• Korean Journal of Environmental Agriculture
• /
• v.20 no.5
• /
• pp.346-351
• /
• 2001

Oxidation of Cr(III) to Cr(VI) can increase availability and toxicity of chromium. In this study, possible mechanisms by which pH and organic matter can control the chromium oxidation and reduction in soil system were examined using four soils of different pHs and organic matter contents. Reduction of Mn-oxides occurred in the soils of higher organic matter content (4.0%), but Mn-oxide was quite stable during the incubation in the soil of pH 7.0 and 0.5% organic matter content. Manganese oxides can be reductively dissolved at lower pH and higher organic matter conditions. The soil of pH 7.0 and 4.0% organic matter content showed the highest Cr-oxidation potential. Reduction of soluble Cr(VI) was observed in all the soils examined. The most rapid reduction was found in soil of pH 5.5 and 4.0% organic matter content, but the reduction was slow in soil of pH 7.0 and 0.5% organic matter content. Thus, the reductive capacity of organic matter added soils was much higher as compared to other two soils of lower organic matter content. In all the soils examined, the reductive capacity of soluble chromium was much higher than the oxidative capacity. Organic matter was found to be the most important controlling factor in the chromium oxidation and reduction. Reduction of Cr(VI) to Cr(III) could be a potentially useful remediation or detoxification process, and availability and toxicity of chromium in soil would be controlled by controlling organic matter content and pH of the soils.

• Journal of the Korean Ceramic Society
• /
• v.16 no.1
• /
• pp.3-12
• /
• 1979

The effects of sintering temperature and sintering atmosphere on magnetic properties and microstructuresof Mn-Zn ferrites have been studied. Mixture of 52.8mole% $Fe_2O_3$, 26.4mole% MnO, 15.1mole0% ZnO and 5.7mole% NiO was prepared, and 0.1mole% CaO, 0.02mole% $SiO_2$ were added as minor additives. After calcining and ball milling the powder was granulated for compacting. The specimens were sintered at $1, 250^{\circ}$, $1, 300^{\circ}$and 1, 35$0^{\circ}C$ in the various atmosphere of $N_2$, $N^_2\DIV0.6% O_2$, $N_2＋2.7% O_2$, $N_2＋4.1% O_2$, $N^2＋8.2% O_2$ and air for 3 hours and cooled in $N_2$ atmosphere. The grian growth rate and densities increase as sintering temperature and oxygen content of atmosphere increase. At the sintering temperature of $1, 250^{\circ}C$ the initial permeabilities increase as oxygen content of atmosphere increase. At the sintering temperature of$ 1, 300^{\circ}$and $1, 350^{\circ}$ the initial permeabilities show maximum values at $N_2＋4.1% O_2$ atmosphere. The secondary peaks of initial permeabilities are observed between 100$^{\circ}$and 20$0^{\circ}C$, and the positions of secondary peaks move to higher temperature as oxygen content of atmosphere increases. Q-factors decrease as sintering temperature increases and oxygen content of atmosphere decreases.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.16 no.2
• /
• pp.105-109
• /
• 1987

The mineral content of Dolowe, which were prepared in the laboratory and marketed Korean products of Dolwoe, Japanese product of Dolwoe and Korean-roasted products of Dolwoe were analysed and compared. Dolwoe-leaf tea had high mineral content of Ca, Mg, Mn and Cu, while Dolwone-stem tea had high mineral content of K, Na and Fe. Especially in the ash of Dolwoe-stem tea showed the highest mineral content of K (33.4%) Dolwoe teas were extracted for 5 minutes as ratio of $1,000m{\ell}$ boiling water to 4g Dolwoe tea (250: 1, v/w). Comparing the ratio of extraction of minerals in Dolwoe tea made by us and marketed Dolwoe products, K was the most abundant element of all extractions with the rate of $83.2%{\sim}96.3%$ followed by Mg with $44.8%{\sim}62.2%$, Ca with $23.1%{\sim}64.4%$ and Na with $6.3%{\sim}55.6%$. On the other hand Mn, Fe and Cu were extracted in extremely small quantities.

• Journal of Korea Foundry Society
• /
• v.33 no.4
• /
• pp.162-170
• /
• 2013

The effects of Mn content and cooling rate on the eutectic reaction of flake graphite cast irons were studied by a combined analysis of macro/micro-structure and cooling curve data. The correlation between the eutectic reaction parameter and macro/microstructure was systematically investigated. Two sets of chemical compositions with different Mn contents were designed to cast. Three types of molds for cylindrical specimens with different diameters were prepared to analyze the cooling rate effect. The difference between undercooling temperature and cementite eutectic temperature (${\Delta}T_1=T_U-T_{E,C}$), which is decreased by increasing the Mn content or increasing the cooling rate, is considered to be a suitable eutectic reaction parameter for predicting graphite morphology. According to the criterion, A-type graphite is mainly suggested to form for ${\Delta}T_1$ over $20^{\circ}C$, and D-type graphite is mainly suggested to form for ${\Delta}T_1$ below $0^{\circ}C$. Eutectic reaction time (${\Delta}T$), which is increased by increasing the Mn content and decreased by increasing the cooling rate, is regarded as a suitable eutectic reaction parameter for predicting eutectic cell size. Eutectic cell size is found to decrease in proportion to the decrease of ${\Delta}T$.

