• International Journal of Korean Welding Society
• /
• v.3 no.1
• /
• pp.23-28
• /
• 2003

The effect of the welding speeds on the weld bead shape, microstructure, and mechanical properties in type 304 austenitic stainless steels was investigated by microscopic test, Erichsen test and tensile test. In this study welds were produced using autogeneous Direct Current Straight Polarity (DCSP) and pulsed current GTA welding. This study shows the ferrite content, ductility, tensile strength and elongation of high speed welds are decreased with increasing welding speed. The high speed welds exhibits satisfactory tensile strength, though the ductility is not good as that of the base metal.

• Journal of the Korean Ceramic Society
• /
• v.54 no.1
• /
• pp.33-37
• /
• 2017

Single phase niobium nitride (NbN) coatings were deposited using asymmetric bipolar pulsed dc sputtering by varying pulse frequency and duty cycle of pulsed plasmas. Crystal structure, microstructure, morphology and mechanical properties were examined using XRD, FE-SEM, AFM and nanoindentation. Upon increasing pulse frequencies and decreasing duty cycles, the coating morphology was changed from a pyramidal-shaped columnar structure to a round-shaped dense structure with finer grains. Asymmetric bipolar pulsed dc sputtered NbN coatings deposited at pulse frequency of 25 kHz is characterized by higher hardness up to 17.4 GPa, elastic modulus up to 193.9 GPa, residual compressive stress and a smaller grain size down to 27.5 nm compared with dc sputtered NbN coatings at pulse frequency of 0 kHz. The results suggest that the asymmetric bipolar pulsed dc sputtering technique is very beneficial to reactive deposition of transition-metal nitrides such as NbN coatings.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1118-1122
• /
• 2006

In this study, in order to develop the low temperature sintering multilayer piezoelectric actuator, PMN-PNN-PZT system ceramics were manufactured and their microstructure, ferroelectric and piezoelectric properties were investigated. By increasing sintering temperature, remanent polarization$(P_r)$ was increased due to the increase of sinterability and grain size. However, coercive $field(E_c)$ showed an opposite tendency to remanent polarization owing to the feasibility of domain wall motion. At the sintering temperature of $900^{\circ}C$, dielectric $constant({\varepsilon}_r)$, electromechanical coupling $factor(k_p)$, piezoelectric $constant(d_{33})$ and mechanical quality $factor(Q_m)$ showed the optimal value of 1095, 0.60, 363 and 1055, respectively, for multilayer piezoelectric actuator application.

• Journal of Korea Foundry Society
• /
• v.15 no.6
• /
• pp.546-557
• /
• 1995

This study was undertaken to obtain an improved understanding of the effects of alloying elements on the residual amounts of Mg in the melt and on the resultant microstructure of compacted vermicular graphite cast irons, and the influence of alloying elements and cooling rates during solidification on the formation of phosphide eutectics, and on the mechanical properties of compacted vermicular graphite cast irons containing copper, tin, molybdenum for producing pearlitic matrix, and also containing phosphorus and boron for increasing wear resistance were evaluated.

• Journal of the Korean institute of surface engineering
• /
• v.57 no.4
• /
• pp.348-354
• /
• 2024

Nanocrystalline zirconium nitride (ZrN) coatings were deposited by mid-frequency direct current sputtering (mfMS) with varying pulsed plasma parameters such as pulse frequency and duty cycle to understand the effect of pulsed plasma on the microstructure, residual stress and mechanical properties. The results show that, with the increasing pulse frequency and decreasing duty cycle, the coating morphology changed from a porous columnar to a dense structure, with finer grains. Mid-frequency magnetron sputtered ZrN coatings with pulse frequency of 30 kHz showed the highest both nanoindentation hardness of 16.3 GPa, and elastic modulus of 214.4 GPa. In addition, Effect of pulse frequency on a residual stress and average crystal grain sizes was also investigated.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.89-92
• /
• 2009

