• Journal of Powder Materials
• /
• v.28 no.2
• /
• pp.103-109
• /
• 2021

High-entropy alloys have excellent mechanical properties under extreme environments, rendering them promising candidates for next-generation structural materials. It is desirable to develop non-equiatomic high-entropy alloys that do not require many expensive or heavy elements, contrary to the requirements of typical high-entropy alloys. In this study, a non-equiatomic high-entropy alloy powder Fe_49.5Mn₃₀Co₁₀Cr₁₀C_0.5 (at.%) is prepared by high energy ball milling and fabricated by spark plasma sintering. By combining different ball milling times and ball-to-powder ratios, we attempt to find a proper mechanical alloying condition to achieve improved mechanical properties. The milled powder and sintered specimens are examined using X-ray diffraction to investigate the progress of mechanical alloying and microstructural changes. A miniature tensile specimen after sintering is used to investigate the mechanical properties. Furthermore, quantitative analysis of the microstructure is performed using electron backscatter diffraction.

• Journal of Powder Materials
• /
• v.28 no.4
• /
• pp.336-341
• /
• 2021

In this study, a nanocrystalline FeNiCrMoMnSiC alloy was fabricated, and its austenite stability, microstructure, and mechanical properties were investigated. A sintered FeNiCrMoMnSiC alloy sample with nanosized crystal was obtained by high-energy ball milling and spark plasma sintering. The sintering behavior was investigated by measuring the displacement according to the temperature of the sintered body. Through microstructural analysis, it was confirmed that a compact sintered body with few pores was produced, and cementite was formed. The stability of the austenite phase in the sintered samples was evaluated by X-ray diffraction analysis and electron backscatter diffraction. Results revealed a measured value of 51.6% and that the alloy had seven times more austenite stability than AISI 4340 wrought steel. The hardness of the sintered alloy was 60.4 HRC, which was up to 2.4 times higher than that of wrought steel.

• Journal of Powder Materials
• /
• v.28 no.3
• /
• pp.221-226
• /
• 2021

We fabricate the non-equiatomic high-entropy alloy (NE-HEA) Fe_49.5Mn₃₀Co₁₀Cr₁₀C_0.5 (at.%) using spark plasma sintering under various sintering conditions. Each elemental pure powder is milled by high-energy ball milling to prepare NE-HEA powder. The microstructure and mechanical properties of the sintered samples are investigated using various methods. We use the X-ray diffraction (XRD) method to investigate the microstructural characteristics. Quantitative phase analysis is performed by direct comparison of the XRD results. A tensile test is used to compare the mechanical properties of small samples. Next, electron backscatter diffraction analysis is performed to analyze the phase fraction, and the results are compared to those of XRD analysis. By combining different sintering durations and temperature conditions, we attempt to identify suitable spark plasma sintering conditions that yield mechanical properties comparable with previously reported values. The samples sintered at 900 and 1000℃ with no holding time have a tensile strength of over 1000 MPa.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.25 no.6
• /
• pp.580-585
• /
• 2022

In this study, the high-temperature dielectric constant of Si₃N₄ ceramics, a representative non-oxide-based radome material, was evaluated and the cause of the dielectric constant change was analyzed in relation to the oxidation behavior. The dielectric constant of Si₃N₄ ceramics was 7.79 at room temperature, and it linearly increased as the temperature increased, showing 8.42 at 1,000 ℃. As results of analyzing the microstructure and phase for the Si₃N₄ ceramics before and after heat-treatment, it was confirmed that oxidation did not occur at all or occurred only on the surface at a very insignificant level below 1,000 ℃. Based on this, it is concluded that the increase in the dielectric constant according to the temperature increase of Si₃N₄ ceramics is irrelevant to the oxidation behavior and is only due to the activation of charge polarization.

• Journal of the Korea Concrete Institute
• /
• v.25 no.1
• /
• pp.3-9
• /
• 2013

In ultra high strength concrete, when electric arc furnace oxidizing slag is substituted for sea sand as fine aggregate, compressive strength was improved about 15 MPa. To figure out the cause of the improvement in compressive strength, this study considered the dissolution characteristics of Ca component in fine aggregate and examined the microstructure, porosity, microhardness, and Ca/Si mole ratio on the interface of fine aggregate and paste. And to examine the mechanism of strength improvement resulted from the shape of fine aggregate, this study measured the surface roughness of fine aggregate with AFM. According to the result of this experiment, the mechanisms of strength improvement in ultra high strength concrete resulted from the use of electric arc furnace oxidizing slag as fine aggregate can be divided into chemical and physical mechanisms. In the chemical mechanism, the soluble Ca component contained in electric arc furnace oxidizing slag is dissolved and forms a hydrate between fine aggregate and paste to improve the interlocking strength of fine aggregate-paste. Also, it makes the microstructure around the fine aggregate. And in the physical mechanism, electric arc furnace oxidizing slag has a twice greater surface roughness than sea sand, so the interlocking strength between fine aggregate and paste increases, which contributes to the development of compressive strength.

