• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.12
• /
• pp.3899-3908
• /
• 1996

In order to clarify the effects of nonmetallic inclusion contents insteels (SM45C & SCM440) on the tool life, cutting experiment was performed under various cutting conditions. Tool life, cutting force, roughness of machined surface and cutting mechanism are examined on these two kinds of steel. The following conclusions were obtained from the analysis (1) Cutting force of the steels was not affected by chemical component and nonmetallic inclusion. (2) If the rate of amount, Ca/S has a value grater than about 0.2 and addition of less amount of Al, Mn, tool wear of tips decreasesinturning. (3) It is also proved that higher contents of nonmetallic inclusion improve roughness of the surface. (4) Less amount of Ca, higher amount of S, Mn and Al improve the chip breakability.

• Korean Journal of Metals and Materials
• /
• v.49 no.6
• /
• pp.448-453
• /
• 2011

Pre-aging heat treatment after solution heat treatment (SHT) of Al-0.4 wt%Mg-1.2 wt%Si-0.1 wt%Mn alloy sheets for auto-bodies was carried out to investigate the effect of pre-aging and its conditions on the bake-hardening response. Mechanical properties were evaluated by a tensile and Vickers hardness test. Microstructural observation was also performed using a transmission electron microscope (TEM). It was revealed that pre-aging treatments play a great role in the bake-hardening response. In addition, it was found that the sphere-shaped nanosized clusters that can directly transit to the needle-shaped ${\beta}$" phase during the paint-bake process, not being dissolved into the matrix, are formed at 343 K. The result, reveals that the dominant factor of the bake-hardening response is the pre-aging temperature rather than the pre-aging time.

• Ocean and Polar Research
• /
• v.25 no.1
• /
• pp.41-52
• /
• 2003

Sediment trap samples were collected to find out characteristic behaviors of metals in the settling particles by using time-series sediment traps at 678m and 1678m water depths in the Bransfield Strait from December 27th, 1999 to December 26th, 2000. Total mass fluxes at the intermediate water depth (678m water depth) were high in the austral summer and low in the austral winter, whereas at the deep water depth (1678m water depth) they showed high values in both the summer and winter. Total mass fluxes were generally higher in the deep water depth than in the intermediate water depth, which indicates that a substantial amount of sediments are laterally transported by strong currents into the deep basin from the shallow water depths. Aluminium contents also showed large seasonal variations with high values in the winter and low values in the summer. On the contrary, organic carbon contents were high in the summer and low in the winter. Al contents were negatively correlated with organic carbon contents, which may be ascribed that detrital particles are diluted by organic matter produced by phytoplankton in the surface waters. Metals measured in this study exhibited three characteristic behaviors; 1) a positive correlation with Al-Ti, Fe, Mn, V, Co, and Ba, 2) a negative correlation with Al-Cd and Zn, 3) no relationship with Al-Sr, Cu, Cr, Ni. Terrestrial materials may act as a major source fer metals that are positively correlated with Al, and organic matter may be a major source for metals that are negatively correlated with Al. Enrichment factor (EF) of Fe, Mn, Ba, Vi Co, Sr, Cr, and Ni ranged from 0.5 to 1.5, whereas EF of Zn, Cu, and Cd showed much higher values than 1.

• Analytical Science and Technology
• /
• v.8 no.1
• /
• pp.85-90
• /
• 1995

Corrosion characteristics of 4 kinds of the Fe-Al damping alloys has been studied in the 3.5% NaCl solution and compared with a cold rolled mild steel and pure Ti, No passivation, besides Ti, was observed in the Fe-Al damping alloys and a cold rolled mild steel. Corrosion rate was decreased with lower carbon concentration. In the case of Mn addition for improving damping capacity, corrosion rate was decreased in scrap iron but was not decreased in electrolytic iron. It has been shown that corrosion rate of Fe-Al damping alloys lays between that of the pure Ti and that of a cold rolled mild steel.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.74-74
• /
• 2018

