• Journal of the Korean Institute of Navigation
• /
• v.25 no.4
• /
• pp.435-442
• /
• 2001

A new technique to grow a manganese-doped zinc-sulfide(ZnS：Mn) has been proposed using the repeated deposition of the Hot Wall method. The optical characteristics and crystallinity for the ZnS and ZnS：Mn thin films deposited on a quartz glass substrate by the method were investigated. Also, The ZnS：Mn thin film elcetroluminescent devices were fabricated by the method to study luminescence characteristics. All films showed (111)-oriented cubic structure. By the repeated deposition, the deposition rates were decreased, and the optical characteristics and crystalline properties were improved, which clarifies that the method is effective to deposit the thin films with good crystallinity Futhermore, the crystallinity was more improved by the doping of Mn. Only one peak emission at around 585nm originating from Mn luminescent center is observed In the photoluminescent and electroluminescent spectra of ZnS：Mn films and the luminance of the ZnS：Mn-based thin film electroluminescent devices was obtained below 60cd/$m^2$ . The optical and crystalline properties, luminescence characteristics are discussed in terms of the effects of the repeated deposition and Mn-doping.

• Electrical & Electronic Materials
• /
• v.10 no.10
• /
• pp.1005-1010
• /
• 1997

ZnS:Mn thin film was made by coevaporation with Electron Beam Evaparation(EBE) method. And structural and optical characteristics of ZnS:Mn thin films were investigated by substrate temperature annealing temperature and dopant Mn. When ZnS:Mn thin film was well deposited with cubic crystalline at substrate temperature of 30$0^{\circ}C$ its surface index was [111] and its lattice constant of a was 5.41$\AA$. Also When ZnA:Mn thin film was well made with hexagonal crystalline at substrate temperature of 30$0^{\circ}C$annealing temperature of 50$0^{\circ}C$and annealing time of 60min its miller indices were (0002) (1011), (1012) and (1120). And its lattice constant of a and c was 3.88$\AA$and 12.41$\AA$ respectively. Finally hexagonal ZnS:Mn thin film with dopant Mn of 0.5wt% had fundamental absorption wavelength of 342nm. And so its energy bandgap was about 3.62eV.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05a
• /
• pp.102-105
• /
• 2004

With varying rapid thermal annealing (RTA) temperature, luminescent properties of ZnMgS:Mn thin film sputter-deposited with one target were measured. Although all samples have the same composition, $Zn_{1-x}Mg_xS:Mn$ (x=0.25) can emit luminescence between 580 and 614 nm, which is controlled by only RTA temperature. It is understood that the energy band gap shift of ZnMgS:Mn thin film phosphor occurs with varying RTA temperature.

• Korean Journal of Materials Research
• /
• v.17 no.9
• /
• pp.475-479
• /
• 2007

Pulsed laser deposition was utilized to grow MnS thin films on c-sapphire substrate using a KrF excimer laser at growth temperatures that ranged from room temperature to $700^{\circ}C$. The results of X-ray diffraction (XRD) and UV-visible spectroscopy were employed to investigate the structural and optical properties of the MnS films. While the growth rate decreased as $T_s$ increased, the overall quality of the film improved. The highest quality MnS film was obtained at $700^{\circ}C$. Variations in the $T_s$ resulted in the MnS films exhibiting different growth mechanisms. The oriented (200) rocksalt MnS film was grown at room temperature. In the case of higher $T_s,\;200{\sim}500^{\circ}C$, the films consisted of mixed phases of rocksalt and wurtzite. The main structure of the films was altered to (111) rocksalt when the temperature was increased to in excess of $600^{\circ}C$. This behavior may very well be the result of elements such as surface energy and atomic arrangement during the growth process. The optical band gap of the obtained ${\alpha}-MnS$ film was estimated to be 3.32 eV.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.6
• /
• pp.13-16
• /
• 2003

Mn-doped $ZnGa_{2}O_{4}$:$Mn^{2+}$ (M=S, Se) thin film phosphors have been grown using a pulsed laser deposition technique under various growth conditions. The structural characterization carr~ed out on a series of $ZnGa_{2}O_{4}$:$Mn^{2+}$ (M=S, Se) films grown on MgO(l00) substrates usmg Zn-rich ceramic targets. Oxygen pressure was varied from 50 to 200 mTorr and Zn/Ga ratio was the function of oxygen pressure. XRD patterns showed that the lattice constants of the $ZnGa_{2}O_{4}$:$Mn^{2+}$ (M=S, Se) thin film decrease with the substitution of sulfur and selenium for the oxygen in the $ZnGa_2O_4$. Measurements of photoluminescence (PL) properties of $ZnGa_{2}O_{4}$:$Mn^{2+}$ (M=S, Se) thin films have indicated that MgO(100) is one of the most promised substrates for the growth of high quality $ZnGa_2O_{4-x}M_{x}$:$Mn^{2+}$ (M=S, Se) thin films. In particular, the incorporation of Sulfur or Selenium into $ZnGa_2O_4$ lattice could induce a remarkable increase in the intensity of PL. The increasing of green emission intensity was observed with $ZnGa_2O_{3.925}Se_{0.075}:$Mn^{2+}$ and $ZnGa_2O_{3.925}S_{0.05}$:$Mn^{2+}$ films, whose brightness was increased by a factor of 3.1 and 1.4 in comparison with that of $ZnGa_{2}O_{4}$:$Mn^{2+}$ films, respectively. These phosphors may promise for application to the flat panel displays.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.9
• /
• pp.89-95
• /
• 1994

