• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.327-333
• /
• 2001

DLC films due to their extreme properties have attracted a lot of attention. In this study, the films were prepared on High Speed Steel (SKH2) by microwave plasma assisted CVD method using CH4. Every friction test under the normal load 2,5N and sliding velocity of 20,25mm/s in high vacuum (5${\times}$10$\^$-5/ Torr). The films were analyzed with Raman spectroscopy. The films failed immediately in vacuum due to high friction. Wear volume of DLC coated disks decreased more than that of non-DLC coated disks. Also, hardness of the films is about 600HV.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.4
• /
• pp.65-70
• /
• 2006

Carbon nanotubes (CNT) grown by chemical vapor deposition (CVD) and plasma enhanced chemical vapor deposition (PECVD), and followed by annealing at $400{\sim}500^{\circ}C$ were investigated for gas sensing under 1.5ppm $NO_{2}$ concentration at an operating temperature of $200^{\circ}C$. The electrical resistance of CNT sensor decreased with temperature, indicating a semiconductor type. The resistance of CNT sensor decreased with $NO_{2}$ adsorption. It was found that the sensitivity of sensor was affected by humidity and decreased under microwave irradiation for 3 minutes. The CNT sensor grown by PECVD had a higher sensitivity than that of CVD.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.6
• /
• pp.501-506
• /
• 2006

Carbon nanotubes (CNTs) were grown with a microwave plasma enhanced chemical vapor deposition (MPECVD) method, which has been regarded as one of the most promising candidates for the synthesis of CNTs due to the vertical alignment, the low temperature and the large area growth. MPECVD used methane ($CH_4$) and hydrogen ($H_2$) gas for the growth of CNTs. 10 nm thick Ni catalytic layer were deposited on the Ti coated Si substrate by RF magnetron sputtering method. In this work, the pretreatment was that the Ni catalytic layer in different microwave power (600, 700, and 800 W). After that, CNTs deposited on different pressures (8, 12, 16, and 24 Torr) and grown same microwave power (800 W). SEM (Scanning electron microscopy) images showed Ni catalytic layer diameter and density variations were dependent with their pretreatment conditions. Raman spectroscopy of CNTs shows that $I_D/I_G$ ratios and G-peak positions vary with pretreatment conditions.

• Journal of the Korean Vacuum Society
• /
• v.18 no.3
• /
• pp.229-235
• /
• 2009

Millimeter-scale aligned arrays of thin-multiwalled carbon nanotube (t-MWCNT) on layered Si substrates have been synthesized by oxygen-assisted microwave plasma chemical vapor deposition (MPCVD). We have succeeded in growth of vertically aligned MWCNTs up to 2.7 mm in height for 150 min. The effect of $O_2$ and water vapour on growth rate was systematically investigated. In the case of $O_2$ gas, the growth rate was ${\sim}22{\mu}m/min$, which is outstanding growth rate comparing with those of conventional thermal CVD (TCVD). Scanning electron microscope (SEM), energy-dispersive spectroscopy (EDS), and Raman spectroscopy were used to analyze the CNT morphology, composition and growth mechanism. The role of $O_2$ gas during the CNT growth was discussed on.

• Journal of the Korean Society for Heat Treatment
• /
• v.21 no.5
• /
• pp.235-243
• /
• 2008

Ni-C composite films were prepared using a combination of microwave plasma CVD and ion beam sputtering deposition working in a codeposition way. The structure of these films was characterized by energy-dispersive X-ray diffraction (EDXRD), transmission electron microscopy (TEM) and Raman spectroscopy. It was found that a nickel carbide phase, $Ni_3C$ (hcp), formed as very fine crystallites over a wide temperature range when Ni-C films were deposited at low $CH_4$ flow rates. The thermal stability of this nonequilibrium carbide $Ni_3C$ was also studied. As a result, the $Ni_3C$ carbide was found to decompose into nickel and graphite at around $400^{\circ}C$. With high $CH_4$ flow rates (> 0.2 sccm), the structure of the Ni-C films became amorphous. The formation behavior of the carbide and amorphous Ni-C phases are discussed in relation to the electrical resistivity of the films.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.5
• /
• pp.549-555
• /
• 1996

