• KEPCO Journal on Electric Power and Energy
• /
• 제1권1호
• /
• pp.15-20
• /
• 2015

To examine the magnetic shielding effect for carbon-based materials at extremely low frequencies (60 Hz), two types of carbon black (Super-P and Denka Black) and a natural graphite (HC-198) were mixed into organic binder at 10 wt.% to produce a coating solution, and a powder coating with varying thickness was applied on an aluminum disk measuring 88 mm in radius. A device was developed to measure the sheielding effect at extremely low frequencies. A closed circuit was achieved by connecting a transformer and a resistor. The applied voltage was fixed at 65 V, and the magnetic field was measured to being the range of 4.95~5.10 mG. Depending on the thickness of the coating layer, the magnetic field showed a decreasing trend. The maximum decrease in the magnetic field of 38.3% was measured when natural graphite was coated with specimens averaging $455{\mu}m$. This study confirmed that carbon-based materials enable magnetic shielding at extremely low frequencies, and that the magnetic shielding effect can be enhanced by varying the coating thickness.

• 한국세라믹학회지
• /
• 제46권6호
• /
• pp.708-712
• /
• 2009

ITO films were achieved by sintering at $500{\sim}550{^{\circ}C}$. This was possible by inducing a seeding effect on an ITO sol by producing crystalline ITO nanoparticles in situ during heat treatment. Two kinds of ITO sols (named ITO-A and ITO-B) were prepared at 2.0 wt% from indium acetate and tin(IV) chloride in different mixed solvents. The ITO-A sol showed a high degree of crystallinity of ITO without any detectable Sn$O_2$ on XRD at $350{^{\circ}C}$/1 h, but the ITO-B sol showed a small amount of Sn$O_2$ even after annealing at $600{^{\circ}C}$/1 h. The 10 wt% ITO-A//ITO-B showed the sheet resistance of 3600$\Omega$/□, while the ITO-B sol alone showed 5200 $\Omega$/□ by sintering at $550{^{\circ}C}$ for 30 min. Processing parameters were studied by TG/DSC, XRD, SEM, sheet resistance, and visible transmittance.

• 분석과학
• /
• 제6권2호
• /
• pp.207-215
• /
• 1993

소결첨가제($3Al_2O_3{\cdot}5Y_2O_3$, YAG)를 질화규소에 공침방법으로 첨가하여, 통상적인 기계적 혼합 방법으로 준비된 혼합분말에 대한 혼합균일성과 소결 및 기계적 특성을 조사, 비교하였다. 준비된 혼합분말들을 SIMS를 사용하여 분말 표면과 내부의 조성을 비교분석한 결과, 공침법을 사용할 경우 소결첨가제가 $Si_3N_4$ 표면에 피복된 상태로 존재하고 있음을 나타내어 기계적 혼합에 비해 우수한 균일혼합효과를 얻을 수 있음을 확인하였다. 공침법에 의한 균일혼합효과는 $Si_3N_4$ 분말소결체의 소결밀도 및 미세구조의 개선을 수반하여 기계적 강도의 향상을 이룰 수 있음을 확인하였다.

• 한국표면공학회지
• /
• 제50권2호
• /
• pp.85-90
• /
• 2017

The carbon steel formed the thick, somewhat porous, loosely adherent iron oxide scale when oxidized at $500-800^{\circ}C$ for 15 h in air. It formed the thicker, more porous, nonadherent scale consisting of FeS plus iron oxides in $Ar/1%SO_2$-mixed gas. It formed the much thicker, more porous, nonadherent scale consisting of FeS plus iron oxides in Ar/0.1% $H_2S$-mixed gas. However, the aluminized carbon steel formed the thin, protective $Al_2O_3$ surface scale even in $Ar/1%SO_2$-, and $Ar/0.1%H_2S$-mixed gas. Aluminizing drastically improved the corrosion resistance in (O, S, H)-containing gas.

• Membrane and Water Treatment
• /
• 제9권2호
• /
• pp.105-113
• /
• 2018

Maillard reaction products like melanoidins present in industrial fermentation wastewaters are complex compounds with various functional properties. In this work, novel ultrafiltration (UF) mixed matrix membrane (MMM) composed of polysulfone (PSF) and nanocomposites was prepared through a phase inversion process for the recovery of melanoidins. Nanocomposites were prepared with acid functionalized multiwalled carbon nanotubes (MWCNTs) as the reinforcing filler for chitosan-thermoplastic starch blend. Higher nanocomposites content in the PSF matrix reduced the membrane permeability and melanoidins retention indicating tighter membrane with surface defects. The membrane surface defects could be sealed with dilute polyvinyl alcohol (PVA) solution. The best performing membrane (1% nanocomposites in 18% PSF membrane sealed with 0.25% PVA coating) resulted in uniform melanoidins retention of 98% and permeability of 3.6 L/m2 h bar over a period of 8h. This demonstrates a low fouling PSF membrane for high melanoidins recovery.

