• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.1807-1818
• /
• 1991

The frictional characteristic of Zn-Ni electrogalvanized steel sheet was investigated by experimental procedures. To clarify the effect of surface property on the frictional characteristic of Zn-Ni coated steel sheet, Micro-hardness test, SEM analysis and X-ray diffraction analysis were carried out. Coefficients of friction for various stamping lubricant and Ni content in coated layer were measured by a draw bead friction test. The results show that frictional characteristic is very sensitive to Ni content of coated layer and depends on stamping lubricant. For Ni content less than about 11%, selection of proper lubricant is necessary to obtain low coefficient of friction in Zn-Ni coated steel sheet such as in case of cold rolled steel sheet.

• Journal of Power System Engineering
• /
• v.11 no.1
• /
• pp.115-120
• /
• 2007

The effect of grain size on the damping capacity of Fe-26Mn-2Al alloy studied in this paper has been investigated after changing the microstructure by cold rolling and changing grain size. Micro structures in Fe-26Mn-2Al at room temperature consist of a large quantity of austenite and a small quantity of ${\varepsilon}\;and\;{\alpha}'$ martensite. And ${\varepsilon}\;and\;{\alpha}'$ martensite was increased by increasing the degree of cold rolling. The content of deformation induced martensite was increased with increasing the degree of cold rolling. Damping capacity was linearly increased with increasing ${\varepsilon}$ martensite content, which suggests that stacking faults and ${\varepsilon}$ martensite variant boundaries are the principle damping sources. With increasing the grain size in Fe-26Mn-2Al alloy, the damping capacity was increased due to increasing the volume fraction of ${\varepsilon}$ martensite by decrement in stability of austenite phase. With decreasing the grain size, the content of deformation induced martensite was decreased and the damping capacity was decreased.

• Journal of Marine Bioscience and Biotechnology
• /
• v.14 no.2
• /
• pp.69-75
• /
• 2022

The micro-Kjeldahl method, a common technique for analyzing crude proteins, is time-consuming and dangerous due to the employment of reagents such as sulfuric acid and sodium hydroxide. However, a Fourier transform near-infrared (FT-NIR) spectrophotometer analysis can be completed in under a minute after simple pre-processing if data has been gathered using sufficient reference material in advance. Furthermore, the use of safe reagents in this technique ensures the safety of the experimenter and the environment. In addition, a portable FT-NIR spectrophotometer enables real-time measurement at processing or distribution sites and has recently gained popularity. The standard errors of calibration and regression (r²) for the calibration result for estimating the crude protein content of dried laver were 0.9775 and 1.2526, respectively. The standard error of prediction was 1.1814, and the r² was 0.9303 in the validation results, which was a good level. In the present study, a method for predicting the crude protein content of dried laver using an FT-NIR spectrophotometer in the range of 29%-40% crude protein content has been reported.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.4
• /
• pp.123-130
• /
• 2020

Nano seed incorporated in micro-sized 4BS (Tetrabasic lead Sulfate) seed was applied to the positive electrode active material and compared with Nano 4BS seed (NS). The dispersion of NS decreased due to the aggregation phenomenon, while the nano seed incorporated in micro-sized 4BS seed (INS) could confirm excellent dispersion. As the content of INS increased, the particle size of the active material became small and constant, which was confirmed through SEM and particle size analysis. The specific surface area for the reaction was increased and the high-rate discharge and lifetime characteristics were improved. In order to confirm the variation in particle size distribution in the plate manufacturing process, internal resistance and voltage were measured for 200 AGM lead-acid batteries, and it was confirmed that batteries quality variation decreased.

• The Journal of Korean Academy of Prosthodontics
• /
• v.22 no.1
• /
• pp.95-108
• /
• 1984

Even though the tarnishing and corrosion problems characteristic with dental silver-palladium alloy are not yet fully solved, it is recently widely used because of its low cost. However the effects of major alloying elements on the various properties of this system are not fully understood. The object of this research is to clarify the effects of In and Zn additives on the corrosion and tarnishing resistances and precipitation hardening behavior of this sytem, using electrodynamic polarization, immersion, and Vicker's microhardness test and X-ray diffraction and electron probe micro analysis methods. The obtained results were as follows: I. As indium content is increased, both the corrosion resistance in Cl-solution and microhardness are also increased while the tarnishing resistance is decreased. 2. As Zinc content is increased, the corrosion resistance is decreased, but tarnishing resistance is increased 3. At 70Ag-25Pd-2.5Zn-2.5In composition, the precipitation harding behavior was mot significant. The optimum aging temperature was $450^{\circ}C$ and the time was 2 hrs. The resulting specimen of this work carried 180VHN. 4. Under the heat treatment, the changes in the mechanical property are due to the changes in the shape and composition of dendrite matrix, namely, it is because of the precipitation hardening behavior which has been proved by electron probe micro analysis and optical microscopic finding.

