• 한국분말재료학회지
• /
• 제23권5호
• /
• pp.397-401
• /
• 2016

A lean alloy is defined as a low alloy steel with a minimum amount of the alloying element that maintains the characteristics of the sintered alloy. It is well known that the addition of elements such as Cr, P, Si, or Mn improves the mechanical characteristics of the alloy, but decreases the sinterability. The mother alloy is used to avoid an oxidation reaction with the alloying elements of Cr, P, Si or Mn. The purpose of this study is to determine the change in the mechanical properties of Fe-P-Mo and Fe-P-Mn alloys as a result of the addition of Si. In this article, the Fe-P-Mo and Fe-P-Mn alloys to which Si is added are compacted at $7.0g/cm^3$ and then sintered in $H_2-N_2$ at $1120^{\circ}C$. The P around the macropores and large grains reduces due to the formation of $SiO_2$ as the Si content increases. This is caused by the increase in strength owing to reducing intergranular fracture by suppressing the reaction with oxygen.

• 한국세라믹학회지
• /
• 제56권4호
• /
• pp.412-420
• /
• 2019

In this study, the dielectric and polarization properties of manganese (Mn% = 0.0, 0.1, 0.2, 0.5) doped (Pb_0.93La_0.07)(Zr_0.82Ti_0.18)O₃ (PLZT 7/82/18) anti-ferroelectric ceramics were studied for energy storage capacitor and pyroelectric applications. A systematic investigation demonstrated that the electric properties of PLZT 7/82/18 ceramics are affected significantly by the Mn-doping content. A maximum dielectric constant of ~ 2,128 at 1 kHz was found for 0.1% Mn-doped PLZT ceramics with a low dielectric loss of 0.018. The bipolar polarization versus electric field (P-E) hysteresis loops were traced for all compositions showing a typical anti-ferroelectric nature. The breakdown field was found to decrease with Mn-doping. The energy storage density and efficiency were found to be 460 J/㎤ and ~ 63%, respectively, for 0.2% Mn-doped PLZT ceramics. The pyroelectric coefficient of PLZT ceramics shows an increase based on the amount of Mn-doping.

• 소성∙가공
• /
• 제17권4호
• /
• pp.240-248
• /
• 2008

The effect of alloying elements(Mn, S, Mo, B) on the high temperature deformation behavior of Fe-29%Ni-17%Co (Kovar) alloy were investigated. And the effect of high temperature oxidation on the hot ductility was also studied. The hot ductility of Kovar alloy was drastically increased with the addition of Mn and lowering of S content. It has been found that the brittle intergranular fracture at high temperature cracking is closely associated with the FeS sulfide along the grain boundary. When Mn was added, the type of sulfide was changed to MnS from FeS and ductile intergranular fracture and transgranular fracture were promoted. The formation of oxide layer was found to have minimized the hot ductility of the Kovar alloy significantly. Grain boundary micro-cracks in the internal oxide region were noted following deformation due to high temperature, one of which acting as a notch that caused the poor hot workability of the oxidized specimen. The addition of Mo to the Kovar alloy could also retard the decrease in the hot ductility of the oxidized specimen through the prevention of notching due to internal oxidation. Hot ductility was remarkably improved by the addition of Boron. The improvement of hot ductility results from the grain boundary migration mainly due to the dynamic recrystallization at lower temperature range ($900{\sim}1000^{\circ}C$).

