• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.53-63
• /
• 2017

The increasing of wind power penetration level presents challenges in classical optimal reactive power dispatch (ORPD) which is usually formulated as a deterministic optimization problem. This paper proposes a two-stage stochastic programming model for ORPD by considering the uncertainties of wind speed and load in a specified time interval. To avoid the excessive operation, the schedule of compensators will be determined in the first-stage while accounting for the costs of adjusting the compensators (CACs). Under uncertainty effects, on-load tap changer (OLTC) and generator in the second-stage will compensate the mismatch caused by the first-stage decision. The objective of the proposed model is to minimize the sum of CACs and the expected energy loss. The stochastic behavior is formulated by three-point estimate method (TPEM) to convert the stochastic programming into equivalent deterministic problem. A hybrid Genetic Algorithm-Interior Point Method is utilized to solve this large-scale mixed-integer nonlinear stochastic problem. Two case studies on IEEE 14-bus and IEEE 118-bus system are provided to illustrate the effectiveness of the proposed method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.6
• /
• pp.120-127
• /
• 2014

Robustness and controllability are the key factors in internal combustion engine commercialization. This study focuses on the combustion strategy to commercialize the low temperature diesel combustion technology. Various LTC combustion methods such as PPCI, MK and highly diluted mixing controlled LTC were conducted on 6.0L heavy duty diesel engine. To find the best feasible LTC strategy, emission level, fuel consumption and combustion safety during the combustion mode change were considered. Experiments were carried out under various engine operating conditions; engine speed & load, EGR level, injection timing. Finally, this study suggests realizable LTC combustion strategy; moderate EGR level and slight early injection are possible to considerably lower PM, NOx emission and expand LTC operating range up to 50% load without CO and HC emission.

• Journal of Welding and Joining
• /
• v.6 no.3
• /
• pp.43-55
• /
• 1988

An experimental study was carried out to identify the fatigue fractue behavior of weld zone in generally rolled steel for marine structure. The bending an shear loads were applied simultaneously on the specimens to simulate real load condition for marine structure. The effect of the stress intensity factor under mode I with II loading condition on the initiation and the propagation of a crack were investigated, with particular emphaiss on mode II. When the $K_{II}$ stress intensiy factor in mode II was applied under mode I load condition, the growth behavior of a crack seems to be affected mainly by the anisotropic characteristic of materials. Especially, when the crack was located in and near the weld zone and parallel to th weld line, the propagation behaviour was turned out to be quite different from that of the base metal along the direction transverse to the weld line. In general, the propagation veiocity of the cracks in and near the weld zone was found to be slower that the velocity in base metal.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.5
• /
• pp.1709-1718
• /
• 2017

This paper presents a hybrid stochastic deterministic multi-timescale scheduling (SDMS) approach for generation scheduling of a power grid. SDMS considers flexible resource options including conventional generation flexibility in a chance-constrained day-ahead scheduling optimization (DASO). The prime objective of the DASO is the minimization of the daily production cost in power systems with high penetration scenarios of variable generation. Furthermore, energy storage is scheduled in an hourly-ahead deterministic real-time scheduling optimization (RTSO). DASO simulation results are used as the base starting-point values in the hour-ahead online rolling RTSO with a 15-minute time interval. RTSO considers energy storage as another source of grid flexibility, to balance out the deviation between predicted and actual net load demand values. Numerical simulations, on the IEEE RTS test system with high wind penetration levels, indicate the effectiveness of the proposed SDMS framework for managing the grid flexibility to meet the net load demand, in both day-ahead and real-time timescales. Results also highlight the adequacy of the framework to adjust the scheduling, in real-time, to cope with large prediction errors of wind forecasting.

• Journal of the Korean Society of Combustion
• /
• v.16 no.4
• /
• pp.1-7
• /
• 2011

The purpose of this study was to analyze the effect of pilot injection strategy on the combustion and emissions characteristics in a four cylinder common-rail direct injection diesel engine fueled with biodiesel(soybean oil) blend. The tested fuel was mixed of 20% biodiesel and 80% ULSD(Ultra low sulfur diesel) by volume ratio. The experiments were performed under two load conditions, and results were compared with those of single injection. The experimental results showed that the ignition delay of BD20 was shorter than compared to that of ULSD in the case of low load condition. Also, the fuel consumption of BD20 was more higher than that of ULSD. Fuel consumption by applied pilot injection strategy were generally decreased compared with that of single injection. In the case of pilot injection, the exhaust emissions such as CO and HC emissions were decreased compared to the single injection.

