• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.4
• /
• pp.533-540
• /
• 2006

In this study, the possibility of green tea waste (GTW) as a new ingredient of byproducts-mixed silage was investigated. Characteristics of GTW were low in dry matter (DM) content (20%), and high in crude protein (30 to 36%) and tannins (8.5%). The GTW was added to mixed silages composed of tofu cake, rice straw and rice bran that are locally available in Japan. In experiment 1, the effect of GTW addition to silage made from various patterns of byproducts mixture based on tofu cake was studied. In experiment 2, the effect of GTW addition and storage temperature on fermentation characteristics, nutrient contents and in vitro ruminal gas production of byproducts-mixed silages were examined. In experiment 1, GTW addition on tofu cake accelerated acetic, propionic and butyric acid accumulation in the silage. When rice straw was mixed with tofu cake, DM content was increased from 47 to 56%, lactic acid was the main acid and the pH was decreased below 4.2. In this case, GTW addition to those mixtures did not affect acid concentrations of the silage. In experiment 2, GTW addition to the byproducts mixture increased lactic acid concentration, decreased the pH and DM loss of the silages. In GTW treatments, tannin concentration was lower in the silage stored at $30^{\circ}C$ than $15^{\circ}C$. Addition of GTW into the silage also increased in vitro ruminal gas production. It was concluded that addition of GTW into byproducts-mixed silage enhanced lactic acid fermentation when there were insufficient materials for lactic acid production. Utilization of GTW as an ingredient in mixed silages would be effective in enhancing fermentation characteristics, lowering tannin content and in vitro ruminal gas production.

• Journal of environmental and Sanitary engineering
• /
• v.15 no.2
• /
• pp.34-40
• /
• 2000

In the tungsten industry, molybdenum wire which used as the center supporter for coil shape tungsten wire was removed. Nitric acid dissolution method which used prevalently up to the present, takes nitric acid as major component and use noxious material such as sulfuric acid and hydrochloric acid remove molybdenum wire which used as center supporter by dissolve selectively within the range of no damage on tungsten wire. Mixed acid waste water occurred to the process were difficult to be decomposed by the conventional methords. This mixed acid waste water was treated by ozone, and It was obtained using possible by-product through the treatment waste water. For the three reactors with the same volume ; Blank reactor, Disturbance plate reactor, Packed-bed reactor ; the results were as follows : For the blank reactor COD removal efficiency in the pH = 4 (HRT : 6hr) was 28.5%, COD removal efficiency in the pH = 7 (HRT : 6hr) was 28.6%, and COD removal efficiency in the pH = 10 (HRT : 6hr) was 27.8%. For the disturbance plate reactor COD removal efficiency in the pH = 4 (HRT : 6Min.) was 86.5%, COD removal efficiency in the pH =7 (HRT : 6Min.) was 84.4%, and COD removal efficiency in the pH = 10 (HRT : 60Min.) was 86.8%. For the packed-bed reactor COD removal efficiency in the pH = 4 (HRT : 40Min.) was 76.0%, COD removal efficiency in the pH = 7 (HRT : 40Min.) was 81.3%, and COD removal efficiency in the pH = 10 (HRT : 40Min.) was 84.6%. After O3 treatment using possible by-product(Na2SO4) was 150g/ℓ.

• Clean Technology
• /
• v.14 no.2
• /
• pp.123-128
• /
• 2008

The waste solution, which was discharged from the recovery process of LCD etching solution, consists of 15 wt% nitric acid and 20 wt% acetic acid. In this study, it was conducted to separate acid individually from the mixed acid by vacuum evaporation under -760 mmHg gauge and at $40^{\circ}C$. We have investigated evaporation behavior of acid as a function of temperature. There have been problems that tiny amount of nitric acid were evaporated simultaneously above $33^{\circ}C$. Thus, efforts were conducted to recover acetic acid by vacuum evaporation with adding $H_2O$, waste mixed acid and 20 g/L NaOH for a curb on evaporation of nitric acid. By adding $H_2O$, evaporation of nitric acid was reduced from 7% to 0.78%. However, it was reduced from 7% to 0.25% by adding mixed acid. In view of the results achieved so far, we may expect to separate the etching solution individually by controlling vacuum conditions.

