• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.63-70
• /
• 1995

A crack-free ceramic composite membrane with micropores has been synthesized by the pressurized sol-gel coating technique using the mixed Al2O3-SiO2 sols. The mixed sols were prepared by mixing nanoparticulate SiO2 and boehmite sols. These sols were more stable at lower pH, but very unstable when their copositions were in the range of 50~75mol% of SiO2 at the same pH. The mixed Al2O3-SiO2 membrane prepared from the mixed sol (0.2mol/$\ell$ of solid content and pH=2) containing 40mol% of SiO2 had the mean pore radius of 0.80nm and the specific surface area of 280$m^2$/g. The nitrogen permeability through the coated Al2O3-SiO2 layer was 42$\times$107mol/$m^2$.s.Pa. It was found that the thermal stability of aluminosilicate membranes, even through similar to that of SiO2 membranes, was much improved in comparison with ${\gamma}$-alumina membranes.

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.708-712
• /
• 2009

ITO films were achieved by sintering at $500{\sim}550{^{\circ}C}$. This was possible by inducing a seeding effect on an ITO sol by producing crystalline ITO nanoparticles in situ during heat treatment. Two kinds of ITO sols (named ITO-A and ITO-B) were prepared at 2.0 wt% from indium acetate and tin(IV) chloride in different mixed solvents. The ITO-A sol showed a high degree of crystallinity of ITO without any detectable Sn$O_2$ on XRD at $350{^{\circ}C}$/1 h, but the ITO-B sol showed a small amount of Sn$O_2$ even after annealing at $600{^{\circ}C}$/1 h. The 10 wt% ITO-A//ITO-B showed the sheet resistance of 3600$\Omega$/□, while the ITO-B sol alone showed 5200 $\Omega$/□ by sintering at $550{^{\circ}C}$ for 30 min. Processing parameters were studied by TG/DSC, XRD, SEM, sheet resistance, and visible transmittance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.9
• /
• pp.967-972
• /
• 2004

Hardness and surface property of coated gel materials are considerably different according to kinds(particle size/stabilized ion) of colloidal silica(CS), kinds of silanes, content ratio of silane versus CS, and reaction degree in sol solution. We report the properties of sol-gel coating materials in which the factors of reaction are kinds of CS, contents ratio of CS and MTMS, and reaction time of sol. The contact angles of the coated films obtained from the mixed CS system showed a little good relationship with MTMS content increase to those from HSA CS reaction system and the change of contact angle didn't have much effect on reaction time of sol. In the coating films obtained from HSA CS reaction system, the surface was much rough in case of that the content MTMS decreased and the reaction of sol kept long. The surface roughness of films obtained from the mixed CS reaction system showed similar tendency, though its degree was a little different. In synthesis of sol-gel coating materials, we could identify that choice of CS kinds and content ratio of CS and silane were important and it was desirable the reaction time of sol is not long.

• Korean Journal of Materials Research
• /
• v.17 no.4
• /
• pp.185-191
• /
• 2007

The purpose of this study is to evaluate the thin fihn dielectric made of hybrid sol, which consist of barium titanate powder, polymeric sol and other polymers. This sol will be used dielectric applied to small, thin electric passive components such as MLCC(Multi Layer Ceramic Condenser), resister, inductor. This sol is composed of mixed fine barium titanate powder and polymeric sol including Ba, Ti-precursor, solvent, chelating agent, chemical reaction catalyst, the additive sols to improve fired densification and temperature reliability. First at all, we mixed hybrid sol to be dispersed and be stabilized by ball milling for 24hrs. By spin coating method, we makes thin film dielectric on the convectional green sheet for MLCC. After heat treatments, we analyzes the structure morphology, physical, electrical properties and X5R Temperature properties.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1930-1932
• /
• 2005

Colloidal Silica(CS)/methyltrimethoxy silane(MTMS) and CS/MTMS/epoxy silane(Es) sol solutions were prepared in variation with synthesizing parameters such as kinds of CS, kinds of silane and reaction time. In order to understand its physical and chemical properties, sol-gel coating films on glass were fabricated. In the case of CS/MTMS sol, the coating films had high contact angle and more enhanced flat surface than those in the case of CS/MTMS/ES sol. Also, the coating films obtained from single CS had a better flat surface than those obtained from mixed CS. In the case of thermal stability, thermal dissociation of CS/MTMS and CS/MTMS/ES sol-gel coating films did not occur up to $550^{\circ}C$ and $440^{\circ}C$ respectively. The thickness of coating films obtained from CS/MTMS sol increased than those of CS/MTMS/ES sol. In addition, the coating films obtained from single CS were more thicker than those obtained from mixed CS.

