• Textile Coloration and Finishing
• /
• v.13 no.6
• /
• pp.428-434
• /
• 2001

This study surveys the fiber behavior in yam formation and the Physical properties of Solo-spun yarn. The specimens were made by six types of Solo-spun rollers with fixed twist multiplier In the previous part, the physical properties such as yarn count, evenness, strength, and breaking elongation of these yams were compared with the properties of ring shun yarns and analysed with the mechanism of Solo-spun yarn formation. In the second part of this report, the abrasion resistance and hairiness were discussed wish respect to the micro yarn structures. The narrower the groove width of Solo-spun roller is, the more active the bulk fibers migration is. The Solo-spun film structure has two groups. One is shorter than the others one in longitudinal direction of yarn and has the same structure as ring-spun yarn, which is derided from the smooth zone on the surface of Solo-spun roller. The other one is longer than the former and there are the wrapping fibers. This part is derived from the conflicted grooves on the surface of Solo-spun troller.

• Textile Coloration and Finishing
• /
• v.13 no.6
• /
• pp.70-70
• /
• 2001

This study surveys the fiber behavior in yarn formation and the Physical properties of Solo-spun yarn. The specimens were made by six types of Solo-spun rollers with fixed twist multiplier In the previous part, the physical properties such as yarn count, evenness, strength, and breaking elongation of these yarns were compared with the properties of ring spun yarns and analysed with the mechanism of Solo-spun yarn formation. In the second part of this report, the abrasion resistance and hairiness were discussed with respect to the micro yarn structures. The narrower the groove width of Solo-spun roller is, the more active the bulk fiber migration is. The Solo-spun yarn structure has two groups. One is shorter than the other one in longitudinal direction of yarn and has the same structure as ring-spun yarn, which is derived from the smooth zone on the surface of Solo-spun roller. The other one is longer than the former and there are the wrapping fibers. This part is derived from the conflicted grooves on the surface of Solo-spun roller.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1125-1128
• /
• 2007

The laminating technique for developing flexible liquid crystal display was demonstrated by using a thin UV curable polymer film and a plastic substrate with patterned polymer wall structure. We adopted the rigid wall structure to provide a solid mechanical support for the stable molecular alignment of liquid crystals (LCs) in the device. The cover film was prepared to have an ability of aligning LC molecules by patterning a micro-groove structure using the soft-lithographic process. These two substrates can be assembled tightly by the laminating and one-step UV irradiation process because of the adhesive nature of the used UV curable polymers. Proposed method can be used to fabricate the flexible LC display with simplicity and also be applicable for a cost-effective roll-to-roll process.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1918-1920
• /
• 2001

초소형 히트파이프는 고집적 반도체 소자에서 발생되는 열을 효과적으로 소산하기 위한 열교환 장치이다. 초소형 히트파이프는 작동유체가 상 변화 잠열을 이용한 칩 레벨의 냉각 장치이다. 작동유체는 진공으로 밀봉된 공간내에서 외부 동력 없이 모세관력에 의하여 이동한다. 본 논문에서는 실리콘보다 열전도도가 우수하여 발생되는 열을 더욱 빠르게 소산시킬 수 있는 구리 모재의 초소형 히트파이프를 제작한다. 특히, 모세관력은 히트파이프의 성능을 좌우하는 요소이다. 모세관력 향상을 위해서 구리 전기도금으로 이용하여 홈(groove)부분을 제작한다. 윅(wick) 제작, 구리판 접합, 작동유체 충전등으로 초소형 히트파이프를 제작한 후, 성능 실험한 결과를 보여준다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.81-83
• /
• 2003

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with rubbing alignment method on polyimide surfaces using thin plastic substrates. It was found that monodomain alignment of LNC is obtained with rubbing alignment method on polyimide surfaces using thin plastic substrates. The generated NLC pretilt angles are about $3^{\circ}$ by the rubbing alignment method on thin plastic substrates, However, the pretilt angle measured at about $1.7^{\circ}$ lower on the glass substrate than by thin plastic substrate. It is considered that this alignment may be attributed to roughness of micro groove substrate. The tilt angle increases with increasing baking temperature for making polyimide layer using glass substrate. It was concluded that pretilt angle in the polyimide surface is attributable to the increasing of imide rato.

• Fibers and Polymers
• /
• v.3 no.3
• /
• pp.113-119
• /
• 2002

Nanoimprint lithography (NIL) is a nanofabrication method known to be a low cost method of fabricating nanoscale patterns as small as 6 m. This study is focused on understanding physical phenomena in the embossing of nano/micro scale structures with 100 nm minimum feature size. We present the effects of capillary force and width of stamp groove on flow behavior at the embossing stage through numerical experimentation. We also compare our numerical results with previous experimental results and discuss our results.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2003.04a
• /
• pp.70-79
• /
• 2003