• Advances in environmental research
• /
• v.5 no.1
• /
• pp.19-35
• /
• 2016

The phytoextraction of some toxic heavy metals from municipal waste dump soil by castor plant (Ricinus communis) was tested under natural and single or mixed chelant-assisted scenarios in pot microcosms. A sandy loam with total metal contents (mg/kg): Cd (84.5), Cu (114.5), Ni (70.3), Pb (57.8), and Zn (117.5), was sampled from an active dumpsite in Calabar, Nigeria and used for the study. Castor (small seed variety) was grown under natural phytoextraction or single/binary chelant (citric acid, oxalic acid, and EDTA) applications (5-20 mmol/kg soil) for 63 days. Castor exhibited no visual phytotoxic symptoms with typically sigmoid growth profiles at the applied chelant doses. Growth rates, however, decelerated with increase in chelant dose. Post-harvest biomass yields were higher under chelant application than for natural phytoextraction. Both root and shoot metal concentrations (mg/kg) increased quasilinearly and significantly ($p{\leq}0.05$) with increase in chelant dose, furnishing maximum levels as: Cd (55.6 and 20.9), Cu (89.5 and 58.4), Ni (49.8 and 19.6), Pb (32.1 and 12.1), and Zn (99.5 and 46.6). Ranges of translocation factors, root and shoot bioaccumulation factors were 0.21-3.49, 0.01-0.89 and 0.01-0.51, respectively. Overall, the binary chelant treatments were less toxic for R. communis growth and enhanced metal accumulation in shoots to a greater extent than the single chelant scenarios, but more so when EDTA was present in the binary combination. This suggests that the mixed chelants could be considered as alternative treatments for enhanced phytoextraction and revegetation of degraded waste dump soils.

• Journal of Environmental Science International
• /
• v.15 no.9
• /
• pp.897-905
• /
• 2006

This study has been conducted to investigate biodegradation characteristics and optimum mixing ratio for co-digestion with thermophilic acid-fermented food waste and sewage sludge using batch anaerobic digester. As the basis operating conditions for anaerobic digestion, the reaction temperature was controlled $35{\pm}1^{\circ}C$ and stirrer was set 70rpm. Thermophilic acid-fermented food waste and sewage sludge were mixed at the ratio of 10:0, 7:3, 5:5, 3:7, 0:10 and 5;5(food waste : sewage sludge) as the influent substrates. In results of co-digestion according to mixing ratio of thermophilic fermented food wastes and sewage sludge in batch mesophilic anaerobic digestion reactor, $385mL\;CH_4/g\;VS_{added}$ of methane production rate at 1:1 mixing ratio was more than that of any other mixing ratios. Compared with $293mL\;CH_4/g\;VS_{added}$ of methane production rate at 1:1 mixing ratio of food wastes and sewage sludge, pretreatment of food wastes by thermophilic acid fermentation was more effective in co-digestion with sewage sludge.

• Resources Recycling
• /
• v.18 no.4
• /
• pp.62-69
• /
• 2009

We researched separation of mixed waste acids with HF, $CH_3COOH$, $HNO_3$ that were produced during a semiconductor wafer process to recycle these acids. At first, we manufactured the fluoride compound in form of $Na_2SiF_6$ by precipitating HF using $NaNO_3$ and Si powder. The concentration of HF was reduced from the initial concentration of 127 g/L to 0.5 g/L with an HF recovery ratio of 99.5%. After the manufacture of $Na_2SiF_6$, the concentration of $HNO_3$ and $CH_3COOH$ demonstrated 502 g/L and 117 g/L respectively. Following these findings we added NaOH in this $CH_3COOH/HNO_3$ mixed acid in order to obtain pH=4. Next we separated the $CH_3COOH$ and recoverd it through the use of vaccum evaporation at -440 mmHg, $95^{\circ}C$. The concentration of the recovered $CH_3COOH$ was approximately 15% and the recovery ratio of $CH_3COOH$ was over 85%. We precipitated the $NaNO_3$ by cooling the concentrated solution to $20^{\circ}C$ with a $HNO_3$ recovery ratio of over 93%. We confirmed that only $Na_2SiF_6$ and $NaNO_3$ were manufactured by XRD analysis after drying these precipitants at $90^{\circ}C$. The precipitants demonstrated a purity of approximately 97% and 98% respectively. Therefore, the purity of the precipitants proved to be similar to that of commercial products.

