• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1598-1600
• /
• 2003

Microcrystalline silicon(c-Si:H) thin-film solar cells are prepared with intrinsic Si-layer by hot wire CVD. The operating parameters of solar cells are strongly affected by the filament temperature ($T_f$) during intrinsic layer. Jsc and efficiency abruptly decreases with elevated $T_f$ to $1400^{\circ}C$. This deterioration of solar cell parameters are resulted from increase of crystalline volume fraction and corresponding defect density at high $T_f$ The heater temperature ($T_h$) are also critical parameter that controls device operations. Solar cells prepared at low $T_h$ (<$200^{\circ}C$) shows a similar operating properties with devices prepared at high $T_f$, i.e. low Jsc, Voc and efficiency. The origins for this result, however, are different with that of inferior device performances at high $T_f$. In addition the phase transition of the silicon films occurs at different silane concentration (SC) by varying filament temperature, by which highest efficiency with SC vanes with $T_f$.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.478-478
• /
• 2012

Recently, there are many researches in order to increase the deposition rate (D/R) and improve film uniformity and quality in the deposition of microcrystalline silicon thin film. These two factors are the most important issues in the fabrication of the thin film solar cell, and for the purpose of that, several process conditions, including the large area electrode (more than 1.1 X 1.3 (m2)), higher pressure (1 ~ 10 (Torr)), and very high frequency regime (VHF, 40 ~ 100 (MHz)), have been needed. But, in the case of large-area capacitively coupled discharges (CCP) driven at frequencies higher than the usual RF (13.56 (MHz)) frequency, the standing wave and skin effects should be the critical problems for obtaining the good plasma uniformity, and the ion damage on the thin film layer due to the high voltage between the substrate and the bulk plasma might cause the defects which degrade the film quality. In this study, we will propose the new concept of the large-area multi-electrode (a new multi-electrode concept for the large-area plasma source), which consists of a series of electrodes and grounds arranged by turns. The experimental results with this new electrode showed the processing performances of high D/R (1 ~ 2 (nm/sec)), controllable crystallinity (~70% and controllable), and good uniformity (less than 10%) at the conditions of the relatively high frequency of 40 MHz in the large-area electrode of 280 X 540 mm2. And, we also observed the SEM images of the deposited thin film at the conditions of peeling, normal microcrystalline, and powder formation, and discussed the mechanisms of the crystal formation and voids generation in the film in order to try the enhancement of the film quality compared to the cases of normal VHF capacitive discharges. Also, we will discuss the relation between the processing parameters (including gap length between electrode and substrate, operating pressure) and the processing results (D/R and crystallinity) with the process condition map for ${\mu}c$-Si:H formation at a fixed input power and gas flow rate. Finally, we will discuss the potential of the multi-electrode of the 3.5G-class large-area plasma processing (650 X 550 (mm2) to the possibility of the expansion of the new electrode concept to 8G class large-area plasma processing and the additional issues in order to improve the process efficiency.

• 한국전기전자재료학회논문지
• /
• 제31권5호
• /
• pp.320-323
• /
• 2018

SiGe thin films were deposited by remote plasma enhanced chemical vapor deposition (RPE-CVD) at $400^{\circ}C$ using $SiH_4$ or $SiCl_4$ and $GeCl_4$ as the source of Si and Ge, respectively. The growth rate and the degree of crystallinity of the fabricated films were characterized by scanning electron microscopy and Raman analysis, respectively. The optical and electrical properties of SiGe films fabricated using $SiCl_4$ and $SiH_4$ source were comparatively studied. SiGe films deposited using $SiCl_4$ source showed a lower growth rate and higher crystallinity than those deposited using $SiH_4$ source. Ultraviolet and visible spectroscopy measurement showed that the optical band gap of SiGe is in the range of 0.88~1.22 eV.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 춘계학술대회 논문집
• /
• pp.98-98
• /
• 2009