Diamond Like Carbon film is amorphous film which is considered to consist of three coordinate graphite structure and tetrahedron coordinate diamond structure. Its hardness, thermal conductivity and chemical stability are nearly to one of diamond. It is well known to become semi-conductor by doping of inpurity. In this study Diamond Like Carbon film was synthesized by Microwave Plasma CVD in the gas mixture of hydrogen-methan-nitrogen and doped of nitrogen on the single-crystal silicon or silica glass. The temperature of substrate and nitrogen concentration in the gas mixture had an effect on the bonding state, structural properties and conduction mechanism. The surface morphology was observed by Scanning Electron Microscope. The strucure was analyzed by laser Raman spectrometry. The bonding state was evaluated by electron spectroscopy. Diamond Like Carbon film synthesized was amorphous carbon containing the $sp^2$ and $sp^3$ carbon cluster. The number of $sp^2$ bonding increased as nitrogen concentration increased from 0 to 40 vol% in the feed gas at 1233K substrate temperature and at $7.4\times10^3$ Pa. Increase of nitrogen concentration made Diamond Like Carbon to be amorphous and the doze of nitragen could be controlled by nitrogen concentration of feed gas.

• Journal of the Korean Ceramic Society
• /
• v.27 no.4
• /
• pp.513-520
• /
• 1990

Diamond film was deposited on Si wafer substrate from a gas mixture of methane, hydrogen and oxygen by microwave plasma-assisted chemical vapor deposition. The effects of the pre-treatments of the substrate and of the oxygen addition on the diamond film synthesis are described. In order to obtain diamond film, the substrate was pre-treated with 3 kinds of methods. When the substrate was ultrasonically vibrated within the ethyl alcohol dispersed with 25${\mu}{\textrm}{m}$ diamond powder, the denset diamond film was deposited. Addition of oxygen in the gas mixture of methane and hydrogen improved the crystallinity of the deposited diamond film and also increased the deposition rate of the diamond film more than two times.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.289-292
• /
• 1998

The methastable state diamond films have been deposited on Si substrates using MWPCVD. Effects of each experimental parameters of MWPCVD including CH$_4$ concentrations, Oxygen additions, Operating pressure, deposition time, etc. on the growth rate and crystallinity were investigated. The best crystallinity of the finn at 3% methane concentration addition of oxygen to the CH$_4$-$H_2O$ mixture gave an improved film crystallinity at 50% oxygen concentration. Upon increasing the operating pressure and time, the growth rate and crystallinity were increased simultaneously.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.6
• /
• pp.983-989
• /
• 2012

The purpose of this paper is to decide the optimum synthesis conditions of polycrystalline diamond films according to the ratio of gas mixture. Diamond films were deposited with cyclo-hexane as a carbon precursor by the microwave plasma enhanced chemical vapor deposition process. The optimum oxygen ratio to cyclo-hexane was reached about 125 % under the fixed 0.3% c-hexane in hydrogen. Oxygen plays a role in etching the graphitic components of carbon sp2 bond effectively. By OES measurement, the best synthesis conditions found out about 12.5 % and 15.75 %, which is the emission intensity ratios of CH(B-X) and $H{\beta}$ on $H{\alpha}$, respectively. Also, the electron temperature was similar about 5,000 to 5,200 K in this work.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.373-376
• /
• 1997

Diamond thin films were deposited on P-type(100) Si wafers using MPECVD. Prior to deposition, mechanical scretching was done to improve density of nucleation sites with diamond paste of 0.25${\mu}{\textrm}{m}$ size. Diamond films were deposited under the following conditions : methane concentration of 0.5~5%, oxygen concentration of 0~70%, process pressure of 70Torr, process temperature of 900~95$0^{\circ}C$, and deposition time 5hrs. The changes of the morphology and the growth rates of the deposits with the experimental conditions are expriend by Scanning Electron Microscopy. Raman Spectroscopy and X-ray Diffraction method.