Ti-6Al-4V alloys have been widely used as orthopedic materials because of their excellent corrosion resistance and mechanical properties. However, it does not bind directly to the bone, so it requires a surface modification. This problem can be solved by nanotube and micropore formation. Plasma electrolytic oxidation (PEO) treatment for micropore, which combines high-voltage spark and electrochemical oxidation, is a new way of forming a ceramic coating on light metals such as titanium and its alloys. This method has excellent reproducibility and can easily control the shape and size of the Ti alloy. In this study, formation of bioactive surface by PEO-treatment after $2^{nd}$ ATO technique of Ti-6Al-4V alloy was invesgated by various instrument. Nanotube oxide surface structure was formed on the surface by anodic oxidation treatment in 0.8 wt.% NaF and 1M $H_3PO_4$ electrolytes. After nanotube formation, nanotube layer was removed by ultrasonic cleaning. PEO-treatment was carried out at 280V for 3 minutes in the electrolytic solution containing the bioactive substance (Mg, Zn, Mn, Sr, and Si). The surface of Ti-6Al-4V alloy was observed by field emission scanning electron microscopy (FE-SEM, S-4800 Hitachi, Japan). An energy dispersive X-ray spectrometer (EDS, Inca program, Oxford, UK) was used to analyze the spectra of physiologically active Si, Mn, Mg, Zn, and Sr ions. The PEO film formed on the Ti-6Al-4V alloy surface was characterized using an X-ray diffractometer (TF-XRD, X'pert Philips, Netherlands). It is confirmed that bioactive ions play an essential role in the normal bone growth and metabolism of the human skeletal tissues.

• Journal of the Mineralogical Society of Korea
• /
• v.17 no.4
• /
• pp.357-364
• /
• 2004

Mineral chemistry of talc from the Dongyang talc deposits was studied to characterize the differences between dolomite-origin talc (talc I) and tremolite-origin talc (talc II). Average iron and aluminum contents are higher in talc II, 2.18 wt% FeO and 0.31 wt% $Al_2$O$_3$), than in talc I, 1.48 wt% FeO and 0.08 wt% $Al_2$O$_3$). Consistently lower Mg/(Mg+Fe+Mn) ratios and higher AI concentrations with uniform values of talc II compared to talc I seem to reflect the compositional differences of the original materials, tremolite and dolomite, respectively. Relative enrichment of Al as well as Fe in talc II compared to tremolite can be attributed to their immobile behaviors during alteration process and the rapid diffusion of hydrothermal fluids, which can accelerate instantaneous nucleation with immaturity growth of talc II. Increase in the concentrations of talc II can lower the ore grade by increasing concentrations of impure components such as AI and Fe, and by abundant presence of tremolite as well.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.3
• /
• pp.149-154
• /
• 2012

According to the coagulation tests for PACs with various basicities, the PACB with lower basicity showed higher coagulation efficiencies of organics and phosphorus than the PAC with higher basicity. The PACB contained higher amount of monomeric Al (III) hydrolytic species comparing with PAC. In case of the coagulation for the sewage treated water, the coagulation efficiency by the charge neutralization and sweep floc formation was higher with PACB than with PAC. Accordingly, when $Al_2O_3$ concentration was similar in the coagulant, PACB showed higher removal efficiencies of turbidity, $COD_{Mn}$, TP, and $PO_4$-P comparing with PAC, especially in the lower range of coagulant dose.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2000.11a
• /
• pp.421-422
• /
• 2000

VOCs 처리기술로는 촉매연소, 열적처리, 생물학적처리법 등이 있으며, 촉매연소방법의 경우 저온에서 처리가 가능하여 처리비용 절감 등의 효과를 고려할 때 가장 경제적인 방법으로 평가되고 있다(Guisnet, et al., 1999). VOCs 처리에는 대부분 고가의 귀금속촉매를 많이 사용하므로, 경제적 부담을 줄이기 위하여 귀금속을 담체(SiO$_2$, A1$_2$O$_3$, TiO$_2$등)에 담지시켜 활용하거나, 귀금속촉매를 대체하기 위한 Mn, Co, Cu 등의 금속 산화물 촉매에 대한 연구가 활발히 진행되고 있다. (중략)

• Korean Journal of Mineralogy and Petrology
• /
• v.35 no.2
• /
• pp.125-140
• /
• 2022