• Structural Engineering and Mechanics
• /
• v.5 no.4
• /
• pp.433-450
• /
• 1997

The objective of this work is to predict the failure loads, associated maximum transverse displacements, locations and the modes of failure, including the onset of delamination, of thin, flat, square symmetric laminates under the action of uni-axial compression. Two progressive failure analyses, one using Hashin criterion and the other using Tensor polynomial criteria, are used in conjunction with the finite element method. First order shear deformation theory and geometric nonlinearity in the von Karman sense have been employed. Five different types of lay-up sequence are considered for laminates with all edges simply supported. In addition, two boundary conditions, one with all edges fixed and other with mixed boundary conditions for $(+45/-45/0/90)_{2s}$ quasi-isotropic laminate have also been considered to study the effect of boundary restraints on the failure loads and the corresponding modes of failure. A comparison of linear and nonlinear results is also made for $({\pm}45/0/90)_{2s}$ quasi-isotropic laminate. It is observed that the maximum difference between the failure loads predicted by various criteria depend strongly on the laminate lay-ups and the flexural boundary restraints. Laminates with clamped edges are found to be more susceptible to failure due to the transverse shear and delamination, while those with the simply supported edges undergo total collapse at a load slightly higher than the fiber failure load.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.842-847
• /
• 2008

Despite of the increasing number of the application of the drilled shaft pile in construction site, most of the study of pile capacity has been centered side shear resistance. But it is common that the drilled shaft is socketed on the rock so as to use the bearing resistance, so prediction of the toe's movement and characteristic of the bearing capacity is important as the side shear resistance. Therefore the model tests were performed in order to study the characteristic of bearing capacity on rock mass. The material of the test blocks were the mortar which was mixed with sand, cement and water, and test block size was $240{\times}240{\times}240mm$. Load was pressed by the 45mm of diameter of miniaturized pile and plate jack and steal plate were used to the confined stress for representing the underground condition. The relation of load-displacement was measured in many different conditions of rock mass such as direction of discontinuities, spacing and strength, and q-w curves of the toe of the pile were verified in each condition.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.1166-1171
• /
• 2008

Despite of the increasing number of the application of drilled shaft piles in construction site, most studies on pile capacity have been focused on the side shear resistance. But it is common that the drilled shaft is socketed on the rock so as to use its bearing resistance. The prediction of the end movement and characteristics of the bearing capacity of the pile is great important as well. Therefore, a series of scaled model tests were carried out in order to study the characteristics of the bearing capacity on rock mass. The material of the test block was cement mortar which was mixed with sand, cement and water, and the size of a test block size was $240{\times}240{\times}240mm$. The axial load was applied by a miniaturized pile of 45mm in diameter and flat jacks and steel plate were used for confinement to simulate the real underground loading conditions. The relation of load-displacement was measured in various different conditions of rock mass such as strength, discontinuity of the rock mass and in-situ stress, so q-w curves of the end of the pile were presented for each condition.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.5C
• /
• pp.422-434
• /
• 2002

We propose 3-layered hierarchical fiber-optic backbone transmission network composed of B-DCS, Backbone ring, Edge ring for efficient transmission of high capacity traffic and consider design method to ensure network survivability of each layer at affordable cost. Mathematical ring-construction cost minimization using MIP(Mixed Integer Programming) models results in NP-complete problem. So, it is hard to solve it within reasonable computing time. on a large-scale network. Therefore we develop heuristic algorithms solving WSCAP(Working and Spared Channel Assignment Problem) for B-DCS, MRLB(Multi-Ring Load Balancing) problem for Backbone ring, and ORLB(Overlayed Ring Load Balancing) problem for Edge ring and show their usefulness through case study.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.800-805
• /
• 2001

Recently, our world is faced with very serious and hard problems related to the air pollution due to the exhaust emissions of the diesel engine. So, lots of researchers have studied to reduce the exhaust emissions which influenced the environment strong. In this paper, the effect of oxygen component in fuel on the exhaust emissions has been investigated for diesel engine. And, we tried to analysis the quantities of the low and high hydrocarbon among the exhaust emissions in diesel engine. It have been investigated by the quantitative analysis of the hydrocarbon $C_1\simC_6$ using the gas chromatography. This study carried out by comparing the chromatogram with diesel fuel and diesel fuel blended DGM(diethylene glycol dimethyl ether) 5%. The results of this study show that the hydrocarbon $C_1\simC_6$ among the exhaust emissions of the mixed fuels are exhausted lower than those of the diesel fuel at the all load and speed. In particular, high boiling point hydrocarbons such as $C_5$ and $C_6$ were reduced remarkably in high speed and load region.