• 제목/요약/키워드: Micro-hole

검색결과 328건 처리시간 0.02초

유한요소법에 의한 결함 주위의 응력분포와 피로크랙의 간섭효과 (Analysis of the stress disribution around flaws and the interaction effects between fatigue cracks by finite element method)

  • 송삼홍;김진봉
    • 한국정밀공학회지
    • /
    • 제12권2호
    • /
    • pp.154-161
    • /
    • 1995
  • In order to analysis of the stress distribution around flaws and the interaction effects between fatigue cracks, stress around micro hole was analyzed by Finite Element Method(F.E.M.) and micro hole specimens were tested using rotary bending fatigue machine and twisting fatigue machine to identify stress effects for fatigue cracks initiating from micro holes and interaction effects between micro holes. The results are as follows : Interaction effects of .sigma. $_{y}$for the micro hole side is larger than the large micro hole side when the interval between micro holes is near. Stress concentration factor increase as the diameter of micro hole becomes smaller. But, stress field of micro hole is smaller than that of large micro hole at h .leq. r (h:depth of micro hole, r:radius of micro hole) and that of large hole is larger than that of small micro hole at h >r expect the small range from micro hole.e.

  • PDF

미소원공주위의 피로크랙발생전파 거동에 관한 연구 (Behavior of Initiation and Propagation of Fatigue Cracks around Microholes)

  • 송삼홍;오환석
    • 한국해양공학회지
    • /
    • 제1권2호
    • /
    • pp.74-82
    • /
    • 1987
  • This study has been made to investigate into the behavior of fatigue limit, of fatigue crack initiation, and of fatigue crack propagation under the condition of rotating bending stress; specifically on the independency of stress field as well as the crack behavior of surface micro hole defect, which is made artificially through the specimen. The results obtained can be summarized as followa; 1) For the single micro hole defect, initiation of fatigue crack is occurred at both tips of microhole defect simultaneosly along the slip which are produced in the range of maximum principal stress arround micro hole defect independent of the size of micro hole defect. 2) For the neighbored deuble micro hole defects with equal size, in the range ($\frac{L}{r}$)ratio $\gtrsim$ 3 defined as the size of micro hole defect(2r) to the distance between the centers of micro hole defects (2L), the crack behavior of the micro hole defects is same as single one. However, for the range of $\frac{L}{r}$<3, the interference effect becomes significant as the ratio approaches to 1.

  • PDF

방전 가공을 이용한 미세 구멍 가공 시 발생하는 테이퍼 형상의 제어 (Control of Taper Shape in Micro-Hole Machining by Micro-EDM)

  • 김동준;이상민;이영수;주종남
    • 한국정밀공학회지
    • /
    • 제22권4호
    • /
    • pp.52-59
    • /
    • 2005
  • When a micro hole is machined by EDM with a cylindrical electrode, the hole diameter is different at the inlet and the outlet of the micro hole. The taper shape of the micro hole is caused by not only wear of the electrode but the eroded particles. The eroded particles cause secondary discharge during machining the micro hole. As a result, the diameter of the inlet becomes larger than that of the outlet. In this paper, a new method is proposed to reduce the difference in diameter between the inlet and the outlet of the hole. Observed was that the feed depth and machining time affect the formation of taper shape On this experimental basis, ultrasonic vibration was applied to reduce machining time, and capacitance was changed during machining to use the difference in discharging energy of different capacitances. Using the proposed method, a straight micro-hole was fabricated.

마이크로 펀칭용 미세축, 미세구멍의 가공 (Micro-shaft and Micro-hole Machining for Micro Punching)

  • 류시형;조필주;이강희;주종남
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2002년도 금형가공 심포지엄
    • /
    • pp.239-244
    • /
    • 2002
  • In this study, we developed the manufacturing technology of micro-hole and micro-shaft for micro punching system using micro electrical discharge machining and micro electro chemical machining. Micro punching dies of tungsten carbide with $55\;{\mu}m\;and\;110\;{\mu}m$ diameter and $250\;{\mu}m$ depth were made by micro electrical discharge machining. The form accuracy and surface roughness of die hole were pretty good and it was shown that the punched hole quality was fine. WC micro-shaft with $30\;{\mu}m$ diameter was made by the multistep micro electro chemical machining. The developed technologies can be effectively used in precision manufacturing of micro punching die and mass production of micro-shaft.

  • PDF

소프트 다이 플레이트를 이용한 미세 구멍 펀칭 연구 (A Study on Micro Hole Punching with Soft Die Plate)

  • 유준환;주병윤;전병희;오수익
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2002년도 금형가공 심포지엄
    • /
    • pp.260-265
    • /
    • 2002
  • In micro hole punching process, it is very difficult to align punch with die hole. Misalignment can cause a falling-on in hole quality and breakage of punch and die. Micro punching using soft die plate without a die hole has a big advantage because it is not necessary to align punch with die hole and to consider die clearance. Soft die plates are made by polymers or hard rubbers which are softer than metals. In this study, several micro punching experiments are conducted. Micro punching test with some materials shows that micro hole punching is feasible with some soft die plates. Through the section shape obtained by mounting and polishing, the punched hole quality is measured and the shapes of burr and dome we studied.

