• Journal of Animal Environmental Science
• /
• 제8권3호
• /
• pp.199-208
• /
• 2002

This paper introduces the method to make management network about milking cow farm tasks. The object of this research was to design of biological measuring system and managing network system in a livestock farm. This auto-management system provides informations about individual cows' temperature, conductivity of milk and weight for efficient management of feeding, and milking works by a micro-processor and RS -485 type serial COM. ports. And measured bio-data which are basic informations for remote raising management are saved to user PC by serial communication between the PLC and user PC. Milking cow farm is divided into three working place to each measurement work and feed. The first working place is milking station which has two thermometers, a conduct meter and a scale set. The second working place is feeding station, and the third place is cattle cage. These are combined by network system and the PLC which is used to drive network and sub-modules. Sub-modules have a micro-process to control the sensor and to interface with network. The PLC which drive network and control sequence has two serial communication port to be linked with user PC for sending the measured data and for receiving data. Above all, in this study tells the sequence operating method by the driving scenario of breeding milk cow for livestock auto-management using the PLC and network system.

• Korean Journal of Agricultural Science
• /
• 제11권2호
• /
• pp.322-327
• /
• 1984

As a basic studies for the laboratory scale production of alfalfa inoculum, Rhizobium meliloti M14 was characterized for its carbon and nitrogen sources, and some parameters for broth cultivation in a chemostat were studied by semi-continuous operation. The result s obtained were as follows. 1. Growth rate of the strain was increased by disaccharides than by monosaccharides tested, and pentoses resulted in poor growth than hexoses. Sugar alcohols including inositol supported the best growth among sugars. 2. Mannitol in the yeast-mannitol-broth was substituted by natural carbon sources such as malt extract or molasses. 3. Ten per cent of fresh yeast water appeared to supply enough amount of growth factor s for the strain, and the effect was equivalent to 0.24 percent of the commercial yeast extract powder. 4. Batch growth of the stain in a chemostat, New Brunswick Micro Ferm 28L, reached in the early stationary growth phase of $5{\sim}7{\times}10^9cells/ml$ after 36 hours of incubation. The culture at this stage was switched to semi-continuous cultivation, and the culture broth of four-fifth of the working volume was recovered every 24 hours when the maximal count was obtained.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2009년도 학술대회 초록집
• /
• pp.147-154
• /
• 2009

Physical properties of rocks, such as velocity, are strongly dependant on detailed pore structures, and recently, pore micro-structures by X-ray tomography techniques have been used to simulate and understand the physical properties. However, the smoothing effect during the tomographic reconstruction procedure often causes an artifact - overestimating the contact areas between grains. The pore nodes near a grain contact are affected by neighboring grain nodes, and are classified into grain nodes. By this artifact, the pore structure has higher contact areas between grains and thus higher velocity estimation than the true one. To reduce this artifact, we tried two image processing techniques - sharpening filter and neural network classification. Both methods gave noticeable improvement on contact areas between grains visually; however, the estimated velocities showed only incremental improvement. We then tried to change the resolutions of tomogram and quantify its impact on velocity estimation. The estimated velocity from the tomogram with higher spatial resolution was improved significantly, and with around 2 micron spatial resolution, the calculated velocity was very close to the lab measurement. In conclusion, the resolution of pore micro-structure is the most important parameter for accurate estimation of velocity using pore-scale simulation techniques. Also the estimation can be incrementally improved if combined with image processing techniques during the pore-grain classification.

• Current Industrial and Technological Trends in Aerospace
• /
• 제6권1호
• /
• pp.90-98
• /
• 2008

Nanotechnology(NT) refers to a field of advanced micro-technology covering the creation and manufacturing of materials on the atomic and molecular scale and requires interdisciplinary study with various fields including materials science, physics, chemistry, electronics and others. Whileas nanotechnology is a kind of micro and small scaled science, space technology(ST) is one of the larger and system technologies utilizing broad fields of mechanical, materials, electronics and communication technologies. It is necessary to select and concentrate the functional items of nanotechnology for efficient application to be utilized in space technology, due to the cross-sectional characteristics of nanotechnology within nanomaterials, nanoelectronics, and nanomanufacturing. This paper provides the current state of art of nanotechnology in space technology by evaluating NASA's activities and the 9th frame of the project ANTARES(Analysis of Nanotechnology Applications in Space Developments and Systems) with the support of the German Aerospace Center (DLR), Space Flight Management, Division Technology for Space Systems and Robotics. It has shown that it is necessary to apply nanotechnology to space technology in order to achieve international competitiveness, for the nanotechnology can bring the previously impossible things to reality. Since KARI plans to send an unmanned probe to the moon's orbit and land a probe on the moon's surface in 2025, it is urgently needed to incorporate nanotechnology to national space development plan.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.842-848
• /
• 2013