As a class of materials, Ni-base superalloys are among the most difficult metal alloys to forge together with refractory metals and cobalt-base superalloys. The mechanical properties of Ni-base superalloys depend very much on grain size and the strengthening phases, $\gamma$' ($Ni_3$(Al,Ti)-type) and $\gamma$".($Ni_3$Nb-type). Especially, the control of grain size remains as a sole means for the control of mechanical properties. The grain size and distribution changes of the wrought superalloys during hot working and heat treatment are mainly controlled by the recrystallization and grain growth behaviors. In this presentation, prediction technology of grain size through the computer-aided process design, and numerical modeling for predicting the microstructure evolution of Ni-base superalloy during hot working were introduced. Also, some case studies were dealt with actual forming processes of Ni-base superalloys.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.964-965
• /
• 2006

The injection molded Fe sintered bodies were fabricated using two kinds of nano Fe powders, $Fe-5%vol.ZrO_2$ and $Fe-10vol.%ZrO_2$ powders. The relationship between microstructure and mechanical properties depending on the $ZrO_2$ contents and sintering temperature were characterized by SEM and TEM techniques. In the wear test, the $Fe-0vol%ZrO_2$ sintered bodies showed mainly adhesive wear, but in the Fe-5%vol. $ZrO_2$ and Fe-10vol. % $ZrO_2$ composites the main wear behavior showed abrasive wear mode.

• Korean Journal of Materials Research
• /
• v.15 no.9
• /
• pp.608-612
• /
• 2005

Microstructure and mechanical properties of fibrous $A1_2O_3-(m-ZrO_2)/t-ZrO_2$ composite were investigated depending on the dimensional array. By the change of stacking arrangement of fibrous filaments, 2 and 3-dimensional fibrous composites were successfully obtained without bulk defects such as shrinkage cavity and cracks. The maximum mechanical properties were achieved In the 3-dimensional array composite, due to the fine fibrous and dense microstructure control, in which the values of vickers hardness, fracture toughness and bending strength were about 1507 Hv, $7.2MPa{\cdot}m^{1/2}$ and 650 MPa, respectively.

• Journal of Powder Materials
• /
• v.11 no.3
• /
• pp.259-264
• /
• 2004

Aluminum based metal matrix composite reinforced with SiC particles was fabricated by the powder-in sheath rolling method. A stainless steel tube with outer diameter of 12 mm and wall thickness of 1mm was used as a sheath. Mixture of aluminum powder and SiC particles of which volume content was varied from 5 to 20vol.% was filled in the tube by tap filling and then rolled to 75% reduction at ambient temperature. The rolled specimen was sintered at 56$0^{\circ}C$ for 0.5hr. The tensile strength of the (SiC)$_{p}$/Al composite increased with the volume content of SiC particles, and at 20vol.% it reached a maximum of 100㎫ which is 1.6 times higher than unreinforced material. The elongation decreased with the volume content of $Al_{2}$O$_{3}$ particles. The mechanical properties of the (SiC)$_{p}$/Al composite fabricated by the powder-in sheath rolling is compared with that of (Al$_{2}$O$_{3}$)$_{p}$/Al composite by the same process.ess.

• Transactions of Materials Processing
• /
• v.33 no.1
• /
• pp.36-42
• /
• 2024

Additive manufacturing with 3XX austenitic stainless steels has been widely investigated during a decade due to its high strength, good corrosion resistance, and fair weldability. However, in recently, Ni price drastically increased due to the high demand of secondary battery for electric mobilities. Thus, it is essential to substitute the Ni with Mn for reducing stainless steels price. Meanwhile, the chemical composition changes in stainless steels not only affect to its properties but also change the optimal processing parameters during additive manufacturing. Therefore, it is necessary to optimize the processing parameters of each alloy for obtaining high-quality product using additive manufacturing. After processing optimization, mechanical properties and microstructure of the laser-powder bed fusion processed Fe-15Cr-7Ni-3Mn alloy were investigated in both room (298 K) and cryogenic (77 K) temperatures. Since the temperature reduction affects to the deformation mechanism transition, multi-scale microstructural characterization technique was conducted to reveal the deformation mechanism of each sample.