• Journal of Korea Foundry Society
• /
• v.29 no.1
• /
• pp.27-32
• /
• 2009

The microstructure of Al-7Si-0.4Mg-1Fe alloy mainly consists of aluminum dendrites, Al-Si eutectics, and $Al_5FeSi$ needles. When Mn was added to the alloy, the substantial amount of $Al_5FeSi$ phase was changed into Al(Mn,Fe)Si, however the needle-like morphology was almost unchanged. Combined additions of Cr or Sr with Mn to the base alloy resulted in rod-like Al(Mn, Fe,Si)Si phase. The tensile properties of as-cast alloys were enhanced by the Mn addition, especially when it was added with Sr. The tensile properties after T6 heat treatment was a little improved with 0.7%Mn addition, but Cr or Sr additions with Mn didn't show any positive effect on the properties of heat-treated alloys.

• Journal of Magnetics
• /
• v.20 no.4
• /
• pp.336-341
• /
• 2015

MnBi alloys were fabricated by arc melting and annealing at 573 K. The heat treatment enhanced the content of the low-temperature phase (LTP) of MnBi up to 83 wt%. The Bi-excess assisted LTP MnBi alloys were used in the hybridization with the Nd-Fe-B commercial Magnequench ribbons to form the hybrid magnets (100-x)NdFeB/xMnBi, x = 20, 30, 40, 50, and 80 wt%. The as-milled powder mixtures of Nd-Fe-B and MnBi were aligned in a magnetic field of 18 kOe and warm-compacted to anisotropic and dense bulk magnets at 573 K by 2,000 psi for 10 min. The magnetic ordering of two hard phase components strengthened by the exchange coupling enhanced the Curie temperature ($T_c$) of the magnet in comparison to that of the powder mixture sample. The prepared hybrid magnets were highly anisotropic with the ratio $M_r/M_s$ > 0.8. The exchange coupling was high, and the coercivity $_iH_c$ of the magnets was ~11-13 kOe. The maximum value of the energy product $(BH)_{max}$ was 8.4 MGOe for the magnet with x = 30%. The preparation of MnBi alloys and hybrid magnets are discussed in details.

• Korean Journal of Materials Research
• /
• v.27 no.12
• /
• pp.643-651
• /
• 2017

Four types of high Mn TWIP(Twinning Induced Plasticity) steels were fabricated by varying the Mn and Al content, and the tensile properties were measured at various strain rates and temperatures. An examination of the tensile properties at room temperature revealed an increase in strength with increasing strain rate because mobile dislocations interacted rapidly with the dislocations in localized regions, whereas elongation and the number of serrations decreased. The strength decreased with increasing temperature, whereas the elongation increased. A martensitic transformation occurred in the 18Mn, 22Mn and 18Mn1.6Al steels tested at $-196^{\circ}C$ due to a decrease in the stacking fault energies with decreasing temperature. An examination of the tensile properties at $-196^{\circ}C$ showed that the strength of the non-Al added high Mn TWIP steels was high, whereas the elongation was low because of the martensitic transformation and brittle fracture mode. Although a martensitic transformation did not occur in the 18Mn1.9Al steel, the strength increased with decreasing temperature because many twins formed in the early stages of the tensile test and interacted rapidly with the dislocations.

• Journal of the Korean Ceramic Society
• /
• v.34 no.4
• /
• pp.351-356
• /
• 1997

The origin of the variation of initial permeability in manganese-zinc ferrite polycrystals with a content of hematite was investigated. Initial permeability showed maximum with hematite content while there was no significant change in microstructure. Saturation magnetization increased with hematite content. So the variation of initial permeability was not explained on the basis of microstructural change or saturation magnetization. Temperature dependence of initial permeability revealed magnetocrystalline anisotropy was the origin of the variation of initial permeability. The change in magnetocrystalline anisotropy was ascribed to the variation in ferrous ion concentration. Therefore the variation of initial permeability in manganese-zinc ferrite polycrystals with a content of hematite was due to ferrous ion concentration via magnetocrystalline anisotropy.

• Journal of the Korean Ceramic Society
• /
• v.24 no.5
• /
• pp.461-469
• /
• 1987

Single crystals of Mn-Zn Ferrite were grown by slow cooling method using Na2B4O7 as flux agent. The effects of flux content and cooling rate on the types of crystals, and the relation between supersaturation and growth mechanism were studied. As a result, the types of grown crystals occurred as plate, hopper and octahedral crystals. The occurrence of these crystal types was dependent on flux content. The habit was found to correlate with the growth rate and supersaturation. The lateral growth of a dendritic crystal is related to the twin layer. The growth of crystals from borax melts mainly occurred by the layer-spreading growth following corner and edge nucleation caused by high supersaturation in the melt. Especially, the plate crystals were produced on top of the melts. The hopper and octahedral crystals occurred at lower supersaturation than the plate crystals.

• Journal of Korea Foundry Society
• /
• v.12 no.2
• /
• pp.139-148
• /
• 1992

The mechanical properties of Ti-Al intermetallic compounds which contain Mn, Zr, or Cr as the third element have been evaluated by means of hardness and compression tests. Microstructures have also been examined using an optical microscope. The cast structures of Ti-Al alloys are coarsened and the lamellar volume fraction is increased by the additions of Mn or V, but the cast structures are refined by the addition of Zr. Hardness tests of room temperature and compression tests at $600^{\circ}C$ showed that the mechanical properties of Ti-Al alloys were mainly dependent on the volume fraction of the ${\alpha}_2$ phase, grain size and solid solution hardening. However according to the compression test at $1000^{\circ}C$, the yield strength of Ti-Al alloys decreased with an increase in Mn or Cr content, but increased with an increase in the Zr content.