Hydrogenated nano-, microcrystalline silicon 박막(nc-, ${\mu}c-Si:H$)은 박막 트랜지스터 및 실리콘 박막형 태양전지등에 널리 쓰이고 있다. 이러한 결정화 실리콘 박막을 내장형 안테나를 사용하여 고밀도 플라즈마를 발생시킬 수 있는 장치를 통하여 증착 후 열처리 공정이 없는 방법을 사용하여 박막을 제작하였다. 특히, 증착시 기판에 바이어스를 함께 인가하므로 증착된 박막의 결정화에 미치는 영향에 관한 연구를 하였다. 기판에 인가된 바이어스가 60W일 때 가장 높은 결정화율을 보이는 것을 알 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.230-230
• /
• 2013

In amorphous or microcrystalline thin-film silicon solar cells, p-i-n structure is used instead of p/n junction structure as in wafer-based Si solar cells. Hence, these p-i-n structured solar cells inevitably consist of many interfaces and the cell efficiency critically depends on the effective control of these interfaces. In this study, in-situ plasma treatment process of the interfaces was developed to improve the efficiency of a-Si:H solar cell. The p-i-n cell was deposited using a single-chamber VHF-PECVD system, which was driven by a pulsed-RF generator at 80 MHz. In order to solve the cross-contamination problem of p-i layer, high RF power was applied without supplying SiH4 gas after p-layer deposition, which effectively cleaned B contamination inside chamber wall from p-layer deposition. In addition to the p-i interface control, various interface control techniques such as thin layer of TiO2 deposition to prevent H2 plasma reduction of FTO layer, multiple applications of thin i-layer deposition and H2 plasma treatment, H2 plasma treatment of i-layer prior to n-layer deposition, etc. were developed. In order to reduce the reflection at the air-glass interface, anti-reflective SiO2 coating was also adopted. The initial solar cell efficiency over 11% could be achieved for test cell area of 0.2 $cm^2$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1514-1516
• /
• 1999

This paper covers our efforts to improve the low carrier mobility and light instability of hydrogenated amorphous silicon (a-Si:H) films with microcrystalline silicon $({\mu}c-Si)$ films. We successfully prepared ${\mu}c-Si$ films on $CaF_2$/glass substrate by decomposition of $SiH_4$ in RPCVD system. The $CaF_2$ films on glass served as a seed layer for ${\mu}c-Si$ film growth. The XRD analysis on $CaF_2$/glass illustrated a (111) preferred $CaF_2$ grains with the lattice mismatch less than 5 % of Si. We achieved ${\mu}c-Si$ films with a crystalline volume fraction of 61 %, (111) and (220) crystal orientations. grain size of $706\AA$, activation energy of 0.49 eV, and Photo/dark conductivity ratio of 124. By using a $CaF_2$/glass structure. we were able to achieve an improved ${\mu}c-Si$ films at a low substrate temperature of $300^{\circ}C$.

• 전자통신동향분석
• /
• 제27권5호
• /
• pp.109-125
• /
• 2012

액정 디스플레이의 산업 규모는 놀라운 속도로 확대되고 있다. 그 원동력이 된 것이 박막 트랜지스터(Thin Film Transistor: TFT) 기술의 발전에 있다. 비정질 실리콘(Amorphous Silicon: a-Si) TFT 기술은 대형 액정 TV를 탄생시키고, 저온 폴리실리콘 TFT는 휴대전화 등의 중소형 디스플레이와 AMOLED의 핵심 기술이 되었다. 또한 다양한 TFT 기술 seeds가 계속해서 출현하여 정보 인프라와 생활 스타일에 맞춘 새로운 정보기기의 출현을 예감시키고 있다. 새로운 응용제품의 요구는 새로운 기술 개발의 견인차가 되고 있다. 최근에는 이러한 요구에 따라 산화물 TFT, 마이크로 결정실리콘(microcrystalline Si: ${\mu}c-Si$) TFT, 유기물 TFT 등의 기술도 활발하게 연구개발되고 있다. 본고에서는 지금까지의 TFT 기술 개발의 발전사를 뒤돌아보고 지금부터의 발전 방향을 박막 트래지스터 기술 이노베이션 관점으로부터 전망하였다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 추계학술발표강연 및 논문개요집
• /
• pp.66-66
• /
• 2003