• Journal of Environmental Health Sciences
• /
• v.14 no.1
• /
• pp.63-71
• /
• 1988

This study is an experimental research on the anaerobic digestion of pig manure and night soil mixed waste at room temperature (25$\circ$C), and the results are shown below: 1. The steady-state condition based on gas production as digestion temperature dropped to 25$\circ$C from 35$\circ$C was achieved at around 28, 47, 56, 64 days respectively when its hydraulic retention time(HRT) are 10, 20, 30, 40 days. 2, Alkalinity and volatile acid(VA) was increased as increasing the organic loading. 3. Removal efficiency of chemical oxygen demand(COD) and biochemical oxygen demand (BOD) was improved as longer HRT, and generally COD value is lower and BOD value is higher relatively. 4. Overall treatment efficiencies of mixed waste are higher than of pig manure and of night soft. 5. Organic removal efficiency at room temperature (25$\circ$C) is 20-25% lower at medium temperature (35$\circ$C) in a same VS loading condition. 6. Refractory fraction of the infiuent VS and organic removal rate constant(K) estimated at around 37% and 0.107/day respectively.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.7
• /
• pp.969-976
• /
• 2004

Cassava peelings waste, which is both a waste and pollutant, was chemically modified using mercaptoacetic acid (MAA) and used to adsorb $Cu^{2+}\;and\;Cd^{2+}$ from aqueous solution over a wide range of reaction conditions at $30^{\circ}C$. Acid modification produced a larger surface area, which significantly enhanced the metal ion binding capacity of the biomass. An adsorption model based on the $Cu^{2+}/Cd^{2+}$ adsorption differences was developed to predict the competition of the two metal ions towards binding sites for a mixed metal ion system. The phytosorption process was examined in terms of Langmuir, Freundlich and Dubinin-Radushkevich models. The models indicate that the cassava waste biomass had a greater phytosorption capacity, higher affinity and greater sorption intensity for $Cu^{2+}\;than\;Cd^{2+}$. According to the evaluation using Langmuir equation, the monolayer binding capacity obtained was 127.3 mg/g $Cu^{2+}$ and 119.6 mg/g $Cd^{2+}$. The kinetic studies showed that the phytosorption rates could be described better by a pseudo-second order process and the rate coefficients was determined to be $2.04{\times}10^{-3}\;min^{-1}\;and\;1.98{\times}10^{-3}\;min^{-1}\;for\;Cu^{2+}\;and\;Cd^{2+}$ respectively. The results from these studies indicated that acid treated cassava waste biomass could be an efficient sorbent for the removal of toxic and valuable metals from industrial effluents.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.06a
• /
• pp.158-166
• /
• 2004

The optimal conditions are obtained for the decomposition of solid radioactive wastes, including ion exchange resin, zeolite, active charcoal, and sludge from nuclear power plant. In the process of decomposing the radioactive wastes were used the microwave acid digestion method with mixed acid. The solution after acid digestion by the following method was colorless and transparent. Each solution was analyzed with ICP-AES and AAS and the recovery yield for 5 different elements added the simulated radioactive wastes were over 94%. As an effective pre-treatment, the proposed microwave acid digestion conditions concerning the chemical trait of each radioactive waste are expected to be generally applied to above-mentioned radioactive wastes from nuclear power plant hereafter.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2005.10a
• /
• pp.59-61
• /
• 2005

In Korea, hundreds of abandoned and closed coal and metallic mines are present in the steep mountain valleys due to the depression of the mining industry since the late 1980s. From these mines, enormous amounts of coal waste were dumped on the slopes, which causes sedimentation and acid mine drainage (AMD) to be discharged directly into streams causing detrimental effects on soil and water environments. A limestone slurry by-product (lime cake) is produced from the Solvay process in manufacturing soda ash. It has very fine particles, low hydraulic conductivities ($10^{-8}{\sim}10^{-9}cm/sec$), high pH, high EC due to the presence of CaO, MgO and $CaCl_2$ as major components, and traces of heavy metals. Due to these properties, it has potential to be used as a neutralizer for acid-producing materials. A field plot experiment was used to test the application of lime cake for reclaiming coal wastes. Each plot was 20 x 5 m (L x W) in size on a 56% slope. Treatments included a control (waste only), calcite ($CaCO_3$), and lime cake. The lime requirement (LR) for the coal waste to pH 7.0 was determined and treatments consisted of adding 100%, 50%, and 25% of the LR. The lime cake and calcite were also applied in either a layer between the coal waste and topsoil or mixed into the topsoil and coal waste. Each plot was hydroseeded with grasses and planted with trees. In each plot, surface runoff and subsurface water were collected. The lime cake treatments increased the pH of coal waste from 3.5 to 6, and neutralized the pH of the runoff and leachate of the coal waste from 4.3 to 6.7.