• International Journal of Concrete Structures and Materials
• /
• v.11 no.1
• /
• pp.29-43
• /
• 2017

This study investigates the blast resistance of fiber-reinforced cementitious composite (FRCC) panels, with fiber volume fractions of 2%, subjected to contact explosions using an emulsion explosive. A number of FRCC panels with five different fiber mixtures (i.e., micro polyvinyl alcohol fiber, micro polyethylene fiber, macro hooked-end steel fiber, micro polyvinyl alcohol fiber with macro hooked-end steel fiber, and micro polyethylene fiber with macro hooked-end steel fiber) were fabricated and tested. In addition, the blast resistance of plain panels (i.e., non-fiber-reinforced high strength concrete, and non-fiber-reinforced cementitious composites) were examined for comparison with those of the FRCC panels. The resistance of the panels to spall failure improved with the addition of micro synthetic fibers and/or macro hooked-end steel fibers as compared to those of the plain panels. The fracture energy of the FRCC panels was significantly higher than that of the plain panels, which reduced the local damage experienced by the FRCCs. The cracks on the back side of the micro synthetic fiber-reinforced panel due to contact explosions were greatly controlled compared to the macro hooked-end steel fiber-reinforced panel. However, the blast resistance of the macro hooked-end steel fiber-reinforced panel was improved by hybrid with micro synthetic fibers.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.663-664
• /
• 2006

In the electronic, medical, aerospace and automobile industries, many products and parts are manufactured by joining. Recently, as these get smaller, micro joining is becoming more and more important. In this study, micro wire-to-micro wire parallel joining was performed using single mode fiber laser. Maximum power of the fiber laser is 100 W. The CCD(Charge- Coupled Device, CCD) camera to observe the specimen was made up. The objective was applied to micro joining system to make a small spot size of laser beam. In order to control the target position, micro-multi-axis-stage was set up. This paper presents results for the single mode fiber laser joining of micro wires.

• Computers and Concrete
• /
• v.4 no.1
• /
• pp.19-32
• /
• 2007

This paper is concentrated on the behaviors of five different types of fiber reinforced concrete (FRC) in uniaxial tension and flexural impact. The complete stress-strain responses in tension were acquired through a systematic experimental program. It was found that the tensile peak strains of concrete with micro polyethylene (PEF) fiber are about 18-31% higher than that of matrix concrete, those for composite with macro polypropylene fiber is 40-83% higher than that of steel fiber reinforced concrete (SFRC). The fracture energy of composites with micro-fiber is 23-67% higher than that of matrix concrete; this for macro polypropylene fiber and steel fiber FRCs are about 150-210% and 270-320% larger than that of plain concrete respectively. Micro-fiber is more effective than macro-fiber for initial crack impact resistance; however, the failure impact resistance of macro-fiber is significantly larger than that of microfiber, especially macro-polypropylene-fiber.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.23-24
• /
• 2019

In this study, analysis of steel fiber orientation and distribution inside fiber reinforced concrete was performed using micro-CT scanning technology. Samples were extracted from the column according to its height and distance from the mold. Samples were scanned in order to attain the image of steel fibers then region of interest were obtained by binarization process. By calculating the principle moment of inertia of each fiber, direction vector, scale, center postion, volume, and surface area were gained in order to analyze the orientation and distribution. Most of the fibers inside the column tended to be perpendicular to the main axis of the column. Moreover, most of the fibers appeared at the bottom of the column and at the position where it is farthest from the mold.

• Textile Coloration and Finishing
• /
• v.17 no.5 s.84
• /
• pp.1-12
• /
• 2005

Polyester fibers can be modified into cationic dyeable polyester fibers(CDP) by the copolymerization of terephthalic acid and 5-sodium sulphoisophthalic acid with ethylene glycol. The advantage of CDP on most cationic dyes is the conspicuous brilliance due to a narrow steep absorption band and the wash fastness and etc. Weight reduction by alkali hydrolysis, dyeing and solvent wicking properties of fabrics with cationic dyes, and change of fine structure were investigated. To obtain optimum splitting process parameters for dyeing and physical properties of micro CDP fiber, splitting method under various conditions was carried out. By means of SEM, it was confirmed that the splitting process of the micro CDP fiber be achieved at the weight reduction. A comparatively greater quantity of dye is necessary to dye microfiber than conventional fiber. The fastness and solvent wicking of regular CDP fiber is higher than that of micro CDP fiber.