Developments of Solid-State Gyroscopy during last decades are impressive and were based on thin-walled shell resonators like HRG or CRG made from fused quartz or leuko-sapphire. However, a number of design choices for inertial-grade gyroscopes, which can be used for high-g applications and for mass- or middle-scale production, is still very limited. So, considerations of fundamental physical effects in solids that can be used for development of a miniature, completely solid-state, and lower-cost sensor look urgent. There is a variety of different types of bulk acoustic (elastic) waves (BAW) in anisotropic solids. Shear waves with different variants of their polarization have to be studied especially carefully, because shear sounds in glasses and crystals are sensitive to a turn of the solid as a whole, and, so, they can be used for development of gyroscopic sensors. For an isotropic medium (for a glass or a fine polycrystalline body), classic Lame's theorem (so-called, a general solution of Elasticity Theory or Green-Lame's representation) has been modified for enough general case: an elastic medium rotated about an arbitrary set of axes. Travelling, standing, and mixed shear waves propagating in an infinite isotopic medium (or between a pair of parallel reflecting surfaces) have been considered too. An analogy with classic Foucault's pendulum has been underlined for the effect of a turn of a polarizational plane (i.e., an integration effect for an input angular rate) due to a medium's turn about the axis of the wave propagation. These cases demonstrate a whole-angle regime of gyroscopic operation. Single-crystals are anisotropic media, and, therefore, to reflect influence of the crystal's rotation, classic Christoffel-Green's tensors have been modified. Cases of acoustic axes corresponding to equal velocities for a pair of the pure-transverse (shear) waves have of an evident applied interest. For such a special direction in a crystal, different polarizations of waves are possible, and the gyroscopic effect of "polarizational precession" can be observed like for a glass. Naturally, formation of a wave pattern in a massive elastic body is much more complex due to reflections from its boundaries. Some of these complexities can be eliminated. However, a non-homogeneity has a fundamental nature for any amorphous medium due to its thermodynamically-unstable micro-structure, having fluctuations of the rapidly-frozen liquid. For single-crystalline structures, blockness (walls of dislocations) plays a similar role. Physical nature and kinematic particularities of several typical "drifts" in polarizational BAW gyros (P-BAW) have been considered briefly too. They include irregular precessions ("polarizational beats") due to: non-homogeneity of mass density and elastic moduli, dissymmetry of intrinsic losses, and an angular mismatch between propagation and acoustic axes.

• The Korean Journal of Quaternary Research
• /
• 제25권2호
• /
• pp.25-37
• /
• 2011

The purpose of this study is to assume the particular area of hills where it is highly possible for historical site to be buried in the viewpoint of geomorphology and based on this to suggest excavation-recommended area. Namely, this writer is to understand the dwelling site type of ancient people who had resided there at that time for the object of 'Ohnju region urban development business site' (referred as investigation area hereinafter) and considering the characteristics of micro-landform of hills which are distributed in investigation area and is to recommend the area where it is highly possible for historical site to be buried. The result of analysis is like the following. (1) Dwelling site types of ancient people who might have resided in the whole area of investigation region are discovered to be largely 'low hills+wetland' of Type-I and 'alluvial fan(or river terrace+wetland' of Type-II. (2) In investigation area if the area which has high possibility of distribution of historical site namely, excavation-recommended area is looked as based on micro-landform unit of hills, they are Crest slope and Crest flat. Individual area ratios which Crest slope and Crest flat occupies in investigation area are 12.9% and 10.2% respectively and the rankings are 3 and 6 each. And excavation-recommended areas in valley plain(or bottomland) of investigation area are in the vicinity of 'distal end' or 'buried distal end'of small scale alluvial fan.

• Journal of KIISE:Computing Practices and Letters
• /
• 제10권2호
• /
• pp.134-145
• /
• 2004

With rapid growth in the amount of data transferred on the Internet, traditional storage systems have reached the limits of their capacity and performance. SAN (Storage Area Network), which connects hosts to disk with the Fibre Channel switches, provides one of the powerful solutions to scale the data storage and servers. In this environment, the maintenance of data consistency among hosts is an important issue because multiple hosts share the files on disks attached to the SAN. To preserve data consistency, each host can execute the disk I/O whenever disk read and write operations are requested. However, frequent disk I/O requests cause the deterioration of the overall performance of a SAN cluster. In this paper, we introduce a SANtopia global buffer manager to improve the performance of a SAN cluster reducing the number of disk I/Os. We describe the design and algorithms of the SANtopia global buffer manager, which provides a buffer cache sharing mechanism among the hosts in the SAN cluster. Micro-benchmark results to measure the performance of block I/O operations show that the global buffer manager achieves speed-up by the factor of 1.8-12.8 compared with the existing method using disk I/O operations. Also, File system micro-benchmark results show that SANtopia file system with the global buffer manager improves performance by the factor of 1.06 in case of directories and 1.14 in case of files compared with the file system without a global buffer manager.