• 한국재료학회지
• /
• 제33권5호
• /
• pp.195-204
• /
• 2023

Micro-electronic gas sensor devices were developed for the detection of carbon monoxide (CO), nitrogen oxides (NO_x), ammonia (NH₃), and formaldehyde (HCHO), as well as binary mixed-gas systems. Four gas sensing materials for different target gases, Pd-SnO₂ for CO, In₂O₃ for NO_x, Ru-WO₃ for NH₃, and SnO₂-ZnO for HCHO, were synthesized using a sol-gel method, and sensor devices were then fabricated using a micro sensor platform. The gas sensing behavior and sensor response to the gas mixture were examined for six mixed gas systems using the experimental data in MEMS gas sensor arrays in sole gases and their mixtures. The gas sensing behavior with the mixed gas system suggests that specific adsorption and selective activation of the adsorption sites might occur in gas mixtures, and allow selectivity for the adsorption of a particular gas. The careful pattern recognition of sensing data obtained by the sensor array made it possible to distinguish a gas species from a gas mixture and to measure its concentration.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권6호
• /
• pp.29-36
• /
• 2015

본 연구에서는 유황을 폴리머화하여 콘크리트 표면보호재로 활용가능성을 검토하기 위하여 내구성능 및 생물독성 평가를 실시하였다. 평가 결과, 콘크리트 표면보호재의 내화학성능은 산, 알칼리 용액에 대하여 화학저항성이 우수한 것으로 나타났다. 배합조건별 촉진내후성 실험 후 부착강도평가 결과 규사분말 및 플라이애시를 동시에 혼합한 배합에서 가장 우수한 강도특성을 나타내었다. 콘크리트용 표면보호재 시험체의 온냉반복 후에도 모든 배합조건에서 부착강도 1 MPa을 상회하였고, SFS배합에서 가장 높은 부착강도를 나타내었다. 표면보호재를 도포한 콘크리트의 촉진탄산화 및 염소이온침투저항성을 검토한 결과, 규사분말을 채움재로 사용한 표면보호재를 도포한 시험체에서 가장 우수한 내구성능을 나타내었다. 유황폴리머를 콘크리트 표면보호재로 사용시 생물독성 검토를 위해 어독성 실험을 수행한 결과, 유황폴리머는 생물에 미치는 영향은 없는 것으로 나타났다. 표면보호재의 내화학성, 동결융해저항성, 탄산화, 염소이온침투저항성 등을 모두 고려하여 볼 때, 본 연구범위에서는 유황폴리머에 채움재로서 규사분말과 플라이애시를 각각 20%씩 대체하는 것이 적절한 수준인 것으로 판단된다.

• 보존과학회지
• /
• 제32권2호
• /
• pp.109-121
• /
• 2016

나전대모칠기는 나전, 대모, 금속선 등을 사용하여 가식한 것으로 금속분을 기물 전체에 뿌려 전체적으로 밝은 색조로 표현한 특징을 가진다. 본 연구는 칠도막 단면을 광학현미경과 SEM-EDS 분석을 통하여 칠도막 단면에 나타나는 재료와 특성을 밝히고자 하였다. 그 결과, 목탄분과 토분을 섞은 바탕칠 위에 진사와 석황이 섞인 칠을 바르고, 그 위에 황동분을 뿌린 것으로 나타났다. 칠층에 섞여 있는 안료의 양은 소량으로 종래의 문양 표현에 쓰인 색칠과는 구별된다. 특히, 나전대모칠기의 칠층에서 진사와 석황의 두 가지 안료를 혼합하여 사용한 예를 확인할 수 있었다.

• 한국도로학회논문집
• /
• 제14권1호
• /
• pp.45-53
• /
• 2012

본 연구에서는 다양한 포장용 콘크리트 배합의 건조수축 특성에 관한 실험결과를 분석하였다. 실험변수는 굵은골재의 종류(석회암, 사암, 화강암, 안산암, 편마암)와 잔골재의 종류(자연사, 부순모래) 및 콘크리트의 배합강도(보통강도, 고강도)를 달리하였다. 그리고 형상비가 22.2, 40, 85.7, 150, 200, 300을 갖도록 시편의 크기를 달리하였으며 코팅제(U&V-H(A,B))를 활용하였다. 다이얼게이지를 이용하여 항온($20^{\circ}C$) 항습(60%)에서 수행된 건조수축 실험은 길게는 1,014일 동안 측정하였다. KS에서 제시하는 표준시편에 비해 도로포장 모사용 슬래브 시편의 건조수축 변형률은 약 39% 감소되는 것으로 나타났다. 또한 동일한 형상비에 대해 굵은골재의 변화에 따른 건조수축 실험결과 석회암이 배합된 시편의 변형률이 사암대비 형상비별로 56~76% 범위에서 가장 낮게 측정되어 포장용 콘크리트로 사용되는데 유리할 것으로 판단된다.

• 한국재료학회지
• /
• 제23권7호
• /
• pp.353-358
• /
• 2013

To improve coating ability and the life of the coating, Ti based composite materials with hydroxyapatite(HA) should be developed. The raw materials of Ti-26wt%, Nb-1wt%, and Si with 10wt% HA were mixed for 24 h by a mixing machine and milled for 1 h to 6 h by planetary mechanical ball milling. Ti-26%Nb-1%Si-(10%HA) composites, composed of nontoxic elements, were fabricated successfully by spark plasma sintering(SPS) at $1000^{\circ}C$ under 70MPa. The relative density of the sintered Ti-Nb-Si-HA composites using the 24 h mixed powder, and the 6 h milled powder, was 91% and 97 %, respectively. The effects of HA contents and milling time on microstructure and mechanical properties were investigated by SEM and hardness tester, respectively. The Vickers hardness of the composites increased with increasing milling time and higher HA content. The Young's modulus of the sintered Ti-26%Nb-1%Si-10%HA composite using the 6 h-milled powder was 55.6 GPa, as obtained by compression test. Corrosion resistance of the Ti-26wt%Nb-1wt%Si composite was increased by milling and by the addition of 10wt%HA. Wear resistance was improved with increasing milling time. Biocompatibility of the Ti-Nb-Si alloys was improved by the addition of HA.