실리콘 박막 태양전지는 저가, 대면적 생산이 가능해 최근 주택용, 발전용의 차세대 태양전지로써 부각되고 있다. 그러나, 단결정, 다결정 태양전지에 비해 상대적으로 낮은 효율특성 때문에 그 특성을 향상시키고자 하는 다양한 연구가 진행되고 있다. 비정질/마이크로결정질 실리콘 박막 태양전지에서 광흡수층으로 사용되는 i층은 광흡수를 최대화하기 위해 암전류($\sigma$$_{d}$)가 낮고 광전류($\sigma$$_{ph}$ )가 높은, 즉, 광민감도($\sigma$$_{ph}$ /$\sigma$$_{d}$)가 높은 박막을 적용해야 한다. 한편, 도핑된 윈도우층의 경우에는 넓은 밴드갭을 갖도록 하여 윈도우층에서의 광흡수가 최소화되도록 박막을 형성해야 한다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.145-145
• /
• 2011

Recently, multi-hole electrode RF capacitively coupled plasma discharge is being used in the deposition of microcrystalline silicon for thin film solar cell to increase the speed of deposition. To make efficient multi-hole electrode RF capacitively coupled plasma discharge, the hole diameter is to be designed concerning the plasma parameters. In past studies, the relationship between plasma parameters such as pressures and gas species, and hole diameter for efficient plasma density enhancement is experimentally shown. In the presentation, the relationship between plasma deriving frequency and hole diameter for efficient multi-hole electrode RF capacitively coupled plasma discharge is shown. In usual capacitively coupled plasma discharge, plasma parameter, such as plasma density, plasma impedence and plasma temperature, change as frequency increases. Because of the change, the optimum hole diameter of the multi-hole electrode RF capacitively coupled plasma for high density plasma is thought to be modified when the plasma deriving frequency changes. To see the frequency effect on the multi-hole RF capacitively coupled plasma is discharged and one of its electrode is changed from a plane electrode to a variety of multi-hole electrodes with different hole diameters. The discharge is derived by RF power source with various frequency and the plasma parameter is measured with RF compensated single Langmuir probe. The shrinkage of the hole diameter for efficient discharge is observed as the plasma deriving frequency increases.

• 한국재료학회지
• /
• 제9권10호
• /
• pp.1006-1011
• /
• 1999

$SiH_4$, $CH_4$, $B_2H_6$ 혼합기체를 이용하여 플라즈마 화학증착법으로 탄화실리콘 (a-SiC:H) 박막을 증착하였다. 증착중에 혼합기체중의$CH_4$농도 ($CH_4/CH_4+SiH_4$)를 변화시켜 얻은 박막의 물성을 SEM, XRD, Raman 분광법, FTIR, XPS, 광흡수도와 광전도도 분석을 통하여 살펴보았다. $SiH_4$기체만 이용하여 증착한 Si:H 박막은 비정질상태를 나타내었으나, $CH_4$가 첨가됨에 따라 실리콘 박막의 Si-$\textrm{H}_{n}$(n은 정수) 결합기가 Si-$\textrm{C}_{n}\textrm{H}_{m}$ (n,m은 정수) 형태의 결합기로 변화되었으며, 박막내 수소함량은 $CH_4$농도가 0~0.8의 범위에서 증가함에 따라 30~45% 범위에서 증가하였다. 반응기체중의 $CH_4$농도의 증가에 따라 박막 내의 탄소 농도가 증가함을 확인하였으며, 이에 따라 막의 전기비저항과 광학적밴드갭 역시 증가하였다.