• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.120-127
• /
• 2005

The design method of the transversal filter using continuously cascaded directional couplers is presented. The coupler can be treated for a continuously varying nonuniform coupled transmission line. The design method is based on the optimum extraction of desired coupling factor by the control of null positions which are inherent to the coupling spectra pattern. In the optimization process, the improved Woodward-Lawson sampling method is applied to easily synthesize the distributed delay and weighting elements for transversal filter properties. For application, the microstrip transversal filter is fabricated and optimum dielectric overlay is introduced for the mode phase velocity compensation for non-TEM coupler nodes by using SDA(Spectral Domain Approach). Experiment results confirm the validity of the proposed method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.12
• /
• pp.1335-1340
• /
• 2003

In this paper, a single balanced diode Mixer for the homodyne FMCW radar to detect distance and velocity of a vehicle target is designed and implemented using a microstrip line and two schottky barrier beam lead diodes. This mixer is optimally designed to have less a conversion loss within the 100 MHz bandwidth with a little LO injection power and a higher LO isolation as soon as possible through the embedded electrical length of microsrtrip line placed between the coupler and diode matching, considering together LO matching condition. The measured results show 6 dB of conversion loss, 23 dB LO/RF isolation and 3 dBm of input 1l dB, respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.6 s.348
• /
• pp.46-52
• /
• 2006

We report on a high performance 94 GHz MMIC resistive mixer using 70-nm metamorphic high electron mobility transistor (MHEMT) and micro-machined W-band ring coupler. A novel 3-dimensional structure of resistive mixer was proposed in this work, and the ring coupler with the surface micro-machined dielectric-supported air-gap microstrip line (DAMLs) structure was used for high LO-RF isolation. The fabricated mixer showed an excellent LO-RF isolation of -29.3 dB and a low conversion loss of 8.9 dB at 94 GHz. To our knowledge, compared to previously reported W-band mixers, the proposed MHEMT-based resistive mixer using micro-machined ring coupler has shown superior LO-RF isolation as well as similar conversion loss.

• Journal of information and communication convergence engineering
• /
• v.1 no.3
• /
• pp.139-142
• /
• 2003

In this paper, we consider the factors that affect a conversion loss performance in designing a single balanced diode mixer integrated with IRF(Image Reject Filter), based on the embedded electrical wavelength placed between the IRF and mixer, diode matching and LO drive amplifier. To evaluate the conversion loss performance, we suggest two types of a single balanced mixer using 90 degree branch line coupler, microstrip line and schottky diode. One is only mixer and the other is integrated with IRF and LO drive amplifier. The measured results of a single balance diode mixer integrated IRF show the conversion loss of 8.5 dB and the flatness of 1 dB p-p from 21.2 GHz to 22.6 GHz with 10 dBm LO. The measured input PI dB and IIP3 are 7 dBm and 15 dBm respectively under the nominal LO power level of 10dBm. The LO/RF and LO/IF isolation are 22 dB and 50 dB, respectively.

• Proceedings of the IEEK Conference
• /
• 2004.06a
• /
• pp.159-162
• /
• 2004

In this paper, we introduce the concept of ICTL(inductively compact transmission line) that is new type of compact transmission line. As using the ICTL, the compact microstrip hybrid rat-race coupler was designed. It's new type compact rat-race couplers. The designed compact rat-race cooper at 1.8 GHz has area of 1182 $mm^2$, and it is $58\%$ for conventional rat-race couplers. Measured results are agree with predicted results.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.2
• /
• pp.257-260
• /
• 2014

In this paper, a high gain waveguide array antenna combining horn antenna on slot radiator was designed. And the fabricated antenna showed enough gain, improved efficiency and broadband characteristics for receiving satellite signals, compare to conventional microstrip antenna which has dielectric loss and radiation loss on transmission line. For easy fabrication, the waveguide structure was composed by 3-stages of radiator, signal coupler and transmission line. By experiment, the array waveguide antenna of 4 by 16 showed 28.3[dBi] gain and 2:1 of VSWR. And by combining horn antenna structure, the gain was increased 1[dB]. The received signal from Koreasat 6 by measurement showed 16[dBc] of C/N on BS(Broadcasting Satellite)-band and 14[dBc] of C/N on CS(Communication Satellite)-band.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.2 no.2
• /
• pp.19-24
• /
• 1991

This paper propose a new taegeuk shaped directional couper and verify the possibility of high power division rate in those directional coupler through the experiments. We took the taegeuk shaped structure in those proposed directional coupler to utilize a $3\lambda/4$ section of hybrid ring directional coupler actively, and calculated the branch admittances, which satisfied the condition of perfect matching and isolation in the center frequency, by even odd mode analyzing methodes. On the result, we knew that it can be realized a much higher power division rate than reported result in same circuit area within the producible resistance limit in the microstrip line, made the taegeuk shaped directional couplers with 0, 8, 16 dB power split ratio in the 10 GHz frequency using CGP - 502 plate, and confirmed the validity of theory through the experiments.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.2
• /
• pp.171-178
• /
• 1998

Generally, the output matching circuit has the most influence to the output power of oscillator and existing method for output matching has difficulty for making the optimum output matching circuit because the matching has to be done nearby the infinite impedance area of the Smith Chart. In this paper, it is studied for the output matching circuit of the microwave oscillator to get the maximum output power. The maximum output point can be found by adjusting the position of moving short in the Tuner while the oscillator is operating after connect the 3-dB coupler Tuner to the oscillator without output matching circuit. To design the oscillator for the maximum output power can be done easily with the microstrip line which is realized from the measured S-parameters of Tuner. In compare the oscillator by the existing method with another one by the suggested method in this paper, the first one has 6.45 dBm output power and second one has 9.71 dBm which is 3.26 dBm higher than the first one at the oscillation frequency 1.0338 GHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2233-2238
• /
• 2013

A novel design method of ultra wideband based on the composite right-/left handed (CRLH) transmission line is presented in this paper. Defected ground structure and microstrip interdigital coupler are used to implement the CRLH transmission line. The proposed CRLH transmission line in this paper have composite characteristics of low pass filter and high pass filter, also it has good advantages of low insertion loss and ultra wide passband characteristics. The structure with different cell number are studied, and the UWB filter using 3-cell CRLH transmission line is fabricated and measured, which shows a good agreement between simulated and measured results. It has center frequency of 5 GHz, fractional bandwidth of 105 %, and insertion loss of 0.7 dB at center frequency.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.66-70
• /
• 2003

In this paper a plannar singly balanced diode Miter for 24GHz band application is designed and implemented using a microstrip line and two schottky barrier beam lead mixer diodes. The implemented mixer have a conversion loss of 6 [dB], LO/RF isolation of 23 [dB], input 1dB compression point of 4 [dBm]. this diode mixer would be useful for homedyne radar.