  • PDF

미소결함간의 응력의 간섭과 응력장 해석 (A Study of Stress Analysis and Interaction of Stress between Micro Flaws and Inclusions)

  • 송삼홍;김진봉
    • 대한기계학회논문집
    • /
    • 제19권5호
    • /
    • pp.1259-1268
    • /
    • 1995
  • The stress distribution around micro holes and the behavior of stress interaction between micro holes are considerd in the study. Several conclusions are extracted as follows : (1) The stress interaction varies with the distance e between micro holes. When the two micro holes are spaced in such a manner that theri two closest points are separated by a distance of micro hole radius (e=1), stress distribution is affected by a opposite micro hole in all the closest region. In addition, if two closest points are seperated by twice the distance of a micro hole radius (e=2), stress distribution is affected by a opposite micro hole in the region of -0.8.leq.x/r.leq.0.8 and the interaction effect can be neglected for e=4. (2)If the depth becomes larger than the radius, or the radius varies, the shape and magnitude of stress distribution around micro holes varies. (3) Hoop stress around a micro hole for the two dimensional configuration is larger than that of the three dimensional micro hole located on the surface of material for .theta. < 60.deg., but it is reversed for .theta > 60.deg.

극대세장비 마이크로 홀을 이용한 양성자 빔 집적 응용 (A Proton Beam Shaping using an Extreme Aspect Ratio Micro-hole)

  • 김진남;권원태;이성규
    • 한국정밀공학회지
    • /
    • 제29권7호
    • /
    • pp.737-744
    • /
    • 2012
  • EDM is the manufacturing process that uses the thermal energy to machine electrically conductive part. Despite a lot of research has been conducted for decades, the best aspect ratio of the micro hole using micro-EDM has not been over 30, yet. In the present study, new fabrication scheme was introduced to increase the aspect ratio of micro hole dramatically. Micro holes with less than 10 aspect ratio were aligned and welded together to manufacture a micro hole with extreme aspect ratio. Alignment of the micro hole with over 380 aspect ratio was conducted by the home-made apparatus installed with microscope and laser beam. The micro hole with extreme aspect ratio was used to shape pencil beam from proton beam generated from MC-50 cyclotron. The pencil beam was utilized to machine test specimen whose result was compared with GEANT4 computer simulation. It was shown that the experimental and simulation result were closer as the aspect ratio of the micro hole was bigger.

미세 구멍가공을 위한 전극성형 가공특성에 관한 연구 (A Study on the Characteristics of Electrode Fabrication for Micro Hole-making)

  • 이주경;이종항;박철우;조웅식
    • 대한기계학회논문집A
    • /
    • 제31권11호
    • /
    • pp.1053-1058
    • /
    • 2007
  • Micro-EDM technology (or the manufacture of miniature parts is used to make a micro hole. Two electrode shaping methods, mechanical electrode grinding and WEDG technique, have been studied. In this study, an electrode shaping method by using previously machined hole is introduced in order to obtain an optimal hole-making condition. Key factors such as applied voltage, capacitance, feedrate, and hole-dimension have an influence on the fabricating error of electrode shaping, which are taper ratio of a hole, electrode form accuracy, and electrode surface. Therefore, we try to investigate the optimal fabricating of electrode shaping from various experiments. Results from experiments, it was able to minimize the electrode fabricating error as voltage increases, and also applied feedrate and capacitance decreases.

表面欠陷 에 發생하는 疲勞크랙擧動 (Behavior of Fatigue Crack Propagation from Surface Flaw)

  • 송삼홍;오환섭
    • 대한기계학회논문집
    • /
    • 제9권2호
    • /
    • pp.150-157
    • /
    • 1985
  • 본 연구에서는 자연적인 미소흠함주위에 발생, 전파하는 피로크랙의 거동을 검토하기 위하여, 기존재료가 갖고 있는 흠함이나 비금속개재물을 대신할 수 있다고 생각되는 크기가 다른 비관통 인공미성구멍을 갖는 여러 종류의 시험편을 준비하고, 이 시험편들이 갖는 인공미성구멍주위에 발생전파하는 피로크랙의 거동을, 금속현미경 관찰을 토대로 상세히 고찰하였다. 그리고 이러한 관찰을 기초로 하여 비관통인공미 성구멍의 대성에 따른 피로한계도거동에 대해서도 고찰하였다.

MICRO HOLE FABRICATION BY MECHANICAL PUNCHING PROCESS

  • Joo B. Y.;Rhim S. H.;Oh S. I.
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2003년도 The 8th Asian Symposium on Precision Forging ASPF
    • /
    • pp.179-188
    • /
    • 2003
  • The objective of our study is to investigate the micro fabric ability by conventional metal forming processes. In the present investigation, micro hole punching was studied. We tried to control punching process at the micro level and scaled down the standard blanking condition for $25{\mu}m$ hole fabrication. To accommodate this, tungsten carbide tooling sets and micro punching press were carefully designed and assembled meeting accuracy requirements for $25{\mu}m$ hole punching. With our developments, 100, 50, and $25{\mu}m$ holes were successfully made on metal foils such as brass and stainless steel of 100, 50, and $25{\mu}m$ in thickness, respectively, and hole sizes and shapes were measured and analyzed to investigate fabrication accuracy. Shear behavior during micro punching was also discussed. Our study showed that the conventional punching process could produce high quality holes down to $25{\mu}m$.

  • PDF