BaTiO$_{x}$ thin film as insulator and ZnS:Mn film as phosphour layer for thin film electrouminescent device have been deposited by thermal evalporation and dependence of electrical and opeical characeristics have been studied. The optimum deposition conditions for the BaTiO$_{x}$ thin film are such that BaTiO$_{3}$/TiO$_{2}$ mixing ratio was 0.7, sub strate temperature was 100 $^{\circ}C$ and annealing time was 1 hour at 300 $^{\circ}C$. In this case, the dielectric constant of BaTiO$_{x}$ thin film fabricated under those optimum conditions was 26, and for AnS:Mn thin films, the crystallization was done well and the deposition rate was 1300 $\AA$/min when substrate temperature was 200$^{\circ}C$. Thin film Electroluminescent devices were fabricated using BaTiO$_{x}$ and AnS:Mn thin films. The luminescence threshold voltage of device was 41.5 V and brightness was 1.2${\mu}W/cm^{2}$ at appied voltage of 50 V.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1576-1579
• /
• 2005

With varying rapid thermal annealing (RTA) temperature, luminescence properties of $Zn_{0.75}Mg_{0.25}S:Mn$ thin film deposited by RF-magnetron sputtering technique were investigated. In this study, $Zn_{0.75}Mg_{0.25}S:Mn$ thin film phosphor showed more red emission than those of the previous studies when annealed around 600 or $650^{\circ}C$. Although all samples were deposited from identical source composition, a main peak wavelength of photoluminescence spectra of $Zn_{0.75}Mg_{0.25}S:Mn$ shifted toward shorter wavelengths depending upon increase of RTA temperature. The same dependence of wavelength on RTA temperature was also observed in cathodoluminescence as well as electroluminescence measurements. It was revealed that the change of the luminescence properties were originated from structural changes in $Zn_{0.75}Mg_{0.25}S:Mn$ thin film phosphor from cubic to hexagonal phases analyze using conventional X-ray pole figure mapping. The phase transition would be the origin of luminescence property changes with respect to RTA temperature.

• Korean Journal of Materials Research
• /
• v.28 no.10
• /
• pp.595-600
• /
• 2018

This study investigates the microstructural properties of CoCrFeMnNi high entropy alloy (HEA) oxynitride thin film. The HEA oxynitride thin film is grown by the magnetron sputtering method using nitrogen and oxygen gases. The grown CoCrFeMnNi HEA film shows a microstructure with nanocrystalline regions of 5~20 nm in the amorphous region, which is confirmed by high-resolution transmission electron microscopy (HR-TEM). From the TEM electron diffraction pattern analysis crystal structure is determined to be a face centered cubic (FCC) structure with a lattice constant of 0.491 nm, which is larger than that of CoCrFeMnNi HEA. The HEA oxynitride film shows a single phase in which constituting elements are distributed homogeneously as confirmed by element mapping using a Cs-corrected scanning TEM (STEM). Mechanical properties of the CoCrFeMnNi HEA oxynitride thin film are addressed by a nano indentation method, and a hardness of 8.13 GPa and a Young's modulus of 157.3 GPa are obtained. The observed high hardness value is thought to be the result of hardening due to the nanocrystalline microstructure.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.9
• /
• pp.121-127
• /
• 1994

The capability for application of rf magnetron sputterred and post annealed BaTiO$_{3}$ thin films in dielectrics AC drived TFELD(thin film electroluminescent device) was investigated. The dielectric constant of the thin films slightly increased up to about 25 with increase fothe post annealing temperature in the range of 210$^{\circ}C$-480$^{\circ}C$. The dielectric loss was about 0.005-0.01 except for the high frequency range above 100kHz and nearly independent on post annealing temperature. The BaTiO$_{3}$ thin film used for TFELD was annealed at 480.deg. C and Si$_{3}$N$_{4}$ thin film was inserted between BaTiO$_{3}$, lower dielecrics and ZnS:Mn, phosphor layer for stable driving of the device and for fear of interdiffusion. Regardless of the frequency of the applied sine wave voltage, the threshold voltage of the prepared TFELD was 65volt and saturated brightness was about 3000cd/m$^{2}$ at 130volt(2kHz sine wave), 65volt above V$_{TH}$.

• Electronic Materials Letters
• /
• v.14 no.6
• /
• pp.733-738
• /
• 2018

Undoped and Mn-doped $In_2O_3$ films were prepared by radiofrequency magnetron sputtering technique. The effects of Mn doping on the structural and optical properties of as-prepared films were investigated using X-ray diffraction, X-ray photoelectron spectroscopy and ultraviolet-visible spectroscopy. Mn doping can enhance the intensity of (222) peak in Mn-doped $In_2O_3$ thin film, indicating Mn dopant promotes preferred orientation of crystal growth along (222) plane. XPS analyses revealed that the doped Mn ions exist at + 2 oxidation states, substituting for the $In^{3+}$ sites in the $In_2O_3$ lattice. UV-Vis measurements show that the optical band gap $E_g$ decreases from 3.33 to 2.87 eV with Mn doping in $In_2O_3$, implying an increasing sp-d exchange interaction in the film. Our work demonstrates a practical means to manipulate the band gap energy of $In_2O_3$ thin film via Mn impurity doping, and significantly improves the photoelectrochemical activity.