16-21
• /
• 2013

CIGS (Cu-In-Ga-Se) films were deposited on the Mo coated soda lime glass (Mo/SLG) by RF magnetron sputtering using a single sintered target with different chemical compositions. Heat treatment of the CIGS films were carried out under three different conditions, 1step ($350^{\circ}C$ for 2 hour and $550^{\circ}C$ for 2 hour) and 2step ($350^{\circ}C$ for 1 hour and $550^{\circ}C$ for 1 hour). In the case of CIGS films post-annealed on 2step method, grain size remarkably increased compared to other methods, indicating that chemical composition [Cu/(Ga+In) = 1] of CIGS films was same as CIGS target. After heat treatment by 2step method, band gap energy of the CIGS film deposited at RF 80 W showed 1.4 eV which is broadly similar to identical band gap energy (1.2 eV) of CIGS film prepared by evaporation method. Therefore, 2step heat treatment method could be expected to low temperature process.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.388-388
• /
• 2010

Molybdenum oxide thin films were deposited on p-type Si(100) by an RF magnetron sputtering method. The physical and chemical properties of these films were studied with X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) techniques. The thickness of molybdenum oxide thin films was measured by spectroscopic ellipsometer (SE) and the thickness was about 200 nm. As the oxygen gas pressure increased, the thickness was decreased, the phases of the thin films were changed, and the amount of metallic Mo decreased but the contents of $Mo^{6+}$ species increases.

• 한국표면공학회지
• /
• 제44권6호
• /
• pp.264-268
• /
• 2011

The Molybedenium thin film is generally used on back contact material of CIGS solar cell due to low electrical resistivity and stable thermal expansion coefficient. The Mo thin films deposited on si wafer by the magnetron sputtering method. The research focused on the variation of electrical resistivity of films which deposited with various working pressure at the target power of 2.0 kW(8.4 W/). The lowest resistivity of Mo thin film showed $9.0{\mu}O$-cm at pressure of 1.5 mTorr. However, working pressure increasing up to 50 mTorr, resistivities were highly increased. The results showed that the conductivity of Mo films depended on growing structures and defects in deposition process. Surface morphology, porosity, grain size, oxidation, and bonding structures were analysed by SEM, AFM, spectroscopic ellipsometry (SE), XRD, and XPS.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.88-88
• /
• 2010

We synthesized molybdenum thin films deposited by RF magnetron sputtering and physicochemical analysis was performed. The physical and chemical properties of these films were examined with X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The obtained film at the oxygen ratio of 0% showed crystallinity of cubic Mo(110) phase. After the oxygen ratio increased more than 5% in the sputter gas, the molybdenum films were formed as an amorphous phase. The thickness of the Mo thin film was drastically decreased from 1000 nm to ca 70 nm after introduction of oxygen in the sputter gas confirmed by spectroscopic ellipsometer (SE) and scanning electron spectroscopy (SEM). The calculated band gap of the film deduced from SE data increased from 3.17 to 3.63 eV by addition of oxygen in the sputter gas. The roughness of the Mo film was examined with atomic force microscopy (AFM) and it was dramatically decreased by introducing of oxygen during sputtering. XPS results revealed that the ratio of metallic Mo species in the film decreased by the contents of Mo(VI) species increased at the ratio of oxygen increased in the sputter gas and fully oxidized at low content of oxygen in the sputter gas.

• 한국진공학회지
• /
• 제2권4호
• /
• pp.507-514
• /
• 1993

The solid state reaction of Mo/Si multilayer thin films produced by RF magnetron sputtering technique was examine dusing differential scanning calorimetry (DSC) and x-ray diffraction, and explained in view of two concepts, effective drivig force and effective heat of formation. In constant scanning rate DSC, there were two exothermic peks which corresponded to the formation of h-MoSi2 and t-MoSi2 , respectively. The activation energyfor theformation of h-MoSi2 was 1.5eV , and that of t-MoSi2 was 7.8eV. Nucleation wa stherate controlling mechanism for each of the silicide formation. Amorphous phase was not formed , which was consistent withtheprediction by the concept of effective driving force. h-MoSi2 the first crystalline phase, was considered to have lower interfacial free energy than t-MoSi2 and by increasing temperature it was transformed into more stable t-MoSi2.