• 한국식품과학회지
• /
• 제44권4호
• /
• pp.484-487
• /
• 2012

에너지 분산형 X-선 형광분석기를 이용하여 국산과 수입산 황금의 원산지 판별 기술을 개발하였다. P, S, Cl, K, Ca, Mn, Fe, Cu, Zn 등 총 43종의 무기성분 함량을 총 206개의 시료에서 측정하였다. 특히 국산과 수입산 시료 간에 함량비 차이가 크게 나타난 무기원소는 P, S, K, Ca, Cl, Mn, Fe 등 이었다. 다량원소에서 P의 경우 국산은 0.38%이고 중국산은 0.23%이었고, S은 국산이 0.16%이고 중국산이 0.25%였으며, K은 국산은 1.58%이고 중국산은 1.20%, Ca은 국산은 0.18%, 중국산이 0.39%로 나타나 큰 차이를 보여주었다. 미량원소에서도 Cl의 경우 국산은 487.72 ppm이고 중국산은 616.69 ppm이었고, Mn은 국산이 39.79 ppm이고 중국산이 7.92 ppm, Fe은 국산은 122.79 ppm이고 중국산은 274.87 ppm으로 나타나 국산과 중국산 황금의 미량원소 함량비 차이를보여주었다. Spectra EDX의 반정량법인 standardless fundamental prameters (SLFP)방법을 이용하여 원소별 상대적 함량 백분비를 얻은 다음, 다변량 분석 중의 한 방법인 정준판별분석법으로 분석하여 원산지를 판별하였다. 국산 시료 108점 중 8점을 중국산으로 판별하였고, 중국산 98점 중 2점을 국산으로 판별하여 95.15%의 판별정확도를 나타냈고 상관계수는 0.888이었다. 에너지 분산형 X-선 형광분석기에 의한 원산지 판별 기술이 황금의 원산지 판별에 유용하게 사용될 수 있다고 판단된다.

• 한국주조공학회지
• /
• 제3권3호
• /
• pp.174-180
• /
• 1983

The matrix changes and graphite formation in high manganese cast iron (Fe-12Mn-3.5C) are studied with increasing nickel and silicon content. Also, the decomposition of carbides and graphite precipitation are studied by adequate heat treatment.The results obtained in this work are as follows. 1. In high manganese cast iron, fine flakes graphite appeared by adding 5 wt% nickel and A-type flakes graphite can be obtained by adding 7 wt% nickel. 2. Nodular graphite are obtained by graphite spheroidizing treatment with same melt. 3. In high manganese cast iron containing 7 wt% nickel, full austenitic matrix with nodular graphite can be achieved by water quenching after 10 hours' solution heat treatment at $1050^{\circ}C$ in case of containing 2.0 wt% silicon, and 6 hours' at the same temperature in case of containing 2.5 wt% silicon.

• Journal of Nutrition and Health
• /
• 제30권9호
• /
• pp.1045-1049
• /
• 1997

In order to study the content of selected elements in the organs of the mice, mice were fed with green juice of Angelica keiskei Koidz for 16 weeks. The results obtained from the experiments are summarized as follows : 1) The element contents(cr, Mn, Ni, Cu, Zn, Cd, Ba, Pb, and Fe) in the whole plant are generally the same as those the previous reports. 2) The element contents(Cr , Mn, Ni, Cu, Zn, Cd, Ba, Pb and Fe) in the green juice did not exceed those of the edible water standard. 3) The element contents (Cr, Mn, Ni, Cu, Zn, Cd, Ba, Pb and Fe) in the brain is slightly higher than those in the whole plants. 4) The element contents(Cr, Ni, Pb and Fe) in the organs of the mice fed green juice for 16 weeks are the same as those of the previous reports.

• 한국세라믹학회지
• /
• 제38권6호
• /
• pp.506-508
• /
• 2001

The ferrite plating with applying power ultrasound waves of 19.5 kHz and 600W enabled us to encapsulate entirely MnZn ferrite cores for transformers with Ni$\sub$x/Zn$\sub$y/Fe$\sub$3-x-y/O$_4$coating. Supplying a NH$_4$OH solution during the plating broke the limit of the solubility of Ni ions to ferrite-plated films. The electrical resistivity of the NiZn ferrite coating increased with increasing the Ni and Zn content, reaching 2.3${\times}$10$\^$5/Ωcm at the composition of Ni$\sub$0.24/Zn$\sub$0.30/Fe$\sub$2.46/O$_4$. The saturation magnetization was 540 emu/㎤. As a result, the MnZn ferrite cores were successfully encapsulated with the NiZn ferrite coatings for an insulation layer.

