• Applied Chemistry for Engineering
• /
• v.30 no.1
• /
• pp.23-28
• /
• 2019

We report a supercapacitor cable, which consists of three-dimensional (3D) porous graphene coated onto the surface of carbon thread. The 3D porous framework of graphene was constructed by microwave-activated process using a graphene oxide-coated carbon thread. The use of microwave irradiation enabled to convert graphene oxide into reduced graphene oxide without any reducing agents and activate graphene sheets into exfoliated and porous graphene sheets. Combining two wire electrodes with a polymer gel electrolyte successfully completed supercapacitor device in a form of cable construction. The supercapacitor cables were highly flexible, and thus can be transformed into various shapes of devices and be integrated into textile items. A high area-capacitance of 38.1 mF/cm was obtained at a scan rate of 10 mV/s. This capacitance was retained 88% of its original value at 500 mV/s. The cycle life was also demonstrated by repeating a charge/discharge process during 10,000 cycles even under bent states, showing a high capacitance retention of 96.5%.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.327-330
• /
• 1998

A 2watts MMIC(Monolithic Microwave Integrated Circuits) SSPA(Solid State Power Amplifiers) for 20GHz band communication systems has been designed, manufactured and measured. The 0.15um pHEMT technologywith the gate size of 400um for single device was used for the fabrication of MMIC Power Amplifier chips. The precision MIC patterns for the peripherals like power combiner/divider and microstrip lines were realized using hard substrate for gold wire/ribbon bonding. The measured data shows that this MMIC SSPA has the linear gain of 18dB, output power of 33.42dBm(2.2Watts)at 20~21GHz.

• 한국전자현미경학회:학술대회논문집
• /
• 2004.11a
• /
• pp.23-34
• /
• 2004

• 전기의세계
• /
• v.19 no.6
• /
• pp.8-12
• /
• 1970

A Device is described which intensity modulates a light beam at modulating frequency in the M/W region. A Method of designing a practical crystalline microwave-Freg. light modulator has been described. In addition, Electrooptic properties and operation as light modulator of NH$_{4}$H$_{2}$po$_{4}$ is described. A light path is provided through the crystal into a suitably oriented analyzer. The intensity of the light beam emerging from the latter varies at the same rate as the cavity frequency.

• Korean Journal of Optics and Photonics
• /
• v.16 no.5
• /
• pp.469-475
• /
• 2005

An integrated photonic microwave bandpass filter has been proposed and demonstrated incorporating a coherently coupled microring resonator in low-loss polymers. The proposed device may feature compact site, simple structure, tuning via the thermooptic and electrooptic effect, and flexible integration with other electrical and optical devices. The resonator was designed to have an extremely small bandwidth so that it could be used to selectively pass the optical signal carrying the microwave signal to attain efficient bandpass filtering. We made and tested two resonators with a single ring and double rings, and performed a theoretical fitting of their measured transfer curves to predict the performance of the microwave filters based on them precisely. It was found that as the number of the rings used for the resonator increases, the bandwidth gets smaller, the rolloff sharper, and the band rejection higher. Finally our filter exhibited the center frequency of 10GHz, the 3-dB bandwidth of 1.0GHz, the corresponding quality (Q) factor of 10, and the rejection outside of the passband of more than 25dB.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.50-51
• /
• 2009

This paper presents integrated passive device (IPD) based on Wilkinson power divider. The simulated 2-way power divider has the insertion loss of 3.123 dB, output isolation of -24.576 dB, input return loss of 26.415 dB, and output return loss of 33.478 dB. The power divider is based on IPD process design simulation at 2.5 GHz for WiMAX (Worldwide Interoperability for Microwave Access) applications. The chip size of power divider is $1\;\times\;1.2\;mm^2$, which is under fabrication.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.342-344
• /
• 2009

From a hydrodynamic device simulation for the pseudomorphic high electron mobility transistors (pHEMTs), we observe an increase of maximum extrinsic transconductance and a decrease of source-drain capacitances. This gives rise to an enhancement of the switching speed and isolation characteristics as the upper-to-lower planar-doping ratios (UTLPDR) increase. On the basis of simulation results, we fabricate single-pole-double-throw transmitter/receiver monolithic microwave integrated circuit (MMIC) switches with the pHEMTs of two different UTLPDRs (4:1 and 1:2). The MMIC switch with a 4:1 UTLPDR shows about 2.9 dB higher isolation and approximately 2.5 times faster switching speed than those with a 1:2 UTLPDR.

• Journal of Magnetics
• /
• v.22 no.2
• /
• pp.275-280
• /
• 2017

A magnetic-field tunable 2.4 GHz microwave bandpass filter having insertion loss < -5dB on an FR4 substrate with the flaky magnetic material was designed and characterized. The tunability in the designed bandpass filter was achieved by adhering soft magnetic materials on top of the device. This soft magnetic material can be composed of ferromagnetic substance or ferrimagnetic substance. The performance of the designed bandpass filter under its influence is investigated. The frequency offset ratio changes over 30 %. There is over 20 % change in the center frequency towards the lower frequency region due to this application. These magnetic material layers achieved the center frequency shift and bandwidth extension without actually changing the original structure of the device.

• Korean Journal of Materials Research
• /
• v.7 no.5
• /
• pp.431-433
• /
• 1997

We investigated a double ring resonator(DRR)device to improve the resonating Q value of a superconductor resonator. To make a DRR device, we made a large area YBCO film on a MgO substrate by pulsed laser deposition(PLD). Thetransition temperature was 88 K and the film was uniformly deposited. We also deposited 500$\AA$SrTiO$_{3}$on the YBCO thin film to protect the superconducting properties from degradation. The loaded Q value was measured as 50000 from simulation and as 2000 from experiment near 10GHz at 77K.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1078-1080
• /
• 2003

This paper proposes the boost input type resonant power supply for driving the magnetron device of the high-capacity microwave oven. Circuit topology of the proposed power supply is the boost input type resonant converter which uses the resonance between transformer leakage inductance and resonance capacitance. Proposed power supply obtains high power factor more than 98% through continuous current mode pulse width modulation. To verify the validity of the proposed power supply, operation principle in the steady state is analyzed and experimental results are presented.