• Clean Technology
• /
• 제19권4호
• /
• pp.355-369
• /
• 2013

Economic feasibility is one of the most important factors in energy production from regenerative biomass. From the aspect, biogas from anaerobic digestion of wastewater sludge is regarded as the most economical because of its cheap substrate and additional income from the disposal of waste sludge. Sludge hydrolysis has been regarded as the rate limiting step of anaerobic digestion and many sludge pre-treatment technologies have been developed to accelerate anaerobic sludge digestion for enhanced biogas production. Various sludge pre-treatment technologies including biological, thermo hydrolysis, ultrasonic, and mechanical methods have been applied to full-scale systems. Sludge pre-treatment increased the efficiency of anaerobic digestion by enhancing hydrolysis, reducing residual soilds, and increasing biogas production. This paper introduces the characteristics of various sludge pre-treatment technologies and the energy balance and economic feasibility of each technology were compared to prepare a guideline for the selection of feasible pre-treatment technology. It was estimated that thermophilic digestion and thermal hydrolysis were most economical technology followed by Cell rupture$^{TM}$, OpenCEL$^{TM}$, MicroSludge$^{TM}$, and ultrasound. The cost for waste sludge disposal shares the biggest portion in the economic analysis, therefore, water content of the waste sludge was the most important factor to be controlled.

• Korean Journal of Materials Research
• /
• 제12권9호
• /
• pp.750-760
• /
• 2002

In this study, three solders, Sn-37Pb, Sn-3.5Ag, and Sn-3.8Ag-0.7Cu were screen printed on both electroless Ni/Au and OSP metal finished micro-via PCBs (Printed Circuit Boards). The interfacial reaction between PCB metal pad finish materials and solder materials, and its effects on the solder bump joint mechanical reliability were investigated. The lead free solders formed a large amount of intermetallic compounds (IMC) than Sn-37Pb on both electroless Ni/Au and OSP (Organic Solderabilty Preservatives) finished PCBs during solder reflows because of the higher Sn content and higher reflow temperature. For OSP finish, scallop-like $Cu_{6}$ /$Sn_{5}$ and planar $Cu_3$Sn intermetallic compounds (IMC) were formed, and fracture occurred 100% within the solder regardless of reflow numbers and solder materials. Bump shear strength of lead free solders showed higher value than that of Sn-37Pb solder, because lead free solders are usually harder than eutectic Sn-37Pb solder. For Ni/Au finish, polygonal shaped $Ni_3$$Sn_4$ IMC and P-rich Ni layer were formed, and a brittle fracture at the Ni-Sn IMC layer or the interface between Ni-Sn intermetallic and P-rich Ni layer was observed after several reflows. Therefore, bump shear strength values of the Ni/Au finish are relatively lower than those of OSP finish. Especially, spalled IMCs at Sn-3.5Ag interface was observed after several reflow times. And, for the Sn-3.8Ag-0.7Cu solder case, the ternary Sn-Ni-Cu IMCs were observed. As a result, it was found that OSP finished PCB was a better choice for solders on PCB in terms of flip chip mechanical reliability.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2000년도 제18회 학술발표회 논문개요집
• /
• pp.77-77
• /
• 2000

Titanium oxide (TiO2) thin films have valuable properties such as a high refractive index, excellent transmittance in the visible and near-IR frequency, and high chemical stability. Therefore it is extensively used in anti-reflection coating, sensor, and photocatalysis as electrical and optical applications. Specially, TiO2 have a high dielectric constant of 180 along the c axis and 90 along the a axis, so it is highlighted in fabricating dielectric capacitors in micro electronic devices. A variety of methods have been used to produce patterned self-assembled monolayers (SAMs), including microcontact printing ($\mu$CP), UV-photolithotgraphy, e-beam lithography, scanned-probe based micro-machining, and atom-lithography. Above all, thin film fabrication on $\mu$CP modified surface is a potentially low-cost, high-throughput method, because it does not require expensive photolithographic equipment, and it produce micrometer scale patterns in thin film materials. The patterned SAMs were used as thin resists, to transfer patterns onto thin films either by chemical etching or by selective deposition. In this study, we deposited TiO2 thin films on Si (1000 substrateds using titanium (IV) isopropoxide ([Ti(O(C3H7)4)] ; TIP as a single molecular precursor at deposition temperature in the range of 300-$700^{\circ}C$ without any carrier and bubbler gas. Crack-free, highly oriented TiO2 polycrystalline thin films with anatase phase and stoichimetric ratio of Ti and O were successfully deposited on Si(100) at temperature as low as 50$0^{\circ}C$. XRD and TED data showed that below 50$0^{\circ}C$, the TiO2 thin films were dominantly grown on Si(100) surfaces in the [211] direction, whereas with increasing the deposition temperature to $700^{\circ}C$, the main films growth direction was changed to be [200]. Two distinct growth behaviors were observed from the Arhenius plots. In addition to deposition of THe TiO2 thin films on Si(100) substrates, patterning of TiO2 thin films was also performed at grown temperature in the range of 300-50$0^{\circ}C$ by MOCVD onto the Si(100) substrates of which surface was modified by organic thin film template. The organic thin film of SAm is obtained by the $\mu$CP method. Alpha-step profile and optical microscope images showed that the boundaries between SAMs areas and selectively deposited TiO2 thin film areas are very definite and sharp. Capacitance - Voltage measurements made on TiO2 films gave a dielectric constant of 29, suggesting a possibility of electronic material applications.