• Resources Recycling
• /
• v.22 no.1
• /
• pp.20-28
• /
• 2013

Recently, as the registration of vehicles increases, the utilization of the waste tires is emerging as environmental issues. Crumb rubber reproduced by scrap tires has been reused up to 25% in the construction field. The purpose of this paper is to investigate the mechanical properties of sulfur-rubber concrete (SRC) and to suggest the optimum mix design in terms of the compressive strength. Specimens were prepared with various mixing parameters: amount of sulfur, rubber, and micro-fillers. Two casting processes were also mentioned; dry process and wet process. The results mainly showed that the compressive strength of SRC decreased with an increment of rubber content. However, adding micro-filler and adjusting sulfur contents could improve the compressive strength of SRC. Optimum values of sulfur and rubber content were selected by workability and compressive strength of SRC. SRC can be applied to road constructions where high strength of concrete is not concerned, to wall panels that require low unit weight, to construction of median in highways to resist high impact load, and in sound barriers to absorb sound waves.

• Journal of Conservation Science
• /
• v.17 s.17
• /
• pp.57-64
• /
• 2005

In the course of examining the micro structure of Iron chisel and Iron arrowhead, a relics of the 16th or 17th of Chosun Dynasty unearthed at near Gangsun-tower, Chengpyeong temple. Collected un-eroded samples from the relics were looked into the metallic structure through optical metallography. Non-metallic inclusions were-analysed by SEM and EDS. The micro structure examination and SEM-SDS analysis revealed that Iron chisel and Iron arrowhead had been produced from the sponge iron close to pure iron made by low temperature reducing in a solid and then the surface carbon content was increased by carburizing treatment. It was also found that Iron chisel had been hardened through the repetitive processes of quench hardening and heat treatment, after increasing carbon content to a certain level. Up to now, there have been a number of studies in the domestic academia which were studied mainly on the structure of metallic relics in the period of the Three Kingdoms or before. Although this research was limited in type and number of the relics, it turned out to be interesting in that it revealed the 16th or 17th century way of processing iron, even in fragments. It is thought to be fruitful that iron had been made even in the Chosun Dynasty from the sponge iron.

• Journal of Animal Science and Technology
• /
• v.58 no.12
• /
• pp.42.1-42.8
• /
• 2016

Background: Deficiency of macro and micro-minerals in the ration of dairy cows adversely affects growth, milk production and reproduction efficiency. It is essential to examine mineral concentrations in feeds offered to dairy cows in practical farms. Methods: Two villages from each taluka were selected at random for taking representative samples of feeds, forages and hair. Within the village, help was sought from village milk producers and district animal husbandry officer for identification of 4 to 5 farmers and collection of representative samples. All the samples were processed and analyzed for chemical composition as well as major macro and micro-minerals, using Inductively Coupled Plasma-Optical Emission Spectrometer. Results: Ca content in wheat straw (0.29%), crushed maize (0.02%) and wheat bran (0.12%) was found to be below the critical level (0.30%). The P content in concentrate ingredients was high (0.26-0.96%), but low in dry roughages (0.06-0.12%). Cereal straws (0.14%) and grains (0.12%) were deficient in Mg. Feeds and forages were found to be adequate in K (1.50%). Cereals straws were found to be deficient in S (0.11%). Greens were good source of Cu (12.02 ppm). Wheat straw was found to be low in Zn (18 ppm), but high in Mn (225 ppm) and Fe (509 ppm). Local grasses and azolla green were found to be rich source of Co (>1.00 ppm). Se (0.63 ppm) was present in appreciable quantities in most of the feedstuffs. Conclusions: From the present study, it was apparent that the feeds and forages available in the state of Jharkhand may not meet the requirements for Ca, P, Mg, Cu, Zn and Co in order to sustain a milk production of ~10 kg/day. Therefore, it is necessary to supplement these deficient minerals through area specific mineral mixture in the ration of dairy cows for improving productivity and reproduction efficiency.

• Journal of Energy Engineering
• /
• v.2 no.2
• /
• pp.194-199
• /
• 1993

Gas diffusion passes are introduced to catalyst layer so as to enlarge reaction region in cathode and anode and then improve electrode performances. The catalyst layer was manufactured with PTFE/carbon (none catalyst loaded) for gas diffusion and Pt/carbon (10 w/o Pt catalyst loaded) by varing the mixing ratio of (PTFE/carbon) to (Pt/carbon) by catalyst powdering method. The electrodes made by mixing Pt(10 w/o)/carbon powders and PTFE/carbon powders containing 60 w/o PTFE at the ratio of 7 : 3 showed the best electrode performances. It was known that by comparing the porosities to electrode performances the electrode performances were increased as both macro pore for gas diffusion and micro pore for electrolyte intrusion were formed much more. The platinum catalyst content in electrode was 0.2 mg/$\textrm{cm}^2$ and the PTFE content was 42 w/o. The electrode performance in unit cell was 220 ㎃/$\textrm{cm}^2$/0.7 V at operating temperature of 150$^{\circ}C$.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.4
• /
• pp.160-168
• /
• 2010

Recently, there are a lot of researches related to the high-fluidity concrete (HFC) with field applications. However, most applications and studies are with concretes with high strength level so there are little studies about durability evaluations such as chloride ion penetration properties with normal strength concrete. Therefore, to evaluate the durability of HFC with normal strength level, this study performed the chloride ion penetration test and observed the micro pore distribution with normal strength HFC which contains limestone powder. Experimental results showed that most micro-pores have diameters between 0.005 to 0.05 ${\mu}m$ with HFCs using limestone powder and the average diameter becomes larger with the increase of limestone powder content. Also, it was shown that, with the increase of the limestone powder content, penetration depth and diffusion coefficient of chloride ion increased and diffusion coefficient had good relationships with compressive strength and average pore diameter with the coefficient of determination over 0.90.