• 한국진공학회지
• /
• 제6권2호
• /
• pp.143-150
• /
• 1997

본 연구에서는 1000$\AA$두께의 Molybdenum화합물(Mo, Mo-N,$MoSi_2$, Mo-Si-N)의 Cu에 대한 확산방지막으로서의 특성을 면저항측정장비(four-point-probe), XRD, XPS, SEM, RBS 분석을 통하여 조사하였다. 각 박막층은 dc magnetron sputtering장비를 이용하 여 증착되었고 $300^{\circ}C$-$800^{\circ}C$의 온도구간에서 30분동안 진공열처리하였다. Mo 및 $MoSi_2$ 방지 막은 낮은 온도에서 확산방지막으로서의 특성파괴를 보였다. 결정립계를 통한 Cu의 확산과 Mo-실리사이드내의 Si의 Cu와의 반응이 그 원인인 것으로 사료된다. 질소를 첨가한 시편의 경우 확산방지특성 파괴온도는 Mo-N방지막의 경우 $650^{\circ}C$-30분, Mo-Si-N방지막의 경우 $700^{\circ}C$-30분으로 향상되었다. Cu와 Si의 확산은 방지막의 결정립계를 통하여 더욱 빠르게 확 산된다. 따라서 증착시 결정립계를 질소와 같은 물질로 채워 Cu와 Si의 확산을 저지할 수 있을 것으로 사료된다. 본 실험결과에서의 질소첨가는 이와 같은 stuffing 효과외에도 Mo- 실리사이드 박막의 결정화 온도를 다소 높인 것으로 나타났고, 그 결과 결정립계의 밀도를 감소시켜 확산방지막으로서의 특성을 향상시킨 것으로 사료된다. 또한 질소첨가는 실리사이 드내의 금속과 실리콘과의 비를 변화시켜 확산방지막의 특성에 영향을 미친 것으로 보인다. 본 실험에서 조사된 확산방지막 중에서는 Mo-Si-N박막이 Cu와 Si간의 확산을 가장 효과적 으로 저지시킨 것으로 나타났으며 $650^{\circ}C$-30분까지 안정한 특성을 보였다.

• 한국표면공학회지
• /
• 제55권2호
• /
• pp.77-83
• /
• 2022

Nanocrystalline MoN coatings were prepared by inductively coupled plasma magnetron sputtering (ICPMS) changing the plasma power from 0 W to 200 W. The properties of the coatings were analyzed by x-ray diffraction, field emission scanning electron microscopy, atomic force microscopy, nanoindentation tester and semiconductor characterization system. As the ICP power increases, the crystal structure of the MoN coatings changed from a mixed phase of γ-Mo₂N and α-Mo to a single phase γ-Mo₂N. MoN coatings deposited by ICPMS at 200 W showed the most compact microstructure with the highest nanoindentation hardness of 27.1 GPa. The electrical resistivity of the coatings decreased from 691.6 μΩ cm to 325.9 μΩ cm as the ICP power increased.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 춘계학술대회 논문집
• /
• pp.73-74
• /
• 2015

본 연구에서는 상호간의 고용도가 없는 Mo, Cu 재료의 합금화가 용이하도록 기계적 합금화법(Mechanical Alloying)을 이용하여 Mo-Cu 합금분말을 제조하였고, 준안정상태의 구조의 유지가 가능한 방전 플라즈마 소결법(Spark Plasma Sintering)을 이용하여 합금타겟을 제작하였다. Mo-Cu 박막을 제작하기 위해서 합금타겟을 이용하였고 스퍼터링 공정을 진행하여 박막을 제작하였다. 그 결과 Mo-10wt%Cu 단일타겟을 이용하여 제작한 박막의 경우 Ar : N 분위기에서 27.7GPa 로 가장 높은 경도값을 가지는 것을 확인하였다. 또한 Mo-5wt%Cu 단일타겟을 이용하여 Ar : N 분위기에서 제작한 박막은 건식조건에서의 마찰계수값이 0.69 로 가장 낮은 것을 확인할 수 있었으며 윤활조건(GF4)에서는 Mo-10wt%Cu 단일타겟을 이용하여 Ar : N 분위기에서 제작한 박막이 0.56 으로 가장 낮았다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1998년도 제14회 학술발표회 논문개요집
• /
• pp.41-41
• /
• 1998

Rare earth metal films have been used as a buffer layer for growing ferroelectric t thin film or a seed layer for magnetic multilayer. But when it was deposited on s semiconductor substrates for the application of magneto-optic (MO) storage media, it i is difficult to exactly measure magnetic cons떠nts due to shunting current, and so it n needs to grow metal films on insulator substrate to reduce such effect. Recently, it w was reported that ultra-thin Pt layer were epitaxially grown on A12O:J by ion beam s sputtering in 비떠 high vacuum and it can be used as a seed layer for the growth of C Co-contained magnetic multilayer. In this stu$\phi$, Pt thin film were epi떠xially grown on AI2D3 ($\alpha$)OJ) by RF magnetron s sputtering. The crystalline structure was analyzed by transmission electron microscope ( (TEM) and Rutherford Back Scattering (RBS)/Ion Channeling. In TEM study, Pt was b believed to be twinned on AI잉3($\alpha$)01) su$\pi$ace about Pt(ll1) plane.Moreover, RBS c channeling spectra showed that minimum scattering yield of Pt(111)/AI2O:J(1$\alpha$)OJ) was 4 4% and Pt(11J)/AI2D3($\alpha$)OJ) had 3-fold symmetry.