• Analytical Science and Technology
• /
• v.36 no.2
• /
• pp.99-104
• /
• 2023

Trace elements (TEs) have significant effects on both dental health and human health. Toxic effects are caused by deficiency or excess of TEs. This study was performed to determine levels of toxic and trace elements in incisor and molar teeth sampled from male and female participants residing in the north and south regions of Sudan. The tooth enamel of 18 extracted human teeth was analyzed using particle-induced x-ray emission (µ-PIXE) to determine its elemental profile and distribution. GeoPIXEII software package was used for the analysis of µ-PIXE data. The main elements determined were Na, Mg, P, S, Cl, K, Ca, Mn, Fe, Zn, Co, and Sr which were homogeneously distributed in the areas of the tooth enamel mapped with micro-PIXE.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.3
• /
• pp.264-274
• /
• 2013

Piping systems play an important role in gas and oil transferring system. In the piping system, there are many elements, such as valves and flow meters. In order to check their normal operating conditions, each signal from each element is displayed on the monitor in the pipe control room. By the way, there are several accidental cases in the piping system even if all signals from the local elements are judged to be normal on the monitor in the control room. Further, opposite cases often happen even the monitor shows abnormal while the local elements work normal. To overcome this abnormal functions, it is not so easy to construct the environment in which sensors detecting the working states of all elements installed in the piping system. In this paper, a new non-contact measurement technique which can calculate the elements' delicate displacements by using a PIV(particle image velocimetry) and diagnose their working states by using a neural network is proposed. The measurement system consists of a host computer, a micro system, a telescope and a high-resolution camera. As a preliminary test, the constructed measurement system was applied to measure delicate vibrations of mobile phones. For practical application, a pneumatic system was measured by the constructed system.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.74-77
• /
• 2009

Demands for high quality and productivity of precision mechanical parts are increasing greatly nowadays due to the rapid growth of information technologies and convergence industries. Therefore, core technologies for fabrication of precision mechanical parts are the fundamental issues, which are the precision machining, micro powder injection molding technologies, MR polishing, micro polymer processes, micro actuation modules and so on. These technologies are directly related to the mass production of high functional devices and machineries. Therefore, this study investigates the fabrication technologies of micro precision molds for advanced devices for possible commercialization in a near future.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.1
• /
• pp.67-74
• /
• 2008

In this paper, the surface characteristics of the AIP-TiN coated of the SKH51 and SKD11 steels under various deposition times are presented with emphasis on the comparison of the two materials. The micro-particle, the surface roughness, the micro-hardness, the coated layer thickness, the atomic distribution of Ti, N and Fe elements and the adhesion are measured for various deposition times. It has been shown that the micro-particle, the surface roughness, the coated layer thickness and the atomic distribution of Ti, N and Fe elements are similar for the two cases regardless of the test deposition time from 10 to 180 minutes. However, it has been shown that the micro-hardness and the adhesion of the SKH51 steel are higher than the SKD11 steel, indicating that they are much affected by the hardness of the material to be coated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.247-251
• /
• 2004

Chemical-Mechanical Polishing(CMP) especially is becoming one of the most important ULSI processes for the 0.25m generation and beyond. And there are many elements affecting CMP performance such as slurry, pad, process parameters and pad conditioning. Among these elements the CMP pad is considered one of the most important because of its change. But the surface of the pad has irregular pores, so there is non-uniformity of slurry flow and of contact area between wafer and the pad, and glazing occurs on the surface of the pad. So we make CMP pad with micro structure using micro molding method. This paper introduces the basic concept and fabrication technique of CMP pad with micro-structure and the characteristic of polishing. Experimental results demonstrate the removal rate, uniformity, and time vs. removal rate.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.302-304
• /
• 2004