The Xiquegou Pb-Zn deposit is located at the Qingchengzi orefield which is one of the largest Pb-Zn mineralized zone in the northeast of China. The geology of this deposit consists of Archean granulite, Paleoproterozoinc migmatitic granite, Paleo-Mesoproterozoic sodic granite, Paleoproterozoic Liaohe group, Mesozoic diorite and Mesozoic monzoritic granite. The Xiquegou deposit which is a Triassic magma-hydrothermal type deposit occurs as vein ore filled fractures along fault zone in unit 3 (dolomitic marble and schist) of Dashiqiao formation of the Paleoproterozoic Liaohe group. Xiquegou Pb-Zn deposit consists of quartz, apatite, calcite, pyrite, arsenopyrite, pyrrhotite, marcasite, sphalerite, chalcopyrite, stannite, galena, tetrahedrite, electrum, argentite, native silver and pyrargyrite. Wallrock alteration of this deposit contains silicification, pyritization, dolomitization, chloritization and sericitization. Based on mineral petrography and paragenesis, dolomites from this deposit are classified two type (1. dolomite (D₀) as wallrock, 2. dolomite (D₁) as wallrock alteration in Pb-Zn mineralization quartz vein ore). The structural formulars of dolomites are determined to be Ca_1.03-1.01Mg_0.95-0.83Fe_0.12-0.02Mn_0.02-0.00(CO₃)₂(D₀) and Ca_1.16-1.00Mg_0.79-0.44Fe_0.53-0.13Mn_0.03-0.00As_0.01-0.00(CO₃)₂(D₁), respectively. It means that dolomites from the Xiquegou deposit have higher content of trace elements compared to the theoretical composition of dolomite. The dolomite (D₁) from quartz vein ore has higher content of these trace elements (FeO, PbO, Sb₂O₅ and As₂O₅) than dolomite (D₀) from wallrock. Dolomites correspond to Ferroan dolomite (D₀), and ankerite and Ferroan dolomite (D₁), respectively. The structural formular of chlorite from quartz vein ore is (Mg_1.65-1.08Fe_2.94-2.50Mn_0.01-0.00Zn_0.01-0.00Ni_0.01-0.00Cr_0.02-0.00V_0.01-0.00Hf_0.01-0.00Pb_0.01-0.00Cu_0.01-0.00As_0.03-0.00Ca_0.02-0.01Al_1.68-1.61)_5.77-5.73(Si_2.84-2.76Al_1.24-1.16)_4.00O₁₀(OH)₈. It indicated that chlorite of quartz vein ore is similar with theoretical chlorite and corresponds to Fe-rich chlorite. Compositional variations in chlorite from quartz vein ore are caused by mainly octahedral Fe²⁺ <-> Mg²⁺ (Mn²⁺) substitution and partly phengitic or Tschermark substitution (Al^3+,VI+Al^3+,IV <-> (Fe²⁺ 또는 Mg²⁺)^VI+(Si⁴⁺)^IV).

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.717-721
• /
• 2012

Manganese dioxide ($MnO_2$) is one of the most important cathode materials used in both aqueous and non-aqueous batteries. The $MnO_2$ polymorph that is used for lithium primary batteries is synthesized either by electrolytic (EMD-$MnO_2$) or chemical methods (CMD-$MnO_2$). Commonly, electrolytic manganese dioxide (EMD) is used as a cathode mixture material for dry-cell batteries, such as a alkaline batteries, zinc-carbon batteries, rechargeable alkaline batteries, etc. The characteristics of lithium/manganese-dioxide primary cells fabricated with EMD-$MnO_2$ powders as cathode were compared as a function of the parameters of a manufacturing process. The flexible primary cells were prepared with EMD-$MnO_2$, active carbon, and poly vinylidene fluoride (PVDF) binder (10 wt.%) coated on an Al foil substrate. A cathode sheet with micro-porous showed a higher discharge capacity than a cathode sheet compacted by a press process. As the amount of EMD-$MnO_2$ increased, the electrical conductivity decreased and the electrical capacity increased. The cell subjected to heat-treatment at $200^{\circ}C$ for 1 hr showed a high discharge capacity. The flexible primary cell made using the optimum conditions showed a capacity and an average voltage of 220 mAh/g and 2.8 V, respectively, at $437.5{\mu}A$.