• Journal of the Korean Society for Heat Treatment
• /
• v.27 no.3
• /
• pp.115-120
• /
• 2014

Microstructural features were comparatively investigated in AZ91 (Mg-9%Al-1%Zn) and AZ91-0.5%Sn alloys, in order to clarify the reason for the enhancement in room temperature tensile properties by the addition of small amount of Sn in Mg-Al-based alloy. In as-cast state, the Sn-containing alloy showed increased YS, UTS and elongation than the Sn-free alloy. The microstructural examination revealed that various factors including finer cell size, reduction of lamellar (${\alpha}+{\beta}$) phase and morphological change of bulky ${\beta}$ phase from partially divorced shape to fully divorced shape, are likely to be responsible for the improvement in tensile properties for the Sn-containing alloy. It is noted that two alloys showed similar tensile properties after solution treatment. This implies that microstructural evolution related to the ${\beta}$ phase plays a key role in better tensile properties in the Sn-containing alloy.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.11a
• /
• pp.270-270
• /
• 2017

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.179-180
• /
• 2015

pure Mg and some Mg alloys are relatively rapidly corroded after operation, resulting in the decrease of mechanical strength and change of local ion concentration. In this study, the corrosion mechanism of biodegradable implant materials was investigated by corrosion tests of the Mg alloy in Hank's solution. Particularly, the crystal structures and chemical bonding state of corrosion reactants was systematically examined.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.2
• /
• pp.223-226
• /
• 2012

Liquid livestock manure (LLM) has been used as a nitrogen fertilizer source for horticulture plants. LLM contains organic nitrogen (N), ammonium, nitrate, and nitrite. The amount of nitrate and nitrite in LLM are usually small compared to the amount of ammonium in it and so they can be negligible if total nitrogen (N) concentration in LLM is higher than $1,000mg\;L^{-1}$. However, if total N concentration in LLM is less than $1,000mg\;L^{-1}$, the amount of nitrate and nitrite may affect total N concentration in LLM. Currently, Kjeldahl digestion method is mainly used for ammonium-N in LLM. Therefore, it is ineffective to analyze nitrate-N and nitrite-N. The objective of this study was to evaluate whether the total N concentrations are affected by the amount of nitrate-N and nitrite-N with diverse LLMs by Kjeldahl method (with and without Devarda's alloy after Conc. sulfuric acid digestion). Five liquid livestock manure samples were collected at swine farms in Ansung and Icheon. All LLM samples were stored at $25^{\circ}C$, subsampled at every $15^{th}$ day for 90 days, and analyzed for total N, ammonium-N, and nitrate-N. At the $90^{th}$ day, LLM samples were analyzed with and without Devarda's alloy after Conc. sulfuric acid digestion. Potassium nitrate, ammonium nitrate, and ammonium chloride were used to determine the N recovery percentages. Total N concentration ranged from 560 to $4,230mg\;L^{-1}$. Nitrate-Ns were found in all LLM samples, ranged from 21 to $164mg\;L^{-1}$. N recovery percentages with potassium nitrate were 0 % without Devarda's alloy and 100% with Devarda's alloy because adding Devarda's alloy facilitated nitrate-N into ammonium-N conversion. Total Ns were significantly different between two methods, with and without Devarda's alloy. Total N concentrations were $210mg\;L^{-1}$ at LLM 4 and $370mg\;L^{-1}$ at LLM 5 without Devarda's alloy and $290mg\;L^{-1}$ at LLM 4 and $490mg\;L^{-1}$ at LLM 5 with Devarda's alloy. These results suggest that if total N of LLM is less $1,000mg\;L^{-1}$, additional procedure such as adding Devarda's alloy can be used to estimate the total N and inorganic N better.

• Journal of Korea Foundry Society
• /
• v.40 no.3
• /
• pp.66-75
• /
• 2020

The aim of this study was to optimize a solid solution treatment for a high pressure die casting Al-10Si-0.3Mg-0.6Mn alloy to avoid blistering and to improve the strength of the alloy. To achieve this goal, the number density of the blisters and the strength of the alloy under various solid solution treatment (SST) conditions were evaluated. The SST was performed at 470, 490, 510 and 530℃ for 20, 60, 120, 240 and 480 min on the alloy. The number density of the blisters increased with the increasing temperature and time of the SST and the defect area fraction. The yield strength of the alloy after the T6 heat treatment increased with the increasing SST temperature and time. Based on the results, it is suggested that SST should be performed at 510℃ within 60 min. or at 470 and 490℃ within 240 min. to avoid blistering and to improve the strength.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.47-51
• /
• 2014

In this work, a possible mechanism for grain evolution in Al-Mg alloy films during thermal annealing is suggested on the basis of the phase transition and the related residual stress. Al-Mg alloy films with compositions of 14.0 and 18.0 wt% Mg content were deposited on cold-rolled steel substrates by the direct current co-sputtering method using Al and Mg targets. After the deposition, the samples were thermally annealed at $400^{\circ}C$ for 10 min. The featureless, dense cross-sectional microstructure of the as-deposited films turned into a grainy microstructure after the thermal annealing. According to the residual stress evaluated by using the $XRD-sin2{\psi}$ technique and the phase analysis by XRD, it is likely that grains were created in order to relieve the additional accumulation of residual stress originating from the phase transition from face-centered cubic Al (${\alpha}$) to Al3Mg2 (${\beta}$) and Mg (${\delta}$) phases, suggesting interplay between the microstructure and residual stress.

