• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.149-152
• /
• 2006

Dry sliding wear behavior of low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the dual phase steel was compared with that of a plain carbon steel which was normalized at $950^{\circ}C$ for 30min and then air-cooled. Dry sliding wear tests were carried out using a pin-on-disk type tester at various loads of 1N to 10N under a constant sliding speed condition of 0.2m/sec against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss measured to the accuracy of $10^{-5}g$ by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and a profilomter. Micro vickers hardness values of the cross section of worn surface were measured to analyze strain hardening behavior underneath the wearing surfaces. The were rate of the dual phase steel was lower than the plain carbon steel. Oxidation on the sliding surface and strain hardening were attributed for the higher wear resistance of the dual phase steel.

• Journal of Mechanical Science and Technology
• /
• 제19권2호
• /
• pp.682-691
• /
• 2005

This paper describes the design, fabrication, and testing of a microturbine developed at Seoul National University. Here, the term 'microturbine' refers to a radial turbine with a diameter on the order of a centimeter. Such devices can be used to transmit power for various systems. The turbine is designed using a commercial CFD code, and it has a design flow coefficient of 0.238 and work coefficient of 0.542. It has 31 stator blades and 24 rotor blades. A hydrodynamic journal bearing and hydrostatic thrust bearings counteract radial and axial forces on the rotor. The test turbine consists of a stack of five wafers and is fabricated by MEMS technology, using photolithography, DRIE, and bonding processes. The first, second, fourth, and fifth layers contain plumbing, and hydrostatic axial thrust bearings for the turbine. The third wafer contains the turbine's stator, rotor, and hydrodynamic journal bearings. Furthermore, a turbine test facility containing a flow control system and instrumentation has been designed and constructed. In performance tests, a maximum rotation speed of 11,400 rpm and flow rate of 16,000 sccm have been achieved.

• Asian Pacific Journal of Cancer Prevention
• /
• 제17권4호
• /
• pp.1739-1744
• /
• 2016

We report herein an in vitro anticancer evaluation of a series of seven curcumin analogues (3a-g). The National Cancer Institute (NCI US) Protocol was followed and all the compounds were evaluated for their anticancer activity on nine different panels (leukemia, non small cell lung cancer, colon cancer, CNS cancer, melanoma, ovarian cancer, renal cancer, prostate cancer and breast cancer) represented by 60 NCI human cancer cell lines. All the compounds showed significant anticancer activity in one dose assay (drug concentration $10{\mu}M$) and hence were evaluated further in five dose assays (0.01, 0.1, 1, 10 and $100{\mu}M$) and three dose related parameters $GI_{50}$, TGI and $LC_{50}$ were calculated for each (3a-g) in micro molar drug concentrations (${\mu}M$). The compound 3d (NSC 757927) showed maximum mean percent growth inhibition (PGI) of 112.2%, while compound 3g (NSC 763374) showed less mean PGI of 40.1% in the one dose assay. The maximum anticancer activity was observed with the SR (leukemia) cell line with a $GI_{50}$ of $0.03{\mu}M$. The calculated average sensitivity of all cell lines of a particular subpanel toward the test agent showed that all the curcumin analogues showed maximum activity on leukemia cell lines with $GI_{50}$ values between 0.23 and $2.67{\mu}M$.

• 한국항행학회논문지
• /
• 제12권6호
• /
• pp.653-658
• /
• 2008

자동차에 적용되는 각종 전자 부품의 복잡도는 21세기를 맞이하면서 급속도로 변화하고 있다. 특히, 각종 전기, 전자 시스템의 급증은 자동차의 안전과 직결되는 문제로 인식되고 있다. 차량의 전장 및 전자부품을 연결해주는 커넥터는 인간의 신경망과 같아서 조그마한 접촉 불량도 차량의 운전에 심각한 영향을 미칠 수 있다. 차량의 진동과 커넥터 단자의 열 변형으로 인한 프레팅 부식은 산화막을 형성하여 접촉저항을 증가시키고 특히 산화층은 진접촉면적의 감소와 상승저항 등 터널 효과에서 급격한 상승을 보이는 결과로 제어신호를 왜곡하여 작동기의 동작오류를 초례한다. 본 논문에서는 이러한 프레팅 부식 현상을 검증하기 위한 주석으로 도금된 구리 커넥터에 스텝핑 모터를 사용하여 일정한 변위를 갖는 미세 진동을 유발하여 프레핑 부식의 진행과 접촉저항의 변화를 고찰하여 이에 대한 대비책을 강구하고자 한다.

• Mass Spectrometry Letters
• /
• 제2권2호
• /
• pp.57-60
• /
• 2011

As background significantly affects measurement accuracy and a detection limit in determination of the trace amounts of uranium, it is necessary to determine the impurities in the Lexan detector film for single particle measurements by thermal ionization mass spectrometry coupled with fission track technique (FT-TIMS). We have prepared various micro sizes of the blank Lexan detector film using a micromanipulation technique for uranium measurements by TIMS. Few tens of fg of uranium background with no remarkable dependency on the film sizes were observed in the blank Lexan films with the sizes from $50{\times}50\;{\mu}m^2$ to $300{\times}300\;{\mu}m^2$. Based on the determination of the uranium background in the Lexan film, any background correction is necessary in the isotopic analysis of a uranium single particle with micron sizes when the particle bearing Lexan film is dissected with less than $300{\times}300\;{\mu}m^2$ size. The isotopic analysis of a uranium particle in U030 standard material using TIMS was carried out to verify the applicability of the Lexan film to the single particle analysis with high accuracy and precision.

• 소성∙가공
• /
• 제16권4호
• /
• pp.299-303
• /
• 2007

Dry sliding wear behavior of ultra-fine grained(UFG) plain low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the UFG dual phase steel was compared with that of a coarse grained dual phase steel under various applied load conditions. Dry sliding wear test were carried out using a pin-on-disk type tester at various loads of 1N to 100N under a constant sliding speed condition of 0.20m/s against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss, measured to the accuracy of 10-5g by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and profilometer. Micro-vickers hardness of the cross section of worn surfaces were conducted to analyze strain hardening underneath the contact surfaces. The wear mechanism of the UFG dual phase steel was investigated with emphasis on the unstable nature of the grain boundaries of the UFG microstructure.

• 설비공학논문집
• /
• 제17권4호
• /
• pp.325-332
• /
• 2005

This paper addresses the development of a scroll expander for power generation from relatively low temperature steam source. It has a double-sided orbiting scroll member so that no thrust bearing is needed to support the base plate of the orbiting scroll. Three power transmission shafts are placed at the periphery of the orbiting scroll base plate, and these shafts can also function as anti-rotation devices. Final output is obtained from the main central shaft engaged with the three power transmission shafts through gear assembly. The clearance between the fixed and orbiting scroll elements was estimated by comparing measurement of the mass flow rate with calculation results of a computer simulation. Due to large clearance, the expander total and volumetric efficiencies were measured to be $34\%\;and\;43\%$, respectively. It has been shown through the computer simulation that the total and volumetric efficiencies could be improved to $65\%\;and\;83\%$, respectively, if the current clearance is reduced by half.

• 자원환경지질
• /
• 제51권4호
• /
• pp.323-343
• /
• 2018

본 연구에서는 석개재 지역 하부 막골층 탄산염암을 대상으로 광물조성, 미세구조 및 지화학적 특성을 분석하고 퇴적 환경에 영향을 준 유체의 특성에 대해 고찰해보았다. X-선 회절을 이용한 광물 정량 분석, SEM-BSE를 이용한 미세구조 분석에 근거하여 막골층 최하부와 하부의 탄산염암 미세구조를 4가지 Type으로 분류하고, EPMA 및 LA-ICP-MS를 이용해 각 Type 내 탄산염광물을 대상으로 주원소 및 미량원소를 분석하여 비교하였다. 다양한 크기의 반자형에서 타형의 돌로마이트 결정이 치밀하게 맞물린 구조를 갖는 Type 1과 다양한 크기의 자형에서 반자형의 돌로마이트 결정이 치밀하게 맞물린 구조를 갖는 Type 2의 돌로마이트는 상대적으로 높은 Mg/Ca ratio, 평평한 기울기의 REE 패턴, 낮은 또는 중간 이하의 Fe 함량, 낮은 Mn 함량 특성을 가진다. 돌로마이트가 광범위하고 치밀하게 맞물린 구조로 나타나는 것은 고염수로부터 지속적인 Mg 유입의 가능성을 지시한다. 반면, 세립질의 자형에서 타형의 돌로마이트 결정이 산재된 특성을 보이는 Type 3와 다양한 크기의 자형에서 반자형의 돌로마이트 결정을 갖는 Type 4는 Type 1, 2에 비해 돌로마이트 결정의 미세구조가 덜 치밀하게 맞물린 형태를 가진다. 또한 상대적으로 낮은 Mg/Ca ratio, MREE가 부화된 패턴, 중간 이상의 또는 높은 Fe 및 Mn 함량 특성을 가진다. 부분적인 돌로마이트화와 덜 치밀하게 맞물린 구조가 관찰되는 것은 해수와 염수의 혼합수 환경에서 Mg의 제한적인 유입을 지시한다. 또한 Type 4에서 나타나는 철함유 광물과 돌로마이트 결정에서 관찰되는 재결정화와 상대적으로 높은 Fe, Mn 함량을 갖는 특성은 속성 유체의 영향과 아산화 환경에 노출되면서 돌로마이트가 재결정화 작용을 받았을 가능성을 제시한다. 막골층 최하부와 하부의 주구성광물인 돌로마이트와 방해석의 광물학적, 미세구조적, 지화학적 분석을 종합한 결과, 최하부는 고염분의 대규모 퇴적수 영향을 받았고 하부는 담수와 해수의 혼합수 환경에서 속성 유체 영향을 받았음을 뒷받침한다.

• Tribology and Lubricants
• /
• 제34권3호
• /
• pp.84-92
• /
• 2018

Bearings are essential for reducing vibration and wear, in order to achieve high durability and increase longevity. White metal treatment of tilting pads via centrifugal casting method has the possibility of increasing durability. However, this manufacturing method has drawbacks such as long processing time, high defect rate, and harmful health effects. Laser cladding deposition technique is a powerful method that can address these issues by decreasing the processing time and providing good adhesion. In this study, we suggest optimum conditions for laser cladding deposition that can be used in industrial applications. We deposited a soft white metal layer on SCM440 that is primarily used in shafts to minimize wear of bearing pads. During the laser deposition process, we controlled factors such as laser power, powder feed rate, and laser head speed to determine the optimum conditions. In addition, we measured the hardness using micro Vickers, and performed field emission scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, and friction tests to investigate the mechanical properties and surface characteristics for different parameters. Based on the experimental results, we suggest that laser power, powder feed rate, and laser head speed of 1.3 kW, 2.5 rpm, and 10 mm/s, respectively, constitute the optimum conditions for producing white metals using laser cladding.

• Asian Pacific Journal of Cancer Prevention
• /
• 제17권7호
• /
• pp.3309-3315
• /
• 2016

Helicobacter pylori as the second most common cause of gastric cancer in the world infects approximately half of the developed countries population and 80% of the population living in developing countries. Integrons as genetic reservoirs play major roles in dissemination of antimicrobial resistance genes. To the best of our knowledge, this is the first study to report carriage of class 1 and 2 integrons and associated gene cassettes in H. pylori isolates from Iran. This cross-sectional study was conducted in Tehran among 110 patients with H. pylori infection. Antimicrobial susceptibility testing (AST) for H. pylori strains were assessed by the micro broth dilution method. Class 1 and 2 integrons were detected using PCR. In order to determine gene cassettes, amplified fragments were subjected to DNA sequencing of both amplicon strands. The prevalence of resistance to clarithromycin, metronidazole, clarithromycin, tetracycline, amoxicillin, rifampin, and levofloxacin were 68.2% (n=75), 25.5% (n=28), 24.5% (n=27), 19.1% (n=21), 18.2% (n=20) and 16.4% (n=18), respectively. Frequency of multidrug resistance among H. pylori isolates was 12.7%. Class 2 integron was detected in 50 (45.5%) and class 1 integron in 10 (9.1%) H. pylori isolates. The most predominant gene cassette arrays in class 2 integron-bearing H. pylori were included sat-era-aadA1, dfrA1-sat2-aadA1, blaoxa2 and, aadB whereas common gene cassette arrays in class 1 integron were aadB-aadA1-cmlA6, aacA4, blaoxa2, and catB3. The high frequency of class 2 integron and multidrug resistance in the present study should be considered as a warning for clinicians that continuous surveillance is necessary to prevent the further spread of resistant isolates.