• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.258-259
• /
• 2014

Modern concrete high safety, constructability and economy due to advantages such as buildings used for more than about 70%, but due to the low thermal performance is essential, such as installation of additional insulation is required, and therefore increase the cost of construction, as well as the construction period and condensation Symptoms such as a domestic environment, such as to inhibit the problem by generating such an improvement has been desired. In this study, we want to present the base line data for the development of improved insulation performance concrete with analyzing and evaluating the Durable Properties of the concrete combination of hollow glass microsphere and lightweight aggregate.

• The KSFM Journal of Fluid Machinery
• /
• v.8 no.5 s.32
• /
• pp.13-21
• /
• 2005

This study aims to analyze operating performance of a micro gas turbine with the aid of detailed measurements of various system parameters. In addition to embedded measurements, parameters such as exhaust temperatures, engine inlet temperatures and fuel flow rates are measured. Variations in measured data and estimated performance parameters are analyzed. Those data are processed to calculate losses along the power transmission line and the net gas turbine performance (power and efficiency based on the gas turbine shaft end) is isolated from the overall system performance. A method to estimate characteristic parameters such as component efficiencies, based on the comparison between measured and predicted performance data, is suggested and exemplified for the full load condition.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.919-920
• /
• 2008

In this paper, we present early processing techniques for visual inspection of metallic parts. Since metallic surfaces give rise to specular reflections, it is difficult to extract object boundaries using elementary segmentation techniques such as edge detection or binary thresholding. In this paper, we present two techniques for finding object boundaries on micro bit images. First, we explain a technique for detecting blade boundaries using a directional correlation mask. Second, a line and angle extraction technique based on Harris corner detector and Hough transform is described. These techniques have been effective for detecting blade boundaries, and a number of experimental results are presented using real images.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.640-643
• /
• 2003

We present investigations of the surface micromachining for transparent glass substrate, e.g. soda lime glass using tightly focused 800nm Ti:sapphire femtosecond laser. In this study, experiment conditions such as laser intensity, scanning speed, focus position were controlled as variable parameters to decide optimal machining conditions. This study shows clearly that laser intensity and scanning speed are dominant factors for good surface morphology. Using the optimal conditions, grooves with 50${\mu}{\textrm}{m}$ line width were fabricated on glass substrate and their surface morphologies were investigated from SEM image.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1215-1219
• /
• 2003

Light Guide Panel(LGP) is a key part of backlight unit(BLU) which transforms line-light of lamp to surface-light. Dot pattern is formed on the injected LGP surface by screen printing. This dot pattern is composed of several ten thousands micro dots of diameter 150-180$\mu\textrm{m}$ or so. The dot patterning by screen printing causes low productivity and low performance of TFT-LCD. This research develops the micromachining technology for LGP mould which could form micro dot pattern by injection molding, removing the existing screen printing process.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2005.03a
• /
• pp.413-417
• /
• 2005

A lattice model of a typical bridge column section is analyzed, and results are presented. The lattice is built as an ensemble of line elements and masses, that can capture strain rate dependency of concrete material. The research mainly breaks up into two parts: First, a micro level analysis of the material is executed, and control parameters of the governing equations are derived by matching the results with the common macroscopic properties of concrete material. Then, the properties exhibited by the micro model, which extends the classical material properties are applied to the mesoscale model. Hence, the analysis of the target structure can be performed. In the mesoscale analysis, ramp-like impulse loads are applied at different velocity, so that the contribution of the material level rate dependency to the global behavior of the structure can be tracked.

• Proceedings of the KIEE Conference
• /
• 2002.04a
• /
• pp.34-36
• /
• 2002

This paper addresses an elevator position control scheme in unified control system. Conventional systems have employed independent micro-processors for speed, car, and group control respectively and the car controller generates a velocity command by combining the time-based and distance-based velocity pattern. In this scheme, it is inevitable that an elevator creeps in the vicinity of target floor, or stops abruptly. The proposed control system employs only one high-performance micro-processor, which can execute the car and group control as well as the speed control. It simply generates the desired position trajectory based on time and on-line corrects a velocity pattern to make the position error be zero. Experimental results show the feasibility of the proposed control scheme.

• Laser Solutions
• /
• v.13 no.2
• /
• pp.6-9
• /
• 2010

In printed electronics, printing rolls are used to transfer electronic ink onto a flexible substrate. Generally printing rolls are being made by the indirect laser method which is based on the etch process, thus not environment-friendly and not suitable for making a large printing roll. For the pursuit of making a large printing roll for mass printing of electronic devices, we have directly engraved micro-patterns into a Zn plated printing roll using a 30W pulse-modulated fiber laser. We have successfully engraved line patterns ranging from about 15-30${\mu}m$ in width.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.227-230
• /
• 2002

New polishing technique for small parts has been tried out using the principle of particle electromechanics. Common fine abrasives such as alumina, diamond, silicon carbide are dielectric materials which are polarized under an electric field, and a non-uniform electric field makes abrasive particles translate along the field line. Using this principle, We make abrasive particles aggregate in the vicinity of the micro tool which is fir the surface finishing of a small part without contact with it. The behavior of particles is optically measured, and the machined depth of glass is examined.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.132-139
• /
• 2004

This study aims to analyze operating performance of a micro gas turbine with the aid of detailed measurements of various system parameters. In addition to embedded measurements, parameters such as exhaust temperatures, engine inlet temperatures and fuel flow rates are measured Variations in measured data and estimated performance parameters are analyzed. Those data are processed to calculate losses along the power transmission line and the net gas turbine performance (power and efficiency based on the gas turbine shaft end) is isolated from the overall system performance. On the basis of the measured data, analytical approach is tried to estimate design characteristic and performance parameters such as component efficiencies and unmeasured temperatures.