• 한국표면공학회지
• /
• 제32권6호
• /
• pp.686-694
• /
• 1999

Insoluble anodes of the Ta/Ir mixed metal oxide for electrodeposition of Ni-W alloy in ammoniacal citrate bath were prepared by thermal decomposition method. Ti plate was etched in boiling oxalic acid solution and coated with ethanol solution of $TaCl_{5}$ and $IrCl_4$ mixed in a fixed ratio, followed by drying and treating at various temperatures. The coating layer of these insoluble anode was characterized by SEM, EDX, XRD and DSC. The decomposition rate of citric acid in plating bath was determined by measuring the $CO_2$ gas evolved at the anodes with Gas Chromatography. Evolution of $CO_2$ gas from Ta/Ir oxide anodes decreased about 5% compared with that of Pt. The $CO_2$ gas evolution was increased with the amount of Ir-oxide in the coatings. The coatings which have more than 40% ratio of Ta content and heat-treated at the temperature higher than $400^{\circ}C$ showed better efficiency

• KIEE International Transactions on Electrophysics and Applications
• /
• 제3C권4호
• /
• pp.136-139
• /
• 2003

The positive column of a discharge tube filled with a mixture of mercury-xenon has a tendency to become contracted at room temperature. However, once the tube temperature is raised over 50 [$^{\circ}C$], the positive column changes from a contracted state to a diffused state. The xenon emission is stronger in the contracted positive column than in the diffused column. Alternatively, the mercury emission is more intense in the diffused positive column, and the luminance of the phosphor coating on the inner surface of the tube is higher than that in the contracted positive column. Moreover, higher luminance can be obtained by increasing the xenon pressure.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 추계 학술논문 발표대회
• /
• pp.126-127
• /
• 2017

This study investigates the effect of improving the heat resistance performance when carbon fiber is mixed in the polyurea coating material. A tensile strength test method was carried out with the carbon fiber mixed polyurea specimens at an interval of 7, 14, and 21 days after heat treatment at 140±2℃. The test results showed that there was a significant decrease in the tensile strength performance. While the elongation and tensile performance decreased greatly, it was confirmed nevertheless the overall performance was maintained. This study proposes that mixing carbon fiber to the polyurea resin can effectively secure long-term heat resistance, thereby solving the problem of deterioration of physical properties caused by exposure to ultraviolet rays.

• 한국표면공학회지
• /
• 제31권4호
• /
• pp.191-198
• /
• 1998

The effect of the additives on the Zn-Ni alloy electrocrystallization from a chloride bath was investigated by means of electrochemical methodes, scanning electron microscopy and measurement of surface appearancd, X-ray diffraction patterns. The additives thestd ware the Saccharin, surfactant of naptalene-derivative and mixed additive, The resistance of electrodeposit increased by adding the additives, whera the effect of additives on resistance was different with current density roughness, apperarance and morphology of deposit were also influenced by the type of additive. The deposir with fine, compact grains as well as good surface roughness and appearance was obtained from the mixed-additive added bath.

• 한국재료학회지
• /
• 제22권12호
• /
• pp.696-700
• /
• 2012

(Na, K) $NbO_3$ thick film was successfully achieved using a sol-gel coating process with the addition of polyvinylpyrrolidone (PVP) to a metal alkoxide solution. The transparent coating solution, mixed with Nb:PVP = 1:1 in a molar ration, was synthesized by evaporating the solvent to over 62.5 wt%. Additive PVP increased the viscosity of the solution so that the coating thickness could be enhanced. The thickness of the (Na, K) $NbO_3$ film assisted by PVP was ca. 320 nm at the time of deposition; this value is four times thicker than that of the sample fabricated without PVP. Also, due to PVP binding with the OH groups of the metal alkoxide, the condensation reaction in the film was suppressed. The crystalline size of the (Na, K) $NbO_3$ films assisted by PVP was ca. 15 nm smaller than that of the film fabricated without PVP. After the sintering process at $700^{\circ}C$, the (Na, K) $NbO_3$ films were mainly composed of randomly oriented (Na, K) $NbO_3$ phase of perovskite crystal structure, including a somewhat secondary phase of $K_2Nb_4O_{11}$. However, by adding PVP, the content of the secondary phase became quite smaller than that of the sample without PVP. It was thought that the addition of PVP might have the effect of restraining the loss of potassium and that PVP could hold metalloxane by strong hydrogen bonding before complete decomposition. Therefore, the film thickness of the (Na, K) $NbO_3$ films could be considerably advanced and made more crack-free by the addition of PVP.

• 열처리공학회지
• /
• 제27권1호
• /
• pp.10-14
• /
• 2014

Niobium nitride coatings have many potential thin film applications due to their chemical inertness, good mechanical properties, temperature stability and superconducting properties. In this study, $NbN_x$ coatings were prepared by inductively coupled plasma (ICP) assisted DC magnetron sputtering method on the surface of AISI 304 austenitic stainless steels. Effects of target power were studied on mechanical and chemical properties of the coatings. The coating structure was analyzed by X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). The coating hardness was measured by micro-knoop hardness tester. The coating thickness was measured using a 3D profiler and wear characteristics were estimated using a ball-on-disk wear tester. The thickness of the $NbN_x$ coatings increased linearly from 300 nm to 2000 nm as the Nb target power increased, and it showed over $HK_{0.005}$ 4000 hardness above Nb target power of 300 W. Hexagonal ${\delta}^{\prime}$-NbN phase and cubic ${\delta}$-NbN phase were observed in the coating films and the hardness of the NbNx coatings was higher when these two peaks were mixed. The corrosion resistance increased with the increase of the Nb target power.