Nuclear fuel elements containing dry recycling nuclear fuel pellets for the irradiation test in a reactor were remotely fabricated from spent PWR fuel materials in a hot cell. End closure welding as well as seal tube welding for thermal sensor of the elements was performed by Nd:YAG laser. The soundness of the end closure welds and seal tube welds for the elements were evaluated by a precise X-ray inspection system composed of a micro-focus X-ray generator with an image intensifier and a real time camera system. Then, helium leak test was performed for the elements. The soundness of the welds of the fuel elements was confirmed by the X-ray inspection and helium leak test. The irradiation test for the fuel elements were successfully completed at the HANARO research reactor.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.12 no.1
• /
• pp.64-72
• /
• 2009

The method to generate a digital elevation model(DEM) from contour lines causes a problem in which the low relief landform cannot be clearly presented due to the fact that it is significantly influenced by the expression of micro landform elements according to the interval of contours. Thus, this study attempts to develop a landcover burning method that recovers the micro relief landform of the DEM, which applies buffering and map algebra methods by inputting the elevation information to the landcover. In the recovering process of the micro landform, the DEM was recovered using the buffering method and elevation information through the map algebra for the landcover element for the micro landform among the primary DEM generation, making landcover map, and landcover elements. The recovering of the micro landform was applied based on stream landforms. The recovering of landforms using the buffering method was performed for the bar, which is a polygonal element, and wetland according to the properties of concave/convex through generating contours with a uniform interval in which the elevation information applied to the recovered landform. In the case of the linear elements, such as bank, road, waterway, and tributary, the landform can be recovered by using the elevation information through applying a map algebra function. Because the polygonal elements, such as stream channel, river terrace, and artificial objects (farmlands) are determined as a flat property, these are recovered by inputting constant elevation values. The results of this study were compared and analyzed for the degree of landform expression between the original DEM and the recovered DEM. In the results of the analysis, the DEM produced by using the conventional method showed few expressions in micro landform elements. The method developed in this study well described wetland, bar, landform around rivers, farmland, bank, river terrace, and artificial objects. It can be expected that the results of this study contribute to the classification and analysis of micro landforms, plain and the ecology and environment study that requires the recovering of micro landforms around streams and rivers.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.7
• /
• pp.542-548
• /
• 2008

A thermal mass air flow sensor (MAFS), which consists of a micro-heater and thermo-resistive sensors on the silicon-nitride ($Si_3N_4$) thin membrane structure, is micro-fabricated by MEMS processes. Two thermo-resistive temperature sensors are located at $100{\mu}m$ upstream and downstream from the micro-heater respectively. The thermal characteristics are measured to find the best measurement indicator. The micro-heater is operated under constant power condition, and four flow indicators are investigated. The normalized temperature indicator shows good physical meaning and is easy to use in practice. It is found that the configurations and heating power of thermal-resistive elements are the dominant factors to determine the range of the flow measurement in the MAFS with higher sensitivity and accuracy.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.4
• /
• pp.39-43
• /
• 2006

A computer-controlled micro tribotester has been developed to investigate the friction and wear characteristics of thin coatings, which can be applied to silicon-based materials. In the developed system, a step motor gives a reciprocating movement and an electromagnet applies a load between a ball and a plate specimen. Test results confirmed that the application of load in the range of $0.03{\sim}1.8N$ and with a sliding speed of $4.44{\sim}7.70mm/s$ was successfully accomplished. Advantages of the developed micro tribotester are: (1) realization of micro load and displacement applicable to micro electromechanical systems(MEMS) using DC motor and electromagnet (2) continuously variable load and reciprocating speed; and (3) high reliability, which allows for unattended use for long periods.

• Applied Chemistry for Engineering
• /
• v.16 no.2
• /
• pp.275-281
• /
• 2005

In this work, Scalar Passive code in Lattice Boltzmann Method was employed to simulate mixing performance of Passive mixer in a micro-channel. It physically analyzed stream line and Pressure drop for passive mixer in a micro-channel. The flow characteristics in a micro-channel was a function of Peclet number. The results indicated that the size of static element was more effect on the mixing than the number of static element and the distance of static elements.