• Korean Journal of Materials Research
• /
• v.13 no.12
• /
• pp.819-824
• /
• 2003

The Al-7.7Zn-2.0Mg-1.9Cu-0.1Zr-0.1Sc alloy exhibited excellent elongation by the new thermomechanical treatment (TMT) process; solution treatment and furnace cooling\longrightarrowhot and cold rolling and then annealing for short time. Tensile test at high temperature from 430 to $500^{\circ}C$ has been performed with various strain rates using for the Al-7.7Zn-2.0Mg-1.9Cu-0.1Zr-0.1Sc alloy obtained by the TMT process. The elongation of the Al-7.7Zn-2.0Mg-1.9Cu-0.1Zr-0.1Sc was 550% tensile tested at $470^{\circ}C$ temperature and 2.2 $\times$ $10^{-3}$ $s^{-1}$ strain rate. The m value of Al-7.7Zn-2.0Mg-1.9Cu-0.1Zr-0.1Sc alloy deformed 85% increased from 0.33 to 0.46 with increasing total elongation. This new TMT process was very simple and easy to make the sheets in the company.

• Journal of the Korean institute of surface engineering
• /
• v.52 no.5
• /
• pp.265-274
• /
• 2019

Formation behavior of PEO (Plasma Electrolytic Oxidation) films on AZ31 Mg alloy was investigated under application of 310 Hz AC as a function of $Na_3PO_4$ concentration from 0.02 M to 0.2 M. Film formation voltage and in-situ observation of arcs generated on the specimen surface were recorded with time, and surface morphologies of the PEO films were investigated using optical microscopy, confocal scanning laser microscopy and scanning electron microscopy. PEO film formation voltage decreased linearly with increasing $Na_3PO_4$ concentration which is attributed to the increase of solution pH. PEO films were grown uniformly over the entire surface in $Na_3PO_4$ solutions between 0.05 M and 0.1 M. However, non-uniform PEO films with white spots were formed in $Na_3PO_4$ solutions containing more than 0.1 M. Thickness and roughness of PEO films on AZ31 Mg alloy increased linearly with increasing $Na_3PO_4$ concentration and their increasing rates appeared to be much higher under 1 M than above 1 M. The experimental results suggest that phosphate ions can contribute to the formation of PEO films but higher $Na_3PO_4$ concentration more than 1 M results in local damages of PEO films due to repeated generation of white arcs at the same surface site of AZ31 Mg alloy.

• Journal of Korea Foundry Society
• /
• v.35 no.6
• /
• pp.147-154
• /
• 2015

The effects of Sc and Sr elements on the modification of the eutectic $Mg_2Si$ phase and the castability were investigated in the Al-4wt%Mg-0.9wt%Si-0.3wt%Mn-0.15wt%Fe alloy. Measurements of the cooling curve and microstructure observations were performed to analyze the additional effects of Sc and Sr minor elements during the solidification process. A prominent effect found on the modification of the eutectic $Mg_2Si$ phase with additions of the Sr and Sc elements. Here, a fine eutectic $Mg_2Si$ phase and a decrease in the growth temperature of the eutectic $Mg_2Si$ phase were evident with an addition of Sc element up to 0.2 wt%. The growth temperature of the eutectic $Mg_2Si$ phase decreased and the effect on the modification of the eutectic $Mg_2Si$ phase increased with the addition of Sr element up to 0.02 wt%. The addition of 0.02wt%Sr had the strongest effect on the modification of the eutectic $Mg_2Si$ phase, and the resulting microstructure of the eutectic $Mg_2Si$ phase was found to have a fibrous morphology with a decreased aspect ratio and an increased modification ratio. Fluidity and shrinkage tests were conducted to evaluate the castability of the alloy. The addition of 0.02wt%Sr effectively increased the fluidity of the alloy, while an addition of Sc did not show any effect compared to when nothing was added. The maximum filling length was recorded for 0.01wt%TiB-0.02wt%Sr owing to the effect of the fine ${\alpha}$-Al grains. The macro-shrinkage ratio decreased, while the micro-shrinkage ratio increased with the addition of various eutectic modifiers. The highest ratio of micro-shrinkage was recorded for the 0.02wt%Sr condition. However, the total shrinkage ratio was nearly identical regardless of the amounts added in this study.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.480-481
• /
• 2008

The aim of this work is to compare the microstructure, the texture, of an AZ31 Mg alloy processed via cold rolling process. Initial AZ31 Mg alloy sheet samples with strong {0002} texture were cut along the angles of 12.5 and 25 degrees to normal direction (ND). These specimens were rolled in room temperature condition. The microstructure was characterized by optical microscopy and the texture was measured by X-ray diffraction.