• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.186-189
• /
• 2001

The main method in micro-etching process, used in manufacturing semiconductors, electronic components, circuits, is Photo Masking method that exposes and develops on the photo-sensitivity solutions or films. This method enables one to process highly precisely, $\pm$0.03 mm in end line location area. But this has limits in a high speed / wide width process, difficulties in endless masking, and the problem of high price. We have developed the direct masking method to make use of Gravure printing, widely used in grocery packing sheet printing. We made cylinder tools to influence the masking quality by laser stream process. We have confirmed that the end line location accuracy in the line width of the product is improved from 0.12 mm to $\pm$0.07 mm level, after etching process.

• 한국정밀공학회지
• /
• 제23권3호
• /
• pp.56-60
• /
• 2006

A high-resolution shadow mask, or called a nanostencil was fabricated for high resolution lithography. This high-resolution shadowmask was fabricated by a combination or MEMS processes and focused ion beam (FIB) milling. 500 nm thick and $2{\times}2mm$ large membranes wore made on a silicon wafer by micro-fabrication processes of LPCVD, photolithography, ICP etching and bulk silicon etching. A subsequent FIB milling enabled local membrane thinning and aperture making into the thinned silicon nitride membrane. Due to the high resolution of the FIB milling process, nanoscale apertures down to 70 nm could be made into the membrane. By local deposition through the apertures of nanostencil, nanoscale patterns down to 70 nm could be achieved.

• 한국공작기계학회논문집
• /
• 제16권2호
• /
• pp.70-77
• /
• 2007

The application of focused ion beam(FIB) technology has been broadened in the fabrication of nanoscale regime. The extended application of FIB is dependent on complicated reciprocal relation of operating parameters. It is necessary for successful and efficient modifications on the surface of silicon substrate. The primary effect by Gaussian beam intensity is significantly shown from various aperture size, accelerating voltage, and beam current. Also, the secondary effect of other process factors - dwell time, pixel interval, scan mode, and pattern size has affected to etching results. For the process analysis, influence of the secondary factors on FIB micromilling process is examined with respect to sputtering depth during the milling process in silicon material. The results are analyzed by the ratio of signal to noise obtained using design of experiment in each parameter.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.871-874
• /
• 2004

Fabrication of a high-resolution shadow mask, or called nanostencil, is presented. This high-resolution shadowmask is fabricated by a combination of MEMS processes and focused ion beam (FIB) milling. 500 nm thick and 2x2 mm large membranes are made on a silicon wafer by micro-fabrication processes of LPCVD, photolithography, ICP etching and bulk silicon etching. Subsequent FIB milling enabled local membrane thinning and aperture making into the thinned silicon nitride membrane. Due to high resolution of FIB milling process, nanoscale apertures down to 70 nm could be made into the membrane.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 유기절연재료 방전 플라즈마연구회
• /
• pp.77-80
• /
• 2003

MEMS(Micro Electro Mechanical System) 기술에서 실리콘 식각기술의 중요성으로 플라즈마 식각기술의 개발이 꾸준히 진행되고 있다. 이중에서 ICP(Inductive Coupled Plasma)는 기존의 증착장치에 유도결합식 플라즈마를 추가로 발생시켜 증착막의 특성을 획기적으로 개선시키는 가장 최근에 개발된 기술이며, 이용에너지를 증가시키지 않고도 이용밀도를 높이고 이용업자들에 방향성을 가할 수 있는 새로운 플라즈마 기술로, 주로 MEMS 제조공정에 응용되고 있다. 본 연구에서는 STS-ICP $ASE^{HR}$을 이용하여 식각과 증착공정을 반복하여 식각을 하는 Bosch 식각에 관하여 연구하였다 STS-ICP $ASE^{HR}$ 장비의 Platen power, Coil power 및 Process pressure에 다양한 변화를 주어 각 변수에 따른 식각속도를 관찰하였다. 각 공정별 변수를 변화시킨 결과 Platen power 12W, Coil power 500W, 식각/Passivation Cycle 6/7sec 일 경우 식각속도는 $1.2{\mu}m$/min 이었고, Sidewall profile은 $90{\pm}0.7^{\circ}$로 나타나 매우 우수한 결과를 보였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.739-742
• /
• 2002

This paper described on the fabrication of microstructures by DRIE(deep reactive ion etching). SOI(Si-on-insulator) electric devices with buried cavities are fabricated by SDB technology and electrochemical etch-stop. The cavity was fabricated the upper handling wafer by Si anisotropic etch technique. SDB process was performed to seal the fabricated cavity under vacuum condition at -760 mmHg. In the SDB process, captured air and moisture inside of the cavities were removed by making channels towards outside. After annealing($1000^{\circ}C$, 60 min.), The SDB SOI structure was thinned by electrochemical etch-stop. Finally, it was fabricated microstructures by DRIE as well as an accurate thickness control and a good flatness.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 D
• /
• pp.1558-1560
• /
• 1998

Macroporous silicon diaphragms 20 to $200{\mu}m$ thick have been formed on p-type silicon by anistropic etching in TMAH solution and then by electrochemical etching in HF-ethanol-water solution with an applied current. The pores have a pore diameter of $1.5{\sim}2{\mu}m$, with a depth of $20{\sim}30{\mu}m$ and are not interconnected, which are in sharp contrast to the porous silicon reported previouly for similarly doped p-Si. The fabrication of macroporous silicon and free-standing diaphragms is expected to offer new applications for microsensors, micro-machining, and separators.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권1호
• /
• pp.34-38
• /
• 2008

The surface texture of a product is generally produced by etching or sandblasting. However, these techniques have problems related to repeatability and environmental pollution. Since current milling machines can produce small parts at the micrometer or nanometer level, the resolution of milling exceeds the manufactured dimensions of the surface texture produced by etching or sand-blasting. A method for generating surface texture by milling is proposed and demonstrated. The proposed method was demonstrated by actual milling using a three- or five-axis control machine, and the machined surface texture was measured with an interferometer to allow comparison with the designed shape. The measurement results demonstrate that the proposed method can generate a wide-area surface texture with good machining repeatability.

• 한국정밀공학회지
• /
• 제28권2호
• /
• pp.245-250
• /
• 2011

A high-resolution shadow mask, a nanostencil, is widely used for high resolution lithography. This high-resolution shadowmask is often fabricated by a combination of MEMS processes and focused ion beam (FIB) milling. In this study, FIB milling on 500-nm-thin SiN membrane was tested and characterized. 500 nm thick and $2{\times}2$ mm large membranes were made on a silicon wafer by micro-fabrication processes of LPCVD, photolithography, ICP etching and bulk silicon etching. A subsequent FIB milling enabled local membrane thinning and aperture making into the thinned silicon nitride membrane. Due to the high resolution of the FIB milling process, nanoscale apertures down to 60 nm could be made into the membrane. The nanostencil could be used for nanoscale patterning by local deposition through the apertures.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.2001-2003
• /
• 1996

In this study, Allied Signal 211 SOG was used as a sacrificial material. After researching its etching properties, we adapted it to bottom-drive micrometers. SOG was superior etch rate and roughness to them of PSG or CVD-oxide and possible to low-temperature processing. Etching properties of SOG depended on the temperature and duration of its bake and cure. SOG used in the fabrication of bottom-drive micrometers showed us usefulness as a sacrificial layer and haying a least influence on machines on it in comparison with conventional sacrificial materials.