• Journal of the Korean Ceramic Society
• /
• v.50 no.1
• /
• pp.37-42
• /
• 2013

Tristructural-isotropic (TRISO)-coated particles were fabricated by a fluidized-bed chemical vapor deposition (FBCVD) method for use in a very high temperature gas-cooled reactor (VHTR). ZrC as a constituent layer of TRISO coating layers was deposited by a chloride process using $ZrCl_4$ and $CH_4$ source gases in a temperature range of $1400^{\circ}C$ and $1550^{\circ}C$. The change in the microstructure of ZrC depending on the deposition temperature and its effect on the hardness were evaluated. As the deposition temperature increased to $1500^{\circ}C$, the grain size of the ZrC increased and the hardness of the ZrC decreased according to the Hall-Petch relationship. However, at $1550^{\circ}C$, the ZrC layer was highly non-stoichiometric and carbon-rich and did not obey the Hall-Petch relationship in spite of the decrease of the grain size. A considerable amount of pyrolytic carbon at the grain boundaries of the ZrC as well as coarse granular pyrolytic carbon were locally distributed in the ZrC layer deposited at $1550^{\circ}C$. Therefore, the hardness decreased largely due to the formation of a large amount of pyrolytic carbon in the ZrC layer.

• Journal of Powder Materials
• /
• v.23 no.5
• /
• pp.379-383
• /
• 2016

A thick film of $Li_7La_3Zr_2O_{12}$ (LLZO) solid-state electrolyte is fabricated using the tape casting process and is compared to a bulk specimen in terms of the density, microstructure, and ion conductivity. The final thickness of LLZO film after sintering is $240{\mu}m$ which is stacked up with four sheets of LLZO green films including polymeric binders. The relative density of the LLZO film is 83%, which is almost the same as that of the bulk specimen. The ion conductivity of a LLZO thick film is $2.81{\times}10^{-4}S/cm$, which is also similar to that of the bulk specimen, $2.54{\times}10^{-4}S/cm$. However, the microstructure shows a large difference in the grain size between the thick film and the bulk specimen. Although the grain boundary area is different between the thick film and the bulk specimen, the fact that both the ion conductivities are very similar means that no secondary phase exists at the grain boundary, which is thought to originate from nonstoichiometry or contamination.

• KIEAE Journal
• /
• v.15 no.4
• /
• pp.45-52
• /
• 2015

Purpose: Foam concrete is the concrete that contains large amount of air voids inside. In general, the density of foam concrete depends on parameters like water/binder ratio, foam volume, aggregate and pozzolan content, etc. Method: In this study, the effect of foam volume and fly ash content on dry density is investigated intensively in order to find the relationship between each parameter and their abilities to counteract with each other. According to the above information, though there are quite a number of studies on the effect micro fiber on foam concrete at low volume fractions, there is still lack of information especially on the high fiber content side. The objective of the second study is to investigate further on the use of micro fiber at higher volume fraction and fill in the lacking information. Beside from this study, the investigation of the effect of micro-fiber (polypropylene) to enhance the properties of foam concrete is also carried out. Result: Of the two variables that are investigated in this study, the foam volume and the fly ash content, show significant effect on the properties of foam concrete. The foam volume tends to decrease the density and strength of foam concrete. In the second part of our study, a large fibre volume fraction is proved to be able to evidently increase the flexural strength of foam concrete up to about 40% due to the effect of fibre bridging over the crack and a significant number of fibres that intercepts the crack surfaces. However, the compressive strength is found to decrease severely due to the occurrence of large pores as the result of fibre being added into concrete mixture.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.705-709
• /
• 2003

The microstructure and electrical properties of the $Pr_6O_{11}$-based ZnO varistor ceramics, which are composed of Zn-Pr-Co-Cr-Tb oxides, were investigated with $Tb_4O_7$ amount. The varistor ceramics exhibited very high densification based on increasing density in the range of $5.73{\sim}5.85g/cm^3$ as $Tb_4O_7$ amount is increased. The calculated nonlinear exponent( ${\alpha}$ ) in varistor ceramics without $Tb_4O_7$ was only 8.9, whereas the ${\alpha}$ value of the varistor ceramics with $Tb_4O_7$ was abruptly increased in the range of 18.6 to 42.0. In particular, the maximum value(42.0) of ${\alpha}$ was obtained by doping of 1.0 mol% $Tb_4O_7$. The measured leakage current($I_{\ell}$) in varistor ceramics without $Tb_4O_7$ was $40.1{\mu}A$, whereas the $I{\ell}$ value of the varistors with $Tb_4O_7$ was very abruptly decreased below $5{\mu}A$. It is estimated that $Tb_4O_7$ additives will is applied usefully in development of varistors possessing high performance.

• Progress in Superconductivity
• /
• v.7 no.1
• /
• pp.58-63
• /
• 2005

We investigated the surface oxidation behavior of cube-textured polycrystalline nickel at various oxidation conditions. Cube-textured NiO film was formed on a cube-textured polycrystalline nickel regardless of oxidation conditions but different growth behavior of NiO crystals was observed depending on the oxidation conditions. The introduction of water vapor into $O_2$ did not affect the texture evolution, but rough and porous microstructure was developed. Microstructure of NiO film tends to be denser as the oxygen partial pressure increases. It is interesting that (111) peak of theta - two theta diffraction pattern started to get stronger in air atmosphere and (111) plane became the major texture in the substrate oxidized in high purity argon gas. Small amount of high index crystallographic plane NiO peak crystal was observed when $N_{2}O$ was used as an oxidant while only (200) plane crystal was formed in dry $O_2$ atmosphere. Flat and smooth surface was changed into rough faceted one when ramping rate to oxidation temperature was faster. The grain size of NiO was decreased when the oxygen partial pressure was low. It was also observed that the modification of nickel surface suppressed the development of (200) texture.