• Korean Chemical Engineering Research
• /
• 제52권4호
• /
• pp.451-458
• /
• 2014

Isophrone diisocyanate (IPDI), polycarbonate diol (PCD)과 dimethylol propionic acid (DMPA)를 출발물질로 하여 수분산 폴리우레탄(waterborne polyurethane dispersion, WPUD)을 합성하였다. 이 WPUD에 아크릴 단량체인 methyl methacrylate (MMA), 2-hydroxyethyl methacrylate (HEMA)와 butyl acrylate (BA)를 각각 첨가하여 다양한 종류의 수분산 아크릴 폴리우레탄(waterborne acrylic polyurethane dispersion, AUD)을 합성하였다. 이 AUD와 물에 분산된 다중벽 탄소나노튜브(multi-walled carbon nanotube, MWCNT)를 혼합하여 전도성 코팅 용액을 제조한 후 polycarbonate 시트 위에 도포하여 코팅 도막을 형성하고 물성을 살펴보았다. AUD로부터 제조된 코팅 도막의 연필경도, 내마모성 및 내약품성은 WPUD 보다 향상되었으나, 전기 전도도는 감소하였다. 또한 아크릴 단량체의 종류 변화 실험에서는 코팅 도막의 연필경도는 HEMA를 사용한 경우가 가장 우수하였으나, 내마모성, 내약품성 및 전기 전도도는 MMA를 사용한 경우가 가장 우수하였다.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2013년도 추계학술대회
• /
• pp.46-47
• /
• 2013

오염물질이 처리된 해양저질을 이용하여 황산염, 질산염 및 아세테이트 등의 생물활성물질을 첨가하여 생물활성촉진볼을 제작하였으며, 셀룰로스 아세테이트 코팅(CA)과 폴리설펀 코팅(PS) 방법으로 표면을 처리하여 생물활성촉진물질의 용출율을 조절하고자 하였다. SEM 분석으로 평가한 생물활성촉진제의 형태적 특성은 CA의 경우, 내부코팅층은 비교적 큰 공극이 다소 존재하였으며, 외부 코팅층은 균일하고 촘촘한 벌집모양의 공극이 분포되어있었고, PS의 경우, 내부코팅층과 외부코팅층의 모양이 동일하고, 무공극층이 형성된 것으로 나타났다. 코팅방법에 따른 생물활성촉진물질의 용출율은 증류수조건에서보다 해수조건에서 다소 높았고, 질산염이 황산염에 배해 다소 빨리 용출되었으며, 정체조건에 비해 난류조건에서 약 50%이상 높았다.

• Advances in environmental research
• /
• 제8권1호
• /
• pp.71-84
• /
• 2019

Effective waterproofing of structures was a compulsory constraint to avoid leaks and dampness or humidity in walls, ceilings, roofs underground tank and underground room. Traditionally used methods of roof waterproofing were bitumen with tinny seared clay tiles are very troublesome, overwhelming time and involving high labor cost. These waterproofing methods are not allocation the purpose due to their intrinsic disadvantages. Prepackaged polymer modified slurries (PPPMS) are now attainment the vogue and easy to use, easily available in the market, cheaper in cost and more workable than the traditional methods of waterproofing. An experimental study has shown that prepackaged polymer modified slurries (PPPMS) are superior in cost and performance to as a roof water proof coatings. Bituminous coatings were mixed with water and different combination of prepackaged polymer modified slurries and primer respectively, to find optimum coverage underneath worst atmospheric conditions. Every specimen of different proportioned was applied on plane roofs and through the passage of time, their performance was checked, assessed and associated with each other. The roof of approximately 40000 ft² area of prepackaged polymer modified slurries was used will give us hundred percent result (no water seepage or no water absorption) therefore no complaints as compare to roofs area of approximately 24000 ft² bituminous coating was used for waterproofing they have shown the result of 30 to 40 percent water seepage. This result shows that prepackaged polymer modified slurries were two times cheaper than bituminous coating. Comparing an equal number of surfaces coated with a polymer modified prepackaged mortar and bitumen the prepackaged polymer modified slurries (PPPMS) showed excellent performance, ease of application and low bitumen coating cost.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2010년도 춘계학술발표대회
• /
• pp.6.2-6.2
• /
• 2010

Stainless steel is widely known to have superior corrosion properties. However, in some harsh conditions it still suffers various kinds of corrosions such as galvanic corrosion, pitting corrosion, intergranular corrosion, chloride stress corrosion cracking, and etc. For the corrosion protection of stainless steel, the ceramic coatings such as protective silica film can be used. The sol-gel coating technique for the silica film has been extensively studied especially because of the cost effectiveness. It has been proved that silica can improve the oxidation and the acidic corrosion resistance of metal surface in a wide range of temperatures due to its high heat and chemical resistance. However, in the sol-gel coating process there used to engage a heat treatment at an elevated temperature like $500^{\circ}C{\sim}600^{\circ}C$ where cracks in the silica film would be formed because of the thermal expansion mismatch with the metal. The cracks and pores of the film would deteriorate the corrosion resistance. When the heat treatment temperature is reduced while keeping the adhesion and the density of the film, it could possibly give the enhanced corrosion resistance. In this respect, inorganic protective silica film was tried on the surface of stainless steel using a sol-gel chemical route where silica nanoparticles, tetraethoxysilane (TEOS) and methyltriethoxysilane (MTES) were used. Silica nanoparticles with different sizes were mixed and then the film was deposited on the stainless steel substrate. It was intended by mixing the small and the large particles at the same time a sufficient consolidation of the film is possible because of the high surface activity of the small nanoparticles and a modest silica film is obtained with a low temperature heat treatment at as low as $200^{\circ}C$. The prepared film showed enhanced adhesion when compared with a silica film without nanoparticle addition. The films also showed improved protect ability against corrosion.