• Korean Journal of Human Ecology
• /
• v.12 no.4
• /
• pp.529-537
• /
• 2003

This study was conducted to manufacture the soluble micro-fiber and to synthesize low melting polymer for the interior fabric not to use the polyurethane resin causing some problems. Low melting polyester for weft yarn was introduced by adding 30-40 mol% ratio of isophthalic acid to a main chain of polyethylene terephthalate to decrease the melting temperature up to heat setting temperature. Micro-fiber for warp yarn consisted of both soluble and insoluble components with multi-layered structure. When the soluble micro-fiber was treated by alkaline hydrolysis with 3-5% concentration of NaOH, it showed the turning point at 28% weight loss since soluble polyester was hydrolyzed approximate five times faster than regular polyester.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.07a
• /
• pp.20-21
• /
• 2003

Erbium doped fiber (EDF) sources are useful devices for characterization of optical components for wavelength division multiplexing (WDM) fiber optic communication system. Therefore, there are many efforts to extend the bandwidth and to increase the power of the light source. Especially, L-band ASE source uses the low inversion state of EDF. It makes the power efficiency very low and needs a lot of fiber as several times as the fiber needed in C-band ASE generation. (omitted)

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10b
• /
• pp.251-252
• /
• 2003

오염 입자 물질을 제거하기 위한 섬유상 필터는 polypropylene(이하 PP라 함) film을 fibrillate 하거나 melt blown micro fiber를 이용하여 제조할 수 있다. 특히 melt blown micro fiber web은 마스크 필터, 공기정화용 필터, 수처리용 필터 등에 폭넓게 사용되고 있다 이러한 melt blown micro web은 electret 처리에 의해 그 기능이 더욱 강화되는데, 사용 현장의 oil aerosol 노출되면 정전 특성을 빠르게 잃어버리는 경향이 있다. (중략)

• Advances in concrete construction
• /
• v.10 no.3
• /
• pp.257-269
• /
• 2020

The aim of this study is to investigate the flexural performance of hybrid fiber reinforced self-compacting concrete (HFRSCC) having different ratio of micro and macro steel fiber. A total of five mixtures are prepared. In all mixtures, the sum of the steel fiber content is 1% and also water/binder ratio is kept constant. The amount of high range water reducer admixture (HRWRA) is arranged to satisfy the workability criteria of self-compacting concrete. Four-point bending test is carried out to analyze the flexural performance of the mixtures at 28 and 56 curing days. From the obtained load-deflection curves, the load carrying capacity, deflection and toughness values are investigated according to ASTM C1609, ASTM C1018 and JSCE standards. The mixtures containing higher ratio of macro steel fiber exhibit numerous micro-cracks and, thus, deflection-hardening response is observed. The mixture containing 1% micro steel fiber shows worst performance in the view of all flexural parameters. An improvement is observed in the aspect of toughness and load carrying capacity as the macro steel fiber content increases. The test results based on the standards are also compared taking account of abovementioned standards.

• Current Optics and Photonics
• /
• v.5 no.3
• /
• pp.238-242
• /
• 2021

In this paper, we present an in line plastic-optical-fiber (POF) temperature sensor based on intensity modulation. The in line POF temperature sensor is composed of a POF, including an in-fiber micro hole filled with reversible thermochromic material, the transmittance of which depends on temperature. The reversible thermochromic material was cobalt chloride/polyvinyl butyral gel. A cobalt chloride solution of concentration 30.8 mM was formulated using 10% water/90% ethanol (v/v) solution, and gelled by dissolving polyvinyl butyral in this solution. Four types of in line POF sensors, with in line micro holes of four different diameters, were fabricated to measure temperature in the range of 25 to 75 ℃. The output optical power of all of these in line POF temperature sensors was inversely proportional to the temperature; the relation between output power and temperature was approximately linear, and the sensitivity was proportional to the diameter of the in-fiber micro hole. The experimental results indicate that an in line POF sensor can be used effectively for measuring moderate temperatures.