Paper coating can give smoothness surface and good printability to uncoated paper. Macro roughness of base paper would be decreasing its groove and grit in view of side. Nevertheless its improving effect for paper, some kind of problem is showing in the fine coated paper. Especially, back trap mottle is one of serious problems in printing with fine coated paper. Printers can not adjust conditions to overcome the problem. Also large amounts of paper can be rejected. There are many factors that influence back trap mottle. However it is not clear what the important parameters are in back trap mottle. Back trap mottle has some relationship with ink setting but good guidelines are not clear. Back trap mottle has been linked to non-uniform ink setting. We do not know how much variation in setting we can tolerate. Other mottle issues such as micro-picking and ink refusal are still common. This paper was prepared to identify correlation with ink setting and delta ink density obtained from experiment and then tried to find out some relationships with ink setting and back trap mottle. Basically fine calcium carbonate and ciay was used for main components and coarse calcium carbonate was mixed in two fine pigments to change its porosity and ink acceptance. Micro ink tack force at KRK printing tester was adapted to measure ink setting rate. KRK units were used for back trap mottle simulation and two printed samples were prepared to check delta ink density. Clay base coating has more fast ink setting time than calcium carbonate's though smoothness of clay was better than calcium carbonate. It could be explained by that clay has finer pore in its coating than calcium carbonate. DID(delta ink density) has shown a good correlation with ink setting time from micro ink tack. The total pore volume of coating layer did not match with ink setting and DID. From the results we might conclude coating that has fine pore size around 0.05 ${\mu}m$ can be exposed to high possibility of back trap mottle.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.60 no.2
• /
• pp.25-36
• /
• 2018

Drip irrigation system is a low energy cost method which can efficiently save and supply water by dropping water slowly on the crop's root zone during crop growth. In the drip irrigation system, disk filters take an important role to physically remove impurity (inorganic and suspended organic) particles present in agricultural water which can cause emitter clogging. For the purpose, both top-and-bottom surfaces of the disk are grooved in micron size flowing from outside to inside. However, many congested flow paths in disk filter media incur higher head loss of inflow water resulting in relatively decreasing velocities depending on operation time than sand and mesh filters. Therefore, it is important to optimize the structure of disk filter in micro irrigation system. The head loss of disk filter media takes also charge of more than 60 % of total head loss in whole disk filter. This study is to find the appropriate cross-sectional shape of the disk groove to minimize the head loss by executing the experiment. The experiment used three disk filters that have similar filter body but have a half-elliptic and two kinds of triangular cross sections. The experimental results showed that the disk filter with half-elliptic cross sections of disk grooves have less head loss than the disk filter with regular triangular one.

• Transactions of Materials Processing
• /
• v.29 no.2
• /
• pp.103-112
• /
• 2020

This study explores the effects of different pre-machining conditions on the deposition characteristics and mechanical properties of austenitic stainless steel samples repaired using direct energy deposition (DED). In the DED repair process, defects such as pores and cracks can occur at the interface between the substrate and deposited material. In this study, we varied the shape of the pre-machined zone for repair in order to prevent cracks from occurring at the slope surface. After repairs by the DED process, macro-scale cracks were observed in samples that had been pre-machined with elliptic and trapezoidal grooves. In addition, it was not possible to completely prevent micro-crack generation on the sloped interfaces, even in the capsule-type grooved sample. From observation of the fracture surfaces, it was found that the cracks around the inclined interface were due to a lack of fusion between the substrate and the powder material, which led to low tensile properties. The specimen with the capsule-type groove provided the highest tensile strength and elongation (respective of 46% and 571% compared to the trapezoidal grooved specimen). However, the tensile properties were degraded compared to the non-repaired specimen (as-hot rolled material). The fracture characteristics of the repaired specimens were determined by the cracks at the sloped interfaces. These cracks grew and coalesced with each other to form macro-cracks, they then coalesced with other cracks and propagated to the substrate, causing final fracture.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.30-30
• /
• 2010

고강도강의 용접성은 저온균열 저항성으로 대변되는데, TMCP강과 HSLA강 등이 개발되면서 고강도강의 저온균열저항성이 크게 향상되어 무예열 용접성이 확보되었다. 그러나 용접재료 측면에서는 그에 상응하는 재료의 개발이 지연되어 강재 개발로 인한 우수한 성능을 충분히 발휘하지 못하고 있으며 용접부의 건전성 문제가 심각하게 인식되고 있다. 이로 인해 고강도강에 적용시킬 수 있는 무예열 용접재료의 필요성이 대두되어 개발이 진행되고 있으며 상용화를 앞두고 있다. 이러한 용접재료의 개발단계에서 합금설계는 가장 중요한 항목으로 합금 조성에 따라 용착금속의 강도 및 인성에 상당한 변화를 가져오기 때문이다. 합금원소 중 Al은 강재의 탈산을 돕기 때문에 가능한 많은 양의 첨가를 요구하지만 적정량 이상을 초과하게 되면 오히려 용착금속의 저온인성 특성에 부정적인 영향을 미치게 된다. 본 연구에서는 고강도 GMA 용착금속의 Al함량을 단계적으로 변화시켜 용착금속 내 최적의 Al의 함량을 찾고자 하였다. 또한 높은 비용 및 많은 시간을 필요로 하는 와이어로드를 제작하지 않고도 Al함량을 조절 할 수 있는 방법을 고안하고자 하였다. 실험의 모재는 HSLA-100강을 사용하였으며 용접재료는 ER120S-G급의 GMA용접 재료를 사용하였다. 모재 성분과의 희석을 방지하기 위해 V-Groove 가공 후 6패스 Buttering 용접을 실시하였고, 다시 Buttering용접부에 V-Groove 가공을 하여 최종 용접을 실시하였다. 이 때 Al함량을 조절하기 위해 최종 용접 개선부 밑면에 홈을 판 후 Al fiber(직경 0.3mm)를 깔고 용접(입열량 20kJ/cm)하여 Al함유량을 총 3가지(0.003~0.04% Al)로 제어하였다. 용접 후 각각의 시편에 대해 미세조직, 충격시험, O/N분석, 성분분석 등의 시험을 수행하여 저온인성과의 상관관계를 알아보았다.