• 한국군사과학기술학회지
• /
• 제7권1호
• /
• pp.47-58
• /
• 2004

Loss factors of A356, Mn-Cu alloy and aluminum matrix composites reinforced with $SiC_p$ and Ni-coated graphite particles at various contents have been investigated using clamped-free cantilever beam method. The loss factors of half-power bandwidth of the specimens were measured over a wide range of frequencies from 50 to 3300Hz. Among the specimens, Al-10%$SiC_p$-10%$C_p$ showed the highest loss factor at the mode I, while Mn-Cu alloy showed the highest loss factors at the modes II and III. Consequently, at the mode I the Al-10%$SiC_p$--10%$C_p$ showed the loss factor of 0.00093, which is 2.64 and 1.58 times higher than those of A356 and Mn-Cu alloy, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.260-264
• /
• 1999

In this paper, the structural, dielectrial and piezoelectrical properties of 0.03Pb(Sb$\sub$1/2/Ti$\sub$0.495/)O$_3$+Xwt% MnO(x= 0, 0.3, 0.4, 0.5, 0.7) system ceramics were investigated as a function of the addition of MnO. As a result, the samples of 0.3wt% MnO content showed the highest mechanical quality factor(Qm) of 1487, and its dielectric constant and electro mechanical coupling factor(Kp) 1357, 54.3%, respectively. Therefore, the dielectrial and piezoelectrical properties of the composition ceramics were indicated as the materials suitable for piezoelectric transformer.

• 한국광물학회지
• /
• 제23권4호
• /
• pp.281-295
• /
• 2010

비오염토양, 폐광산 주변토양, 산업단지 주변토양을 채취하여 X-선 회절분석, pH, 전기전도도, 양이온교환능력, 작열감량, 산화철 산화망간 함량, 중금속 함량 및 중금속 존재형태와 토양대자율의 상관관계를 파악하였다. 시료의 X-선회절분석 정량분석결과 비오염지역 토양에서는 모암에 따라 다양한 광물이 분포하고 있지만, 적철석과 자철석은 거의 관찰되지 않았다. 폐광산 주변토양은 폐광석, 광물찌꺼기 등의 영향으로 적철석이 많이 확인되었고, 일부 시료에서는 자철석도 존재하였다. 산업단지 주변시료에서는 방해석과 철백운석 등의 탄산염 광물들이 대부분의 시료에서 확인되었다. 중금속의 존재형태를 파악하기 위한 연속추출 실험 결과, 폐광산 주변지역 토양시료에서 철, 망간, 중금속 원소들은 reducible, oxidizable, residual 단계별 추출 형태로 80% 이상, 산업단지 주변시료에서는 50% 이상 존재하였다. 산업단지 주변시료의 경우, 탄산염 광물의 영향으로 carbonate 형태가 높게 나타났다. 왕수로 추출된 철, 망간, 비소, 아연 함량은 산화철/산화망간 형태를 지시하는 dithionite-citrate-bicarbonate (DCB) 용출 함량과 매우 밀접한 정의 상관관계를 보여주었다. 철과 비소는 각각 왕수추출함량의 54%, 58%가 산화철/산화망간 형태과 함께 거동하는 것으로 나타났다. 대자율은 $0.005{\sim}2.131{\times}10^{-6}m^3kg^{-1}$의 범위로서, 시료 내에 적철석, 자철석 등 산화철 광물이 존재할 경우 대자율이 높게 측정되었다. 토양 내 중금속 함량과 대자율의 상관관계를 살펴본 결과 철 (r=0.608, p<0.01), 망간(r=0.615, p<0.01)과 유의한 정의 상관관계를 보였으며, 카드뮴(r=0.544, p<0.05), 크롬(r=0.714, p<0.01), 니켈(r=0.645, p<0.05), 납(r=0.703, p<0.01), 아연(r=0.496, p<0.01) 등의 중금속 원소와도 유의한 정의 상관관계를 보였다. 철, 망간 및 중금속원소들 간의 상관관계를 살펴본 결과, 왕수로 용출된 철, 망간 함량과 카드뮴, 크롬, 구리, 니켈, 아연 등의 중금속 함량이 정의 상관관계를 보이고 있다. 또한 산화철 및 산화망간 함량은 비소 및 니켈 함량과 밀접한 상관성이 있는 것으로 나타났다. 이는 비소와 니켈은 산화철 산화망간에 흡착되어 함께 거동함을 암시한다.