• Journal of the Korean Ceramic Society
• /
• v.28 no.12
• /
• pp.1012-1018
• /
• 1991

SiC whisker-reinforced LAS matrix composites were developed by a mixed colloidal processing route. An optimization of processing conditions was made using the zeta potential data of silica, boehmite, and SiC whisker dispersions. Similarly, the SiC whisker-reinforced composites were also fabricated by the conventional sol-gel process using the hydrolysis-condensation reaction of relevant metal alkoxides. The composites fabricated by the mixed colloidal processing route were characterized by a uniform spatial distribution of SiC whisker throughout the matrix. The fracture toughness increased from 1.3 MPa.m1/2 for the LAS specimen to 5.0 Mpa.m1/2 for the hot-pressed composite (95$0^{\circ}C$ and 20 MPa for 20 min) containing 20 wt% SiC whisker. The increase in fracture toughness appears to result mainly from the crack deflection and the crack bridging by whiskers with some additional toughenings from the whisker pullout and the matrix prestressing mechanisms.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.05a
• /
• pp.108-109
• /
• 1993

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.4
• /
• pp.883-891
• /
• 2017

For the preferential oxidation of CO contained in the fuel of polymer electrolyte membrane fuel cell (PEMFC), CuO-$CeO_2$ mixed oxide catalysts were prepared by the sol-gel and co-precipitation methods to replace noble metal catalysts. In the catalyst preparation by the sol-gel method, Cu/Ce ratio and hydrolysis ratio were changed. The catalytic activity of the prepared catalysts was compared with the catalytic activity of the noble metal catalyst($Pt/{\gamma}-Al_2O_3$). Among the catalysts prepared with different Cu/Ce ratios, the catalyst whose Cu/Ce ratio was 4:16 showed the highest CO conversion (90%) and selectivity (60%) at $150^{\circ}C$. As the hydrolysis ratio was increased in the catalyst preparation, surface area increased, and catalytic activity also increased. The highest CO conversions with the CuO-$CeO_2$ mixed oxide catalyst prepared by the co-precipitation method and the noble metal catalyst (1wt% $Pt/{\gamma}-Al_2O_3$) were 82 and 81% at $150^{\circ}C$, respectively, whereas the highest CO conversion with the CuO-$CeO_2$ mixed oxide catalyst prepared by the sol-gel method was 90% at the same temperature. This indicates that the catalyst prepared by the sol-gel method shows higher catalytic activity than the catalysts prepared by the co-precipitation method and the noble metal catalyst. From the CO-TPD experiment, it was found that the catalyst having CO desorption peak at a lower temperature ($140^{\circ}C$) revealed higher catalytic activity.

• Journal of the Korean Ceramic Society
• /
• v.28 no.11
• /
• pp.865-872
• /
• 1991

LAS (lithium aluminosilicate) sol was synthesized using the hydrolysis-condensation reaction of TEOS, chelated Al(OBus)3 and LiNO3 with H2O in alcohol (ethanol+2-propanol) medium. Lowering Li content by a factor of 1/2 significantly enhanced densification and retarded the crystallization of LAS gel by ~30$0^{\circ}C$. Dense LAS specimen with essentially pore-free microstructure was obtained by sintering the sol-gel derived gel at 80$0^{\circ}C$ for 4 h and annealing at 120$0^{\circ}C$ for 2 h. Similary, a mixed colloidal processing was attempted as a convenient, alternative route for the fabrication of dense LAS sintered body. The $\beta$-spodumene seeding (~0.8 ${\mu}{\textrm}{m}$) in the sol-gel derived LAS modified the sequence of phase transformations and lowered the temperature of crystallization by ~12$0^{\circ}C$. Combining the epitaxial seeding with the sol-gel process, we could lower the crystallization temperature to the sintering temperature range (~80$0^{\circ}C$) and, demonstrate a possibility of making the viscous sintering/crystallization as a continuous as a continuous unit process.

• Electrical & Electronic Materials
• /
• v.7 no.6
• /
• pp.496-503
• /
• 1994

In recent years Sol-Gel processing provides an interesting alternative method for the fabrication of ferroelectric thin layers and powder. PZT powder was prepared from an alkoxide-based solution by a Sol-Gel method. Gelation of synthesized complex solutions, microstructure, thermal analysis and crystallization behaviors of the calcined powder were studied in accordance with a water content and a catalyst. Especially gelation and crystallization behavior were analysed with the change of pH. The gelation time decreased as the pH of the mixed solution increased. For PZT powder with 650.deg. C heat treatment, 100% perovskite phase was formed by using either acidic or basic catalyst. By using either acidic or basic catalyst, we were able to get very fine powders of uniform shape with an average particle size of 0.8-1.mu.m.