• Journal of Welding and Joining
• /
• v.19 no.4
• /
• pp.406-412
• /
• 2001

This study is focussed on the numerical prediction of the thermal fatigue life of a ${\mu}BGA$(Micro Ball Grid Array) solder joint. Numerical method is used to perform three-dimensional finite element analysis for Sn-37mass%Pb. Sn-3.5mass%Ag solder alloys during the given thermal cycling. Strain values, along with the result of mechanical fatigue tests for solder alloys were then used to predict the solder joint fatigue life using the Coffin-Manson equation. In this study, a practical correlation for the prediction of the thermal fatigue life is suggested by using the dimensionless variable $\gamma$. As a result. it could be found that Sn-3.5mass%Ag has longer fatigue life than Sn-37mass%Pb in low cycle fatigue. In addition. the result with ${\gamm}ashow$a good agreement with the FEA results.

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.212-214
• /
• 2009

The polymer electrolyte membrane fuel cell(PEMFC) with the advantages of low-operating temperature, high current density, low cost and volume, fast start-up ability, and suitability for discontinuous operation becomes the most reasonable and attractive power system for transportation vehicle and micro-grid power plant in a household. 200W PEMFC(Polymer electrolyte membrane fuel cell) system applied to middle and small-scaled micro-grid power system was constructed by this study, then the electrical characteristics and diagnosis of the fuel cell were analyzed with thermal variation.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.486-487
• /
• 2012

In this paper, novel three-port active power decoupling (APD) method for applying 250[W] micro-inverter. This type using third port for active power decoupling stores the surplus energy and supplies sufficient energy to grid. Conventional decoupling circuit is applied in single phase grid connected micro-inverter especially single-stage configuration like flyback-type DC-AC inverter. In this passive power decoupling method, electrolytic capacitor with large capacitance is needed for decoupling from constant DC power and instantaneous AC power. However the decoupling capacitor is replaced with film capacitor by using APD, thus the overall system can achieve smaller size and long lifespan. Proposed three-port flyback inverter is verified by design and simulation.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.6
• /
• pp.412-421
• /
• 2023

As the demand for mechatronic systems and high performance increases in the machinery industry, the importance of improving friction characteristics is emphasized. During relative movement of objects, friction and wear occur on two surfaces in contact, and various methods are being designed to increase the lifespan and energy efficiency of machines. The energy increase effect using lubricants is a well-known method. In this study, a micro-sized rectangular grid pattern was produced by applying a precise micro-pattern photo lithography process. Rectangular grid patterns of the same shape and friction behavior according to the size of the pattern were produced in convex and concave shapes, and the tribological characteristics of each were analyzed.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.9
• /
• pp.958-963
• /
• 2012

Characteristics of off-grid hybrid renewable energy sources for high mountain villages are discussed. Considering reliability of electric power generation, Photovoltaic (PV)-wind hybrid and PV-hydro hybrid system are suggested. Connecting two or more villages with these hybrid systems, an extended hybrid off-grid can be formed. Sustainability of entire system is important in design of off-grid system, and income generation of the village people using the electricity should be considered.

• Progress in Superconductivity and Cryogenics
• /
• v.12 no.2
• /
• pp.17-20
• /
• 2010

A considerable amount of research material discussing designs and properties of High Temperature Superconducting Fault Current Limiter (HTS FCL) is available. However, a shortage of research concerning positioning of HTS FCL in power grid is felt. In this paper a feasibility study of HTS FCL positioning in Smart Grid through simulation analysis is carried out. A complete power network (including generation, transmission and distribution) is modeled in Simulink / SimPowerSystems. A generalized HTS FCL is also designed by integrating Simulink and SimPowerSystem blocks. The distribution network of the model has a wind turbine attached to it forming a micro grid. Three phase fault have been simulated along with placing FCL models at key points of the distribution grid. It is observed that distribution grid, having distributed generation sources attached to it, must not have a single FCL located at the substation level. Optimized HTS FCL location regarding the best fault current contribution from wind turbine has been determined through simulation analysis.

• The Journal of Korea Robotics Society
• /
• v.9 no.3
• /
• pp.154-159
• /
• 2014

The Global Positioning System (GPS) is widely used to aid the navigation of aerial vehicles. However, the GPS cannot be used indoors, so alternative navigation methods are needed to be developed for micro aerial vehicles (MAVs) flying in GPS-denied environments. In this paper, a real-time three-dimensional (3-D) indoor navigation system and closed-loop control of a quad-rotor aerial vehicle equipped with an inertial measurement unit (IMU) and a low-cost light detection and ranging (LIDAR) is presented. In order to estimate the pose of the vehicle equipped with the two-dimensional LIDAR, an octree-based grid map and Monte-Carlo Localization (MCL) are adopted. The navigation results using the MCL are then evaluated by making a comparison with a motion capture system. Finally, the results are used for closed-loop control in order to validate its positioning accuracy during procedures for stable hovering and waypoint-following.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.508-509
• /
• 2008

마이크로그리드는 소형 분산 에너지원(MicroSource)으로 이루어진 분산전원망의 총칭으로 다수의 수용가들을 위하여 수요지에서 전력을 생산 및 공급하는 기술로 기본적으로 여러 수용가의 부하 및 분산발전기들이 하나의 덩어리를 형성하게 되는 새로운 개념의 배전망이다. 계통과 분리하여 운전이 가능한 마이크로그리드는 계통 연계 시 과도현상을 줄이기 위해 연계지점의 전압, 주파수, 위상을 일치하여 투입되어야 한다. 본 논문에서는 마이크로그리드 계통 재 연계 시 과도 특성을 모의한 결과를 제시하였다. 전력계통과의 분리 후 MicroSource의 전압의 크기, 주파수 및 위상을 제어하여 전력계통에 재연계하여 과도현상을 모의하는 기초연구를 진행하였다.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.4
• /
• pp.41-47
• /
• 2009

Wind/diesel hybrid operation can be one of the most effective option for electrical power production at a remote area such as Antarctica. The king Sejong station at Antarctica relies its power production on diesel engines and diesel oil is supplied every other year by ships. However, the oil transportation processes are liable to potential oil spillage caused by the floating ice around the King George island. The long-term storage of the oil at the station can also contaminate the surrounding soils. A l0kW wind turbine has been installed to save oil consumption and operated in connection with the diesel generators since 2006. The diesel engine that operated poorly during the first year of installation was replaced in 2008 to enhance power production an recent measurements indicate that both diesel power quality and the wind turbine availability have been dramatically improved by the replacement. This report discusses electrical power qualities of wind/diesel hybrid system operating at an isolated micro gird located in the king Sejong station. Our experience reveals that the similar technologies can be applied to domestic islands, for example, in the south sea.

• Journal of Information Display
• /
• v.2 no.3
• /
• pp.72-77
• /
• 2001

Amorphous silicon thin-film transistors (a-Si TFTs) were incorporated into Mo-tip-based triode-type field emitters and diode-type ones of carbon nanotubes for an active-matrix cathode (AMC) plate of field emission displays. Also, we developed a novel surface-treatment process for the Mo-tip fabrication, which gleatly enhanced in the stability of field emission. The field emission currents of AMC plates on glass substrate were well controlled by the gate bias of a-Si TFTs. Active-matrix field emission displays (AMFEDs) with these AMC plates were demonstrated in a vacuum chamber, showing low-voltage matrix addressing, good stability and reliability of field emission, and highly uniform light emissions from the anode plate with phosphors. The optimum design of AMFEDs including a-Si TFTs and